Elsay ESP8266 Wi-Fi Single 30A Relay Module
Nkọwapụta
- Aha ngwaahịa: Elsay ESP8266 WIFI Single 30A Relay Module
- Nkwanye ike: DC7-80V/5V
- Modul WiFi: ESP-12F
- Oke osisi: 78 x 47mm
- Arọ: 45g
Ntuziaka ojiji ngwaahịa
Atụmatụ arụrụ arụ
Elsay ESP8266 otu 30A relay development bọọdụ dabara adaba maka mmụta mmepe sekọndrị ESP8266, njikwa ikuku ụlọ smart na ngwa ndị ọzọ. Ọ na-abịa na koodu ntụaka gburugburu mmepe Arduino.
Okwu mmalite na nkọwa
Okwu Mmalite
- Ọdụ ụgbọ mmiri na-ere ọkụ: GND, RX, TX, 5V nke ESP8266 jikọtara na GND, TX, RX, 5V nke mpụta TTL serial modul n'otu n'otu. Ekwesịrị ijikọ IO0 na GND mgbe ị na-ebudata.
- Mpụta mbugharị: NC (ọnụ ọnụ mechiri emechi), COM (ọnụ ọnụ), NO (ọnụ na-emeghe ọnụ).
GPIO Pinout ọdụ ụgbọ mmiri
- ADC, EN, IO16, IO14, IO12, IO2, IO15, GPIO16, GPIO14, GPIO12, TXD, RXD, GND, IO13, GPIO13, 5V, IO5, 3.3V, IO4, RY1, IO0
Ntọala gburugburu mmepe Arduino
- Wụnye Arduino IDE 1.8.9 ma ọ bụ ụdị kachasị ọhụrụ.
- Mepee Arduino IDE, gaa na File - Mmasị, gbakwunye onye njikwa bọọdụ ESP8266 URL.
- Na Ngwaọrụ - Onye njikwa Board Development, chọọ ESP8266 wee wụnye ngwugwu nkwado.
Nbudata mmemme
- Jikọọ IO0 na GND ntụtụ site na iji okpu jumper.
- Jikọọ a TTL serial modul (dịka, FT232) na kọmputa USB na mmepe osisi.
- Họrọ osisi mmepe na Ngwaọrụ - Board Development.
- Họrọ nọmba ọdụ ụgbọ mmiri ziri ezi na Ngwaọrụ – Port.
- Pịa bulite iji chịkọta na budata mmemme na bọọdụ mmepe.
- Kwupu njikọ IO0 na GND mgbe ebulitechara ka mmemme ahụ rụọ ọrụ.
FAQ
- Ajụjụ: Gịnị bụ ike ọkọnọ nso maka modul a?
A: The modul na-akwado DC7-80V/5V ike ọkọnọ mode. - Ajụjụ: Kedu ka m ga-esi budata mmemme na bọọdụ mmepe?
A: Ị nwere ike iji okpu jumper jikọọ IO0 na GND pin, wee jikọọ a TTL serial modul ka bulite mmemme site na iji Arduino IDE.
DC7-80/5V kwadoro ESP8266 WIFI otu 30A relay modul
gafereview
Elsay ESP8266 otu 30A relay Development Board nwere ESP-12F WiFi modul, ọdụ ụgbọ mmiri I/O na-agbaji nke ọma, na-akwado ọnọdụ ọkọnọ ike DC7-80V/5V. Nye koodu ntụaka gburugburu mmepe Arduino, dabara maka mmụta mmepe sekọndrị ESP8266, njikwa ikuku ụlọ mara mma na oge ndị ọzọ.
Atụmatụ arụ ọrụ
- on-board tozuru okè na kwụsiri ike ESP-12F WiFi modul, nnukwu ike 4M Byte Flash;
- WiFi modul I / O ọdụ ụgbọ mmiri na UART mmemme nbudata ọdụ ụgbọ mmiri niile na-eduga, adaba maka mmepe nke abụọ;
- ike ọkọnọ na-akwado DC7-80V / 5V;
- on-board WiFi modul RST bọtịnụ nrụpụta na igodo mmemme;
- ESP-12F na-akwado iji Eclipse/Arduino IDE na ngwa mmepe ndị ọzọ, iji nye mmemme ntụaka n'okpuru gburugburu mmepe Arduino;
- on-board 1-ụzọ 5V/30A ọsọ agba anọ, mmepụta mgba ọkụ akara, adabara ịchịkwa njikwa nke ibu n'ime voltaji arụ ọrụtage nke AC 250V/DC30V;
- Ngosipụta ike na bọọdụ na ihe ngosi relay, ESP-12F na-abịa na LED nwere mmemme 1.
