Home » ICP » icp PCIE-Q470 Full-size PICMG 1.3 CPU Card Installation Guide 
icp PCIE-Q470 Full-size PICMG 1.3 CPU Card
Package List
PCIE-Q470 package includes the following items
- 1 x PCIE-Q470 single board computer
- 1 x SATA cable
- 1 x Mini jumper pack
- 1 x QIG
Specifications
- CPU:
10th/11th Generation LGA1200 Intel® Core™ i9/i7/i5/i3, Pentium® and Celeron® processors
- Chipset:
Intel® Q470
- Memory:
Four 288-pin 2933 MHz dual-channel DDR4 DIMM slots supporting up to 128 GB memory
- BIOS:
AMI UEFI BIOS
- Graphics Engine:
- 10th Generation CML-S: up to Intel® UHD Graphics 630, Intel® HD 9th Generation Display Engine based on 16 low power execution units supporting DX2015, OpenGL 5.X and OpenCL2.x, ES 2.0
- 11th Generation RKL-SXe: 12th Generation Graphics Architecture, Intel® UHD Graphics 750, supporting 12-bit end-to-end, AV1, VP9, HEVC 12b, HDR10, FP16
- Display Output:
1 x HDMI 1.4 (up to 4096 x 2160 @ 30 Hz)
- Ethernet:
- LAN1: Intel® I225V 2.5GbE controller (Colay with I225-LM)
- LAN2: Intel® I225V 2.5GbE controller (Colay with I225-LM)
- External I/O Interface:
- 2 x USB 3.2 Gen 1 (5Gb/s) (Type-A)
- 1 x USB 3.2 Gen 2 (10Gb/s) (Type-C)
- Internal I/O Interface:
- 4 x SATA 6Gb/s (RAID 0/1/5/10 supported)
- 6 x USB 2.0 (2×4 pin, p=2.54)
- 2 x USB 3.2 Gen 1 (5Gb/s) (2×10 pin, p=2.0)
- 1 x USB 3.2 Gen 1 (Type-A, 180°)
- 2 x RS-232 (2×5 pin, p=2.0)
- 2 x RS-422/485 (1×4 pin, p=2.0)
- Audio:
1 x IAUDIO connector supporting IEI AC-KIT-888S audio module (2×5 pin, p=2.0)
- Front Panel:
1 x Front panel (2×7 pin, p=2.54; power LED, HDD LED, power button, reset button, speaker)
- LAN LED:
2 x LAN LED (1×2 pin, p=2.54)
- Expansions:
- 1 x PCIe x16 signal via golden finger (supporting x16, or x8 + x8, or x4 + x4 + x8)
- 4 x PCIe x1 signal from PCH via golden finger (supporting one x4, or four x1)
- 4 x PCI signal via golden finger
- 1 x M.2 2230 A Key (PCIe x2 & USB 2.0)
- 1 x M.2 3042/3052 B Key w/ SIM holder (PCIe Gen3 x2)
- 1 x M.2 2280/2242 M Key on solder side (PCIe x4)
- Digital I/O:
1 x 12-bit digital I/O (2×7 pin, p=2.0)
- SM Bus:
1 x SM Bus (1×4 pin, p=1.25)
- I2C:
1 x I2C (1×4 pin, p=1.25)
- Fan Connector:
1 x CPU fan connector (1×4 pin)
1 x System fan connector (1×4 pin)
- Chassis Intrusion:
1 x Chassis intrusion connector (1×2 pin, p=2.54)
- TPM:
Intel® PTT (TPM 2.0)
- Power Supply:
- ATX/AT power supply
- Support AT/ATX mode
- ErP/EuP compliant
- Power Consumption:
- 3.3V@1.04A, 5V@8.61A, 12V@12.33A
- (Intel® Core™ i9-11900K CPU with 4 GB 3200 MHz DDR4 memory)
- Watchdog Timer:
Software programmable support 1–255 sec. system reset
- Operation Temperature: 0°C – 60°C
- Storage Temperature: -30°C – 70°C
- Operation Humidity: 5% – 95%, non-condensing
- Dimensions: 338 mm x 126 mm
- Weight: GW:1000 g / NW:500 g
- Safety: CE/FCC compliant
All the drivers and utility for the PCIE-Q470 are available on IEI Resource Download Center. Type PCIE-Q470 and press Enter to find all the relevant software, utilities, and documentation. To install software from the downloaded ISO file, mount the file as a virtual drive to view its content.
