HYTRONIK Bluetooth Receiver Node – DALI Version Instruction Manual
Technical Specifications
| Product type |  DALI Digitial Receiver Node (Flush mount) |
| Mains voltage | 220~240VAC 50/60Hz |
| Rated load | Max.100mA, 50 devices |
| Stand-by power | <0.5W |
| Operation frequency | 2.4 GHz – 2.483 GHz |
| Transmission power | 4 dBm |
| Range (Typical) | 10 ~ 30m |
| Protocol | 5.0 SIG Mesh |
| Operation temperature | Ta: -20°C ~ +45°C |
| Case temperature Max.) | Tc: +75°C |
| Storage temperature | -20°C ~ +60°C |
| Max. relative humidity | 20 ~ 90% |
| IP rating | IP20 |
| Impulse withstand oltage | 2.5KV |
| Duty type | S1 |
| Insulation material | PTI material group IIIa |
| Glow wire | level 3, 850°C |
| Protection | Built-in protection provide |
| Insulation | Class II Pollution degree 2 |
| EMC standard (EMC) | EN55015, EN61547, EN61000-3-2, EN61000-3-3 |
| Safety standard (LVD) | IEC 61058-1, EN 61058-1, IEC 61058-1-2 EN 61058-1-2, AS/NZS 61058.1 |
| Radio Equipment (RED) | EN300 328, EN301489-1, EN301489-17, EN62479 |
Download the App
Free App for set-up and commissioning
5.0 SIG mesh
iOS 10.0 or later
Android 5.0 or later
Web app/platform:
iot.koolmesh.com
Dimming Interface Operation Notes
Switch-Dim
The provided Switch-Dim interface allows for a simple dimming method using commercially available non-latching (momentary) wall switches. Detailed Push switch configurations can be set on Koolmesh app.
| Switch Function | Action | Descriptions |
| Push switch | Short press (<1 second) Short press has to be longer than 0.1s, or it will be invalid. |
– Turn on/off – Recall a scene – Turn on only – Exit manual mode – Turn off only – Do nothing |
| Double push | – Turn on only – Exit manual mode – Turn off only – Do nothing – Recall a scene |
|
| Long press (≥1 second) | – Dimming – Colour tuning – Do nothing |
|
| Simulate sensor | / | – Upgrade a normal on/off motion sensor to a Bluetooth controlled motion sensor |
Installation
Warnings:
- Installation must be carried out by a qualified engineer in accordance with local regulations.
- Disconnect power supply before installing.
- Ensure environmental conditions are suitable for electronic equipment.
Wire Preparation
Wiring Diagram
Additional Information / Documents
- To learn more about detailed product features/functions, please refer to www.hytronik.com/download ->knowledge ->Introduction of App Scenes and Product Functions
- Regarding precautions for Bluetooth product installation and operation, please kindly refer to www.hytronik.com/download ->knowledge ->Bluetooth Products – Precautions for Product Installation and Operation
- Data sheet is subject to change without notice. Please always refer to the most recent release on www.hytronik.com/products/bluetooth technology ->Bluetooth Sensor ->Receiver Nodes
- Regarding Hytronik standard guarantee policy, please refer to www.hytronik.com/download ->knowledge ->Hytronik Standard Guarantee Policy.
Documents / Resources
 | Bluetooth Receiver Node - DALI Version |
References
- User Manualmanual.tools
Published: January 4, 2022
How to increase the range of the bluetooth watch
Как да се увеличи обхвата на блутут часовника
Как да се увеличи обхвата на блутут часовника
How can I increase the Bluetooth range of the Hytronik HBTD8200D/F receiver node?
The Hytronik HBTD8200D/F Bluetooth Receiver Node has a typical range of 10 to 30 meters. Because this device uses Bluetooth 5.0 SIG Mesh technology, the best way to increase the overall range is to add more Bluetooth mesh nodes to your installation.
In a mesh network, each node acts as a repeater that passes the signal to the next device, effectively extending the control distance far beyond the 30-meter limit of a single unit. To optimize the existing range, ensure the following:
If you are specifically referring to a Bluetooth wearable (watch) used to control the system, its range is limited by its internal antenna, and adding more receiver nodes to the mesh network is the primary method to ensure the watch can communicate with the system from further away.
Read the full Q&A page