HYTRONIK HBIR31 Bluetooth PIR Standalone Motion Sensor Owner’s Manual
PIR Standalone Motion Sensor with 
5.0 SIG Mesh
Product Description
HBIR31 is a Bluetooth PIR standalone motion sensor with 80mA DALI power supply built in, which can control up to 40 LED drivers. It is ideal for typical indoor applications such as office, classroom, healthcare and other commercial areas. With Bluetooth wireless mesh networking, it makes communication between luminaries much easier without time-consuming hard wiring, which eventually saves costs for projects (especially for retrot upgrade projects!). Meanwhile, simple device setup and commissioning can be done via 
app
App Features
Hardware Features
Technical Specifcations
Bluetooth Transceiver
Sensor Data
* For more details of detection range, please refer to “detection pattern” section.
Input & Output Characteristics
Safety & EMC
Environment
*IP54 (facial part) only for lens of standard,/R,/H
Mechanical Structure & Dimensions
- Ceiling (drill hole Ø 66~68mm).
- Carefully prise off the Back Caps.
- Make connections to the pluggable terminal blocks.
- Secure the cables with screws for better stability.Three types of Back Caps are available (Standard, HA08 , and HA08/S).
- Fit detection blind (if required).
- Fit desired lens, clip fascia to body (this step is not applicable for /UH).
- Bend back springs and Insert into ceiling.
*The standard back cap is designed for the installation of two cables. HA08 is a high back cap, allows cables to exit upwards. HA08/S is designed for sideways cable exits.
Wiring Diagram
Wire Preparation
Big and small silicon gasket used to make IP54 degree protection when HBIR31 series device mounted into HA09 housing for ceiling mount
Note: The small silicon water-proof gasket is not suitable for HBIR29/W and HBIR29/UH The Big silicon water-proof gasket is not suitable for HBIR29/W
Placement Guide and Typical Range
Smart Phone to Device Range
The smart device with the App installed will have a typical range of 10m, but varies from device to device. During commissioning, the installer will need to be in range of the devices when searching for devices to add to the network.
Once the devices have been added to the network via the App, the devices will start communicating within the wireless mesh. This means that once the network is complete, all devices are accessible from the smart device when in a 20m range of a single point.
Detection Pattern & Optional Accessories
Dimming Interface Operation Notes
Switch-Dim
The provided Switch-Dim interface allows for a simple dimming method using commercially available non-latching (momentary) wall switches.
Detailed Push switch congurations can be set on Koolmesh app.
Additional Information / Documents
- To learn more about detailed product features/funcvtions, please refer to
www.hytronik.com/download ->knowledge ->Introduction of App Scenes and Product Functions - Regarding precautions for Bluetooth product installation and operation, please kindly refer to
www.hytronik.com/download ->knowledge ->Bluetooth Products – Precautions for Product Installation and Operation - Regarding precautions for PIR Sensors installation and operation, please kindly refer to
www.hytronik.com/download ->knowledge ->PIR Sensors – Precautions for Product Installation and Operation - Data sheet is subject to change without notice. Please always refer to the most recent release on
www.hytronik.com/products/bluetooth technology ->Bluetooth Sensors - Regarding Hytronik standard guarantee policy, please refer to
www.hytronik.com/download ->knowledge ->Hytronik Standard Guarantee Policy
Subject to change without notice.
Read More About This Manual & Download PDF:
Documents / Resources
 |
HYTRONIK HBIR31 Bluetooth PIR Standalone Motion Sensor [pdf] Owner's Manual HBIR31, HBIR31 Bluetooth PIR Standalone Motion Sensor, Bluetooth PIR Standalone Motion Sensor, PIR Standalone Motion Sensor, Standalone Motion Sensor, Motion Sensor, Sensor |