IEI Resource Download Center
https://download.ieiworld.com
Ordering Information
- PCIE-Q470-R10:
Full-size PICMG 1.3 CPU card supports 10th/11th Gen. LGA1200 Intel® Core™ i9/i7/i5/i3, Pentium® and Celeron® processors, Intel® Q470, DDR4 DIMM, HDMI, dual Intel® 2.5GbE, USB 3.2 Gen 2, SATA 6Gb/s, M.2, iAudio and RoHS
- CB-USB02-RS:
Dual port USB cable with bracket, 300mm, p=2.54
- 32102-000100-200-RS:
SATA power cable, MOLEX 8981-4M to SATA15P, 150mm
- 32205-002700-200-RS:
RS-232/422/485 cable, 200mm, p=2.0
- AC-KIT-888S-R10:
Realtek ALC888S 7.1 Channel HD Audio peripheral board, RoHS
- CF-1150SA-R10
Special cooler kit for LGA1150, high-performance compatible, 95W
- CF-1150SB-R11
Special cooler kit for LGA1150, high-performance compatible, 65W
- CF-1150SC-R20
Special cooler kit for LGA1150, 1U chassis compatible, 65W
- CF-1150SE-R11
Special cooler kit for LGA1150, high-performance compatible, 95W
Jumpers Setting and Connectors
| LABEL |
FUNCTION |
| J_ATX_AT1 |
AT/ATX power mode setting |
| SW_BIOS1_1 |
BIOS selection switch |
| J_CMOS1 |
Clear CMOS jumper |
| J_FLASH1 |
Flash descriptor security override jumper |
| CPU12V1 |
ATX CPU 12V power connector |
| J_AUDIO1 |
Audio connector |
| BAT1 |
RTC battery connector |
| CHASSIS1 |
Chassis intrusion connector |
CHA_DIMM0, CHA_DIMM1
CHB_DIMM0, CHB_DIMM1 |
DDR4 DIMM slots |
| DIO1 |
Digital I/O connector |
| DBG_SPI1 |
EC debug connector |
| CPU_FAN1, SYS_FAN1 |
Fan connectors |
| JSPI1 |
Flash SPI ROM connector |
| JEC1 |
Flash EC ROM connector |
| F_PANEL1 |
Front panel connector |
| I2C1 |
I2C connector |
| LED_LAN1 |
LAN1 link LED connector |
| LED_LAN2 |
LAN2 link LED connector |
| M2_A1 |
M.2 A-key slot |
| M2_B1 |
M.2 B-key slot |
| M2_M1 |
M.2 M-key slot (on solder side) |
| PWR_SW1 |
On-board power switch |
| COM1, COM2 |
RS-232 serial port connectors |
| COM3, COM4 |
RS-422/485 serial port connectors |
| S_ATA3, S_ATA4, S_ATA5, S_ATA6 |
SATA 6Gb/s connectors |
| SMB1 |
SMBus connector |
| SIM1 |
SIM card slot |
| JUSB3, JUSB4, JUSB5 |
Internal USB 2.0 connectors |
| USB1 |
Internal USB 3.2 Gen 1 connector (Type-A) |
| JUSB3-1 |
Internal USB 3.2 Gen 1 connector |
| LAN1, LAN2 |
External 2.5GbE RJ-45 connectors |
| HDMI1 |
External HDMI connector |
| CN1, CN2 |
External USB 3.2 Gen 1 connectors |
| CON1 |
External USB 3.2 Gen 2 connector |
| J_ATX_AT1: AT/ATX Power Mode Setting |
| PIN NO. |
DESCRIPTION |
| Short 1 – 2 |
ATX Power Mode (default) |
