iBoard IB-082C Running Board Side Step Bars
- Part Number: IB-082C&H
- Fastener Sizes: 6mm, 8mm, 10mm, 12mm, 14mm
- Tightening Torque (ft-lbs): 6-7, 16-18, 31-32, 56-58, 92-94
Product Usage Instructions
Step 1: Driver Side Front InstallationStart by removing the front body mount nut and washer. Use pliers or a crescent wrench to hold the bolt while loosening the nut.
Step 2: Driver Front Mounting Bracket InstallationLoosely attach the Driver Front Mounting Bracket using the factory nut and washer. Ensure the factory rubber bushing and other components are in place.
Step 5: Step Bar Installation
- Select a Slider and two M8X1.25-35mm Carriage Bolts.
- Install the Carriage Bolts in the Slider.
- Slide the Slider with carriage bolts onto the Step Bar.
- Repeat for the other slider and Step Bar.
- Attach the Step Bar with Sliders to the installed mounting brackets. Secure using Large Flat Washers, Nylon Lock Nuts, and Sliders. Do not fully tighten at this time.
Frequently Asked Questions
- Q: Can I install the step bars alone without assistance?
- A: While assistance is recommended, the installation can be done alone with careful following of the provided instructions.
- Q: What tools are required for installation?
- A: Basic tools such as pliers, wrenches, and possibly a socket set may be needed for proper installation.
Product Information
READ INSTRUCTIONS CAREFULLY BEFORE START ING INSTALLATION. REMOVE CONTENTS FROM BOX AND VERIFY ALL PARTS ARE PRESENT. ASSISTANCE IS RECOMMENDED.
- BODY FRAME MOUNT
- NO DRILLING REQUIRED
| Fastener Size | Tightening Torque (ft-lbs) | Required |
| 6mm | 6-7 | X |
| 8mm | 16-18 | √ |
| 10mm | 31-32 | X |
| 12mm | 56-58 | X |
| 14mm | 92-94 | X |
PART LIST
Hardware Package
Hardware Package A (For Bracket Installation)
| Item | QTY | Description | Item | QTY | Description |
| 1# | 6 | M8X1.25-30mm Hex Bolts | 3# | 6 | M8 Lock Washers |
| 2# | 8 | M8 Large Flat Washers | 4# | 2 | M8 Hex Nuts |
Hardware Package B (For Stainless Steel Step Bar Installation)
| Item | QTY | Description | Item | QTY | Description |
| 1# | 8 | M8X1.25-35mm Carriage Bolts | 3# | 8 | M8 Nylon Lock Nuts |
| 2# | 8 | M8 Large Flat Washers | 4# | 4 | Sliders (Packed with Step Bars) |
Installation Instruction
STEP 1
Start installation from the driver side front of the vehicle. Re-move front body mount nut and washer located underside of vehicle. NOTE: Use a pair of pliers or a crescent wrench to hold the bolt as you loosen the nut, (Fig 1).
STEP 2
Loosely attach Driver Front Mounting Bracket (DFM) using the factory nut and washer. NOTE: Keep factory rubber bushing and other factory body mount components in place (Fig 1).
STEP 3
Move toward the rear of the vehicle. Repeat Steps 1-2 to install the Driver Rear Mounting Bracket (DRM), (Fig 2).
STEP 4
Locate the (2) factory threaded holes in the side panel by the rear body mounting location and attach the Driver Rear Support Bracket (DRS) to these factory holes using the included (2) M8X1.25-30mm Hex Bolts, (2) M8 Lock Washers, and (2) M8 Large Flat Washers, (Fig 3).
Attach opposite side of Driver Rear Support Bracket (DRS) to Driver Rear Mounting Bracket (DRM) using the included (1) M8X1.25-30mm Hex Bolt, (1) M8 Lock Washer, (1) M8X1.25 Hex Nut, and (2) M8 Large Flat Washers, (Figs 3 & 4). Do not fully tighten at this time.
STEP 5
Once all (2) Driver side mounting brackets are installed, then proceed to the Step Bar installation. (Figs 5 & 6)
- Select (1) Slider and (2) M8X1.25-35mm Carriage Bolts;
- Install (2) M8X1.25-35mm Carriage Bolts in (1) Slider.
- Slide the Slider (with carriage bolts) to the Step Bar.
- Repeat to install the other (1) slider to the step bar.
- Attach the Step Bar (with the Sliders) onto the installed mounting brackets. Position the Sliders to the installed brack-ets. Secure the Step Bar to the installed Brackets by using (4) M8 Large Flat Washers and (4) M8 Nylon Lock Nuts and (2) Sliders, (Fig 6). Do not fully tighten hardware at this time.
Note: The Sliders are packed with the Step Bars. Level and adjust the Step Bar and fully tighten all hardware. Repeat Steps 1-5 for the other side Step Bar installation. The installation is completed!!!
Attention
Do periodic inspections to the installation to make sure that all hardware is secure and tight. In order to protect your bars/boards, please use mild soap/non-abrasive products for cleaning only.
Customer Support: info@iboardauto.com
Documents / Resources
 |
iBoard IB-082C Running Board Side Step Bars [pdf] Installation Guide IB-082C, IB-082H, IB-082C Running Board Side Step Bars, IB-082C, Running Board Side Step Bars, Board Side Step Bars, Side Step Bars, Step Bars |