HyperGear Wireless Earbuds User Manual

HyperGear Wireless Earbuds

User Manual

WARRANTY INFORMATION

HyperGear warranties this product against all defects in material and/or workmanship under normal use for a period of ONE (1) YEAR from the date of purchase by the original purchaser.

Contact info@myhypergear.com to submit a warranty claim. Proof of purchase is required.

IMPORTANT

Read all safety instructions and warnings prior to using this product. Improper use and failure to follow safety guidelines could result in damage, excess heat, toxic fumes, fire, explosion, electrical shock or other hazards causing serious and/or fatal injury and/or property damage and not the manufacturer’s responsibility. The user is responsible for maintaining this product with care for maximum use.

  1. Do not store in a depleted state. Battery cells may be damaged. Charge your unit at least once every 3 months even when not in use.
  2. Avoid excessively loud listening levels, especially for extended periods of time, as it can cause permanent hearing damage.
  3. Maintain volume levels that will allow you to hear sound around you and be alerted to potentially hazardous situations.
  4. Do not store at extreme temperatures (below 40˚ F or above 90˚ F)
  5. Recharge your device with the included Micro USB charging cable or a certified 3rd party cable and a 2A charging adapter. Standard cables and adapters may charge the battery too slowly and damage/overheat the battery or cause a fire hazard.
  6. This product is not a toy – keep this product  and all component parts out of the reach of children.
  7. Do not attempt to modify, disassemble, or repair this product.
  8. Avoid excessive drops, bumps, abrasions, and rough handling of the cords and cables.
  9. If the unit has dents, punctures, tears, deformities, or corrosion, discontinue use and contact the manufacturer or dispose of in an appropriate method.
  10. Under any circumstances, if you find this product rapidly increasing in temperature, emitting odor, or demonstrating an abnormal phenomenon, discontinue use immediately.
  11. In dry air conditions, you may feel a static shock when using the earphones. Do not be alarmed, simply allow the static build-up to discharge.
  12. Disposal of unit in the garbage is unlawful under state and federal environmental laws and regulations.
  13. Unit is not waterproof. Do not clean with harsh chemicals, soaps or detergents or submerge.

Prop 65: This product may contain chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.

TROUBLESHOOTING

Q: My earphones will not turn on.
A: Your earphones may be low or out of power. Connect to a power source. The LED light will show whether it is charging. Fully charge before use.

Q: My earphones will not pair.
A: Check that your earphones are turned on.
A: Check that your source device has the Bluetooth function activated then follow its pairing instructions.
A: Check that your earphones are in Pairing Mode, and are not automatically pairing to another device.
A: Your earphones may be out of range. Move closer to your source device.
A: The battery power may be too low on your earphones, source device, or both. Fully charge as needed.

Q: I have already paired with my device, but I cannot hear any music.
A: Your earphones may be out of range. Move closer to your source device.
A: The volume on your source device may be muted. Check that your device is playing at audible levels.
A: Adjust the volume level directly on your mobile device. Note: Some apps and programs have their own sound settings separate from the general device settings. Make sure to adjust those as well, as needed.
A: The battery power may be too low on your earphones, source device, or both. Fully charge as needed.
A: Try a “soft reset” by powering your earphones off then on.
A: Try re-pairing. First delete the earphones from your list of discovered Bluetooth devices selecting “Forget this Device” for iOs/Apple, or “Unpair” for Android, then follow our pairing instructions.

Q: The sound is too low/too high/poor quality.
A: Your earphones may be out of range. Move closer to your source device.
A: Adjust the volume level directly on your mobile device. Note: Some apps and programs have their own sound settings separate from the general device settings. Make sure to adjust those as well, as needed.
A: Move away from or turn off nearby devices that may be generating interference, such as another Bluetooth device or wireless router.
A: Try turning off Wi-Fi on your source device to improve audio quality.
A: Closing non-essential applications on your source device may improve audio quality. Running multiple applications can reduce the amount of internal resources available to transmit audio clearly.

For additional customer support and technical assistance, please email info@myhypergear.com

INSTRUCTION

Fully charge your earphones before first use.

How to Charge
Using the included Micro USB charging cable to connect your earphones to a USB power source (such as a USB wall adapter, computer USB port, etc.).

Once plugged in, the LED power indicator will light up RED. When charging is complete, the LED will turn OFF (approximately 2 hours).