| Short 2 – 3 |
AT Power Mode |
| SW_BIOS1_1: BIOS Selection Switch |
| PIN NO. |
DESCRIPTION |
| Short A – B |
BIOS1: four PCIe x1 slots (default) |
| Short B – C |
BIOS2: one PCIe x4 slot |
| J_CMOS1: Clear CMOS Jumper |
| Status |
DESCRIPTION |
| NC |
Keep CMOS Setup (Normal Operation) |
| Press |
Clear CMOS Setup |
| J_FLASH1: Flash Descriptor Security Override Jumper |
| PIN NO. |
DESCRIPTION |
| Short 1-2 |
Disabled (default) |
| Short 2-3 |
Enabled |
| USB Power SW: USB Power Setting |
| USB Power SW |
DESCRIPTION |
| +5V DUAL |
Power is provided in S3/S4 sleep state (default) |
| +5V |
Power is not provided in S3/S4 sleep state |
| Use the USB Power SW BIOS options to configure whether to provide power to the corresponding USB connector(s) when the system is in S3/S4 sleep state. This option is valid only when the above Power Saving Function (ERP) BIOS option is disabled. |
| CPU12V1: ATX CPU 12V Power Connector |
| PIN NO. |
DESCRIPTION |
PIN NO. |
DESCRIPTION |
| 1 |
GND |
5 |
+12V |
| 2 |
GND |
6 |
+12V |
| 3 |
GND |
7 |
+12V |
| 4 |
GND |
8 |
+12V |
| J_AUDIO1 : Internal Audio Connector for IEI Audio Module |
| PIN NO. |
DESCRIPTION |
PIN NO. |
DESCRIPTION |
| 1 |
HDA_SYNC |
2 |
HDA_BIT_CLK |
| 3 |
HDA_SDOUT |
4 |
HDA_SPKR |
| 5 |
HDA_SDIN |
6 |
HDA_RST# |
| 7 |
HDA_VCC |
8 |
HDA_GND |
| 9 |
HDA_+12V |
10 |
HDA_GND |
| BAT1: RTC Battery Connector |
| PIN NO. |
DESCRIPTION |
PIN NO. |
DESCRIPTION |
| 1 |
VBATT |
2 |
GND |
| CHASSIS1: Chassis Intrusion Connector |
| PIN NO. |
DESCRIPTION |
PIN NO. |
DESCRIPTION |
| 1 |
+3.3VSB |
2 |
CHASSIS_OPEN |
| DIO1 : Digital Input/Output Connector |
| PIN NO. |
DESCRIPTION |
PIN NO. |
DESCRIPTION |
| 1 |
GND |
2 |
VCC |
| 3 |
Output 5 |
4 |
Output 4 |
| 5 |
Output 3 |
6 |
Output 2 |
| 7 |
Output 1 |
8 |
Output 0 |
| 9 |
Input 5 |
10 |
Input 4 |
| 11 |
Input 3 |
12 |
Input 2 |
| 13 |
Input 1 |
14 |
Input 0 |
| DBG_SPI1: EC Debug Connector |
| PIN NO. |
DESCRIPTION |
PIN NO. |
DESCRIPTION |
| 1 |
NC |
4 |
EDICLK |
| 2 |
EDICS |
5 |
EDIDI |
| 3 |
EDIDO |
6 |
GND |
| CPU_FAN1, SYS_FAN: CPU/System Fan Connector |
| PIN NO. |
DESCRIPTION |
PIN NO. |
DESCRIPTION |
| 1 |
GND |
3 |
FANIO |
| 2 |
+12V |
4 |
PWM |
| JSPI1: Flash SPI ROM Connector |
| PIN NO. |
DESCRIPTION |
PIN NO. |
DESCRIPTION |
| 1 |
+V3.3M_SPI_CON |
4 |
SPI_CLK_SW |
| 2 |
SPI_CS |
5 |
SPI_SI_SW |
| 3 |
SPI_SO_SW |
6 |
GND |
| JEC1: Flash EC ROM Connector |
| PIN NO. |
DESCRIPTION |