Okwu mmalite na nkọwa
osisi size: 78 * 47mm
Arọ: 45g
Okwu Mmalite
Ọdụ ụgbọ mmiri na-ere ọkụ: Ejikọtara GND, RX, TX, 5V nke ESP8266 na GND, TX, RX, 5V nke TTL serial modul dị n'otu n'otu, IO0 kwesịrị ijikọ na GND mgbe ị na-ebudata, wee kwụpụ njikọ dị n'etiti IO0 na GND mgbe nbudata nbudata. ;
Mbupute mbugharị
NC: ọdụ ụgbọ ala mechiri emechi, nke dị mkpụmkpụ na COM tupu etinye uche na relay, kwụsịtụrụ mgbe nnabata;
COM: ọnụ ọnụ ọnụ;
Mba: Ọ na-emeghe ọnụ ọnụ, a na-akwụsịtụ relay tupu etinye ya, ma na-akpụ ya na COM mgbe etinyechara ya.
Okwu mmalite nke GPIO Pinout Ports
| Oghere Usoro
ọnụọgụgụ |
aha | Nkọwa ọrụ | ọnụọgụ nọmba | aha | Nkọwa ọrụ |
| 1 | ADC | Nsonaazụ ntụgharị A/D. Ntinye voltage nso 0 ruo 1V, oke uru: 0 ruo
1024 |
10 | IO2 | GPIO2; UART1_TXD |
| 2 | EN | Kwado pin, ndọpụta ndabara | 11 | IO15 | GPIO15; MTDO; HSPI_CS;
UART0_RTS |
| 3 | IO16 | GPIO16 | 12 | TXD | UART0_TXD; GPIO1 |
| 4 | IO14 | GPIO14; HSPI_CLK | 13 | RXD | UART0_RXD; GPIO3 |
| 5 | IO12 | GPIO12; HSPI_MISO | 14 | GND | ALA IKE |
| 6 | IO13 | GPIO13; HSPI_MOSI;
UART0_CTS |
15 | 5V | 5V ike ọkọnọ |
| 7 | IO5 | GPIO5 | 16 | 3.3V | 3.3V ike ọkọnọ |
| 8 | IO4 | GPIO4 | 17 | RY1 | Maka ọdụ ụgbọ mmiri relay, enwere ike iji okpu mkpụmkpụ na IO16 mee ihe; iji jiri I/O ndị ọzọ na-anya ụgbọ ala, DuPont waya jumper nwere ike iji |
| 9 | IO0 | GPIO0 |
Ntọala gburugburu mmepe Arduino
ESP8266 na-akwado Eclipse/Arduino IDE na ngwa mmepe ndị ọzọ, iji Arduino dị mfe, nke a bụ gburugburu mmepe Arduino iji wuo ụzọ:
- wụnye Arduino IDE 1.8.9 ma ọ bụ ụdị kachasị ọhụrụ;
- mepee Arduino IDE, pịa mmanya menu File – Mmasị, tinye Mmasị na “ mgbakwunye mmepe osisi njikwa URL” na pịa ka ịgbakwunye URL:
http://arduino.esp8266.com/stable/package_esp8266com_index.json, 
pịa ogwe menu nke Ngwaọrụ - Board Development - Development Board Manager, wee chọọ "ESP8266" iji wụnye ngwugwu nkwado Arduino maka ESP8266 2.5.2 ma ọ bụ ụdị kachasị ọhụrụ! 
Budata mmemme
- jiri jumper okpu jikọọ IO0 na GND atụdo, kwadebe a TTL Oghere Usoro modul (eg, FT232) plugged n'ime kọmputa USB, Oghere Usoro modul na mmepe osisi usoro bụ ndị a:
Oghere Usoro TTL ESP8266 Development Board GND GND TX RX RX TX 5V 5V - pịa ihe nrụnye menu - Board Development, họrọ bọọdụ mmepe maka ESPino (modul ESP-12)
- mepee mmemme ịchọrọ ibudata, pịa Ngwaọrụ – Port na menu mmanya, họrọ nọmba ọdụ ụgbọ mmiri ziri ezi.
- pịa “Bulite” na a ga-achịkọta mmemme na-akpaghị aka wee budata ya na bọọdụ mmepe, dị ka ndị a:
na n'ikpeazụ kwụsịrị IO0 na GND, mmepe osisi re-power ma ọ bụ pịa bọtịnụ nrụpụta ihe omume nwere ike na-agba ọsọ.
Akwụkwọ / akụrụngwa
 |
Elsay ESP8266 Wi-Fi Single 30A Relay Module [pdf] Akwụkwọ ntuziaka onye nwe DC7-80-5V, XL4015, ESP8266 Wi-Fi Single 30A Relay Module, ESP8266, Wi-Fi Single 30A Relay Module, Single 30A Relay Module, Ntugharị Module, Module |