PIN NO. |
DESCRIPTION |
| 1 |
FSCE# |
2 |
VCC |
| 3 |
FMISO |
4 |
NC |
| 5 |
EC_DET_FLASH |
6 |
FSCK |
| 7 |
GND |
8 |
FMOSI |
| F_PANEL1: Front Panel Connector |
|
PIN |
DESCRIPTION |
PIN |
DESCRIPTION |
|
| PWR LED |
1 |
PWR_LED+ |
2 |
BEEP_PWR |
SPKR |
| 3 |
NC |
4 |
NC |
| 5 |
PWR_LED- |
6 |
NC |
| PWR BTN |
7 |
PWR_BTN+ |
8 |
PC_BEEP |
| 9 |
PWR_BTN- |
10 |
NC |
|
| HDD LED |
11 |
HDD_LED+ |
12 |
Reset+ |
RESET |
| 13 |
HDD_LED- |
14 |
Reset- |
| I2C1: I2C Connector |
| PIN NO. |
DESCRIPTION |
PIN NO. |
DESCRIPTION |
| 1 |
GND |
3 |
I2C_CLK |
| 2 |
I2C_DATA |
4 |
+5V |
| LED_LAN1: LAN1 Link LED Connector |
| PIN |
DESCRIPTION |
PIN |
DESCRIPTION |
| 1 |
+3.3V |
2 |
LAN1_LED_LNK#_ACT |
| LED_LAN2: LAN2 Link LED Connector |
| PIN |
DESCRIPTION |
PIN |
DESCRIPTION |
| 1 |
+3.3V |
2 |
LAN2_LED_LNK#_ACT |
| COM1, COM2: RS-232 Serial Port Connectors |
| PIN NO. |
DESCRIPTION |
PIN NO. |
DESCRIPTION |
| 1 |
DCD |
2 |
DSR |
| 3 |
RXD |
4 |
RTS |
| 5 |
TXD |
6 |
CTS |
| 7 |
DTR |
8 |
RI |
| 9 |
GND |
10 |
GND |
| COM3, COM4: RS-422/428 Serial Port Connectors |
| PIN NO. |
DESCRIPTION |
PIN NO. |
DESCRIPTION |
| 1 |
RXD422- |
3 |
TXD422+/TXD485+ |
| 2 |
RXD422+ |
4 |
TXD422-/TXD485- |
| S_ATA3, S_ATA4, S_ATA5, S_ATA6: SATA 6Gb/s Connectors |
| PIN NO. |
DESCRIPTION |
PIN NO. |
DESCRIPTION |
| 1 |
GND |
5 |
SATA_RX‐ |
| 2 |
SATA_TX+ |
6 |
SATA RX+ |
| 3 |
SATA_TX‐ |
7 |
GND |
| 4 |
GND |
8 |
N/C |
| SMB1: SM Bus Connector |
| PIN NO. |
DESCRIPTION |
PIN NO. |
DESCRIPTION |
| 1 |
GND |
3 |
SMB_CLK |
| 2 |
SMB_DATA |
4 |
+5V |
| JUSB3, JUSB4, JUSB5: Internal USB 2.0 Connectors |
| PIN NO. |
DESCRIPTION |
PIN NO. |
DESCRIPTION |
| 1 |
VCC |
2 |
GND |
| 3 |
USB_DATA- |
4 |
USB_DATA+ |
| 5 |
USB_DATA+ |
6 |
USB_DATA- |
| 7 |
GND |
8 |
VCC |
| USB1: Internal USB 3.2 Gen 1 Connector (Type-A) |
| PIN NO. |
DESCRIPTION |
PIN NO. |
DESCRIPTION |
| 1 |
VCC |
6 |
USB3_RX+ |
| 2 |
USB_DATA- |
7 |
GND |
| 3 |
USB_DATA+ |
8 |
USB3_TX- |
| 4 |
GND |
9 |
USB3_TX+ |
| 5 |
USB3_RX- |
|
| JUSB3-1: Internal USB 3.2 Gen 1 Connector |
| PIN NO. |
DESCRIPTION |
PIN NO. |
DESCRIPTION |
| 1 |
VCC |
11 |
USB_DATA+ |
| 2 |
USB_RX- |
12 |
USB_ DATA- |
| 3 |
USB_RX+ |
13 |
GND |
| 4 |
GND |
14 |
USB3_TX+ |
| 5 |
USB3_TX- |
15 |
USB3_ TX- |
| 6 |
USB3_TX+ |
16 |
GND |
| 7 |
GND |
17 |
USB3_RX+ |
| 8 |
USB3_DATA- |
18 |
USB3_RX- |
| 9 |
USB3_DATA+ |
19 |
VCC |
| 10 |
NC |
|
| M2_A1: M.2 A-key Slot |
| PIN NO. |
DESCRIPTION |
PIN NO. |
DESCRIPTION |
| 1 |
GND |
2 |
+3.3V |
| 3 |
USB+ |
4 |
+3.3V |
| 5 |
USB- |
6 |
NC |
| 7 |
GND |
8 |
Module Key |
| 9 |
Module Key |
10 |
Module Key |
| 11 |
Module Key |
12 |
Module Key |
| 13 |
Module Key |
14 |
Module Key |
| 15 |
Module Key |
16 |
NC |
| 17 |
NC |
18 |
GND |
| 19 |
NC |
20 |
NC |
| 21 |
NC |
22 |
NC |
| 23 |
GND |
24 |
GND |
| 25 |
NC |
26 |
NC |
| 27 |
NC |
28 |
NC |
| 29 |
GND |
30 |
GND |
| 31 |
NC |
32 |
NC |
| 33 |
GND |
34 |
NC |
| 35 |
PCIE_TXP1 |
36 |
GND |
| 37 |
PCIE_TXN1 |
38 |
NC |
| 39 |
GND |
40 |
NC |
| 41 |
PCIE_RXP1 |
42 |
NC |
| 43 |
PCIE_RXN1 |
44 |
NC |
| 45 |
GND |
46 |
NC |
| 47 |
PCIE_CLKP0 |
48 |
NC |
| 49 |
PCIE_CLKN0 |
50 |
NC |
| 51 |
GND |
52 |
PLT_RST |
| 53 |
CLKREQ0# |
54 |
Pull up +3.3V |
| 55 |
PCIE_WAKE |
56 |
Pull up +3.3V |
| 57 |
GND |
58 |
M2_DAT |
| 59 |
PCIE_TXP2 |
60 |
M2_CLK |
| 61 |
PCIE_TXN2 |
62 |
NC |
| 63 |
GND |
64 |
NC |
| 65 |
PCIE_RXP2 |
66 |
M2_RST |
| 67 |
PCIE_RXN2 |
68 |
CLKREQ0# |
| 69 |
GND |
70 |
PCIE_WAKE |
| 71 |
PCIE_CLKP1 |
72 |
+3.3V |
| 73 |
PCIE_CLKN1 |
74 |
+3.3V |
| 75 |
GND |
|
| M2_M1: M.2 M-key Slot |
| PIN NO. |
DESCRIPTION |
PIN NO. |
DESCRIPTION |
| 1 |
GND |
2 |
+3.3V |
| 3 |
GND |
4 |
+3.3V |
| 5 |
PCIE_RXN3 |
6 |
N/C |
| 7 |
PCIE_RXP3 |
8 |
N/C |
| 9 |
GND |
10 |
DAS/DSS# |
| 11 |
PCIE_TXN3 |
12 |
+3.3V |
| 13 |
PCIE_TXP3 |
14 |
+3.3V |
| 15 |
GND |
16 |
+3.3V |
| 17 |
PCIE_RXN2 |
18 |
+3.3V |
| 19 |
PCIE_RXP2 |
20 |
N/C |
| 21 |
GND |
22 |
N/C |
| 23 |
PCIE_TXN2 |
24 |
N/C |
| 25 |
PCIE_TXP2 |
26 |
N/C |
| 27 |
GND |
28 |
N/C |
| 29 |
PCIE_RXN1 |
30 |
N/C |
| 31 |
PCIE_RXP1 |
32 |
N/C |
| 33 |
GND |
34 |
N/C |
| 35 |
PCIE_TXN1 |
36 |
N/C |
| 37 |
PCIE_TXP1 |
38 |
DEVSLP |
| 39 |
GND |
40 |
N/C |
| 41 |
PCIE_RXN0 |
42 |
N/C |
| 43 |
PCIE_RXP0 |
44 |
N/C |
| 45 |
GND |
46 |
N/C |
| 47 |
PCIE_TXN0 |
48 |
N/C |
| 49 |
PCIE_TXP0 |
50 |
PERST# |
| 51 |
GND |
52 |
CLKREQ# |
| 53 |
REFCLKN |
54 |
PEWAKE |
| 55 |
REFCLKP |
56 |
N/C |
| 57 |
GND |
58 |
N/C |
| 59 |
Module Key |
60 |
Module Key |
| 61 |
Module Key |
62 |
Module Key |
| 63 |
Module Key |
64 |
Module Key |
| 65 |
Module Key |
66 |
Module Key |
| 67 |
NC |
68 |
SUSCLK |
| 69 |
PEDET |
70 |
+3.3V |
| 71 |
GND |
72 |
+3.3V |
| 73 |
GND |
74 |
+3.3V |
| 75 |
GND |
|
| M2_B1: M.2 B-key Slot |
| PIN NO. |
DESCRIPTION |
PIN NO. |
DESCRIPTION |
| 1 |
CONFIG_3 |
2 |
+3.3V |
| 3 |
GND |
4 |
+3.3V |
| 5 |
GND |
6 |
NC |
| 7 |
USB+ |
8 |
NC |
| 9 |
USB- |
10 |
NC |
| 11 |
GND |
12 |
Module Key |
| 13 |
Module Key |
14 |
Module Key |
| 15 |
Module Key |
16 |
Module Key |
| 17 |
Module Key |
18 |
Module Key |
| 19 |
Module Key |
20 |
NC |
| 21 |
CONFIG_0 |
22 |
NC |
| 23 |
PCH_WAKE_N |
24 |
NC |
| 25 |
NC |
26 |
NC |
| 27 |
GND |
28 |
NC |
| 29 |
PCIE_RXN1 |
30 |
SIM_RST |
| 31 |
PCIE_RXP1 |
32 |
SIM_CLK |
| 33 |
GND |
34 |
SIM_IO |
| 35 |
PCIE_TXN1 |
36 |
SIM_VCC |
| 37 |
PCIE_TXP1 |
38 |
NC |
| 39 |
GND |
40 |
NC |
| 41 |
PCIE_RXP0 |
42 |
NC |
| 43 |
PCIE_RXN0 |
44 |
NC |
| 45 |
GND |
46 |
NC |
| 47 |
PCIE_TXN0 |
48 |
NC |
| 49 |
PCIE_TXP0 |
50 |
M2_RST |
| 51 |
GND |
52 |
CLKREQ0# |
| 53 |
PCIE_CLKN0 |
54 |
PCH_WAKE_N |
| 55 |
PCIE_CLKP0 |
56 |
NC |
| 57 |
GND |
58 |
NC |
| 59 |
NC |
60 |
NC |
| 61 |
NC |
62 |
NC |
| 63 |
NC |
64 |
NC |
| 65 |
NC |
66 |
NC |
| 67 |
M2_RST |
68 |
NC |
| 69 |
M2BCONF |
70 |
+3.3V |
| 71 |
GND |
72 |
+3.3V |
| 73 |
GND |
74 |
+3.3V |
| 75 |
GND |
|
| SIM1: SIM Card Slot |
| PIN NO. |
DESCRIPTION |
PIN NO. |
DESCRIPTION |
| C1 |
SIM_VCC |
C5 |
GND |
| C2 |
SIM_RST |
C6 |
NC |
| C3 |
SIM_CLOCK |
C7 |
SIM_IO |
| LAN1, LAN2: External 2.5GbE RJ-45 Connectors |
| PIN NO. |
DESCRIPTION |
PIN NO. |
DESCRIPTION |
| 1 |
MDIA3- |
5 |
MDIA1+ |
| 2 |
MDIA3+ |
6 |
MDIA2+ |
| 3. |
MDIA2- |
7 |
MDIA0- |
| 4. |
MDIA1- |
8 |
MDIA0+ |
| HDMI1: External HDMI Connector |
| PIN NO. |
DESCRIPTION |
PIN NO. |
DESCRIPTION |
| 21 |
HDMI_DATA2 |
31 |
GND |
| 22 |
GND |
32 |
HDMI_CLK# |
| 23 |
HDMI_DATA2# |
33 |
N/C |
| 24 |
HDMI_DATA1 |
34 |
N/C |
| 25 |
GND |
35 |
HDMI_SCL |
| 26 |
HDMI_DATA1# |
36 |
HDMI_SDA |
| 27 |
HDMI_DATA0 |
37 |
GND |
| 28 |
GND |
38 |
+5V |
| 29 |
HDMI_DATA0# |
39 |
HDMI_HPD |
| 30 |
HDMI_CLK |
|
| CN1, CN2: External USB 3.2 Gen 1 Connectors (Type-A) |
| PIN NO. |
DESCRIPTION |
PIN NO. |
DESCRIPTION |
| 1 |
VCC |
6 |
USB3_RX+ |
| 2 |
USB_DATA- |
7 |
GND |
| 3 |
USB_DATA+ |
8 |
USB3_TX- |
| 4 |
GND |
9 |
USB3_TX+ |
| 5 |
USB3_RX- |
|
| CON1: External USB 3.2 Gen 2 Connector (Type-C) |
| PIN NO. |
DESCRIPTION |
PIN NO. |
DESCRIPTION |
| A1 |
GND |
B12 |
GND |
| A2 |
TX1+ |
B11 |
RX1+ |
| A3 |
TX1- |
B10 |
RX1- |
| A4 |
VBUS |
B9 |
VBUS |
| A5 |
CC1 |
B8 |
SBU2 |
| A6 |
D+ |
B7 |
NC |
| A7 |
D- |
B6 |
NC |
| A8 |
SBU1 |
B5 |
VCONN |
| A9 |
VBUS |
B4 |
VBUS |
| A10 |
RX2- |
B3 |
TX2- |
| A11 |
RX2+ |
B2 |
TX2+ |
| A12 |
GND |
B1 |
GND |
Board Layout: Jumper and Connector Locations
Documents / Resources
References