How to Power On/Power Off

ON: Press and Hold MFB, until you hear “Power On”
OFF: Press and Hold MFB until you hear “Power Off”

Thank you for purchasing the HyperGear Wireless Earbuds!

Please read this manual thoroughly and keep it for future reference.

Visit www.myhypergear.com to learn more about your new earphones or other HyperGear products.

HyperGear Wireless Earbuds User Manual – Optimized PDF
HyperGear Wireless Earbuds User Manual – Original PDF

References

Questions and answers

Helpful product questions tied to this manual. Each item links to the full Q&A page.

Browse all questions about this manual

Questions & Answers

Use this section to ask about setup, compatibility, troubleshooting, or anything missing from this manual.

  1. Ok so my right earbud is only working my left one won’t work I already disconnected and unpaired them to my (iPhone 12) and still only my right one works. Can y’all please help me out!

    Hayden asks Ok so my right earbud is only working my left one won’t work I already disconnected and unpaired them to my (iPhone 12) and still only my right one works. Can y’all please help me out!
    Manuals+ clarified question
    Question

    Why is only my right HyperGear earbud working and how can I fix the left one?

    Answer

    If your left earbud is not producing sound even after unpairing and reconnecting, please try the following troubleshooting steps based on the HyperGear manual:

    • Check Power and Charging: Ensure the left earbud is fully charged. Place it in the charging case or connect it to the Micro USB cable. The LED should light up RED while charging and turn OFF when complete. If the LED does not light up, check for debris on the charging contacts.
    • Perform a Soft Reset: Power the earbuds off completely by pressing and holding the Multi-Function Button (MFB) until you hear "Power Off," then turn them back on.
    • Check for Sync Issues: Sometimes earbuds lose their connection to each other. Try turning both earbuds off, then turn them both on simultaneously to allow them to re-sync before pairing them to your iPhone.
    • Verify Volume Settings: Ensure that the balance settings on your iPhone 12 are centered (Settings > Accessibility > Audio/Visual > Balance) and that the volume is turned up on the device.

    If the left earbud still fails to turn on or play audio after these steps, it may have a hardware defect. Since HyperGear offers a ONE (1) YEAR warranty, you should contact info@myhypergear.com with your proof of purchase to submit a claim.

  2. Hello, I was given a HYPERGEAR Model 14316 wireless headphones. I lost the user manual or the instructions and now I have the inconvenience that I do not know if the left earphone does not charge or does not pair with the right one and I do not know how to solve it.
    The truth is that I only hear for the right.
    Could someone send me the instructions for use? Maybe there it says it is possible to reset them.
    Thank you

    Hola, me regalaron unos auriculares inalambricos HYPERGEAR Modelo14316. Perdí el manual de uso o las instrucciones y ahora tengo el inconveniente de que no sé si es que el auricular izquierdo no se carga o no se empareja con el derecho y no sé como solucionarlo.
    Lo cierto es que solo oigo por el derecho.
    Alguien podría enviarme las instrucciones de uso? Tal vez allí diga se es posible resetearlos.
    Muchas gracias

    PABLO CERCHIARI asks <em><strong>Hello, I was given a HYPERGEAR Model 14316 wireless headphones. I lost the user manual or the instructions and now I have the inconvenience that I do not know if the left earphone does not charge or does not pair with the right one and I do not know how to solve it.
    The truth is that I only hear for the right.
    Could someone send me the instructions for use? Maybe there it says it is possible to reset them.
    Thank you</strong></em>
    Hola, me regalaron unos auriculares inalambricos HYPERGEAR Modelo14316. Perdí el manual de uso o las instrucciones y ahora tengo el inconveniente de que no sé si es que el auricular izquierdo no se carga o no se empareja con el derecho y no sé como solucionarlo.
    Lo cierto es que solo oigo por el derecho.
    Alguien podría enviarme las instrucciones de uso? Tal vez allí diga se es posible resetearlos.
    Muchas gracias
    Manuals+ clarified question
    Question

    How do I troubleshoot my HyperGear 14316 earbuds when only the right side works and the left side won't charge or pair?

    Answer

    To resolve issues where only one earbud is working or the left earbud is not pairing/charging, please follow these troubleshooting steps based on the HyperGear manual:

    • Check Charging: Ensure the left earbud is making proper contact with the charging pins. Use the included Micro USB cable and a 2A charging adapter. The LED indicator should light up RED when charging and turn off when fully charged (approx. 2 hours).
    • Perform a Soft Reset: Power the earbuds off by pressing and holding the Multi-Function Button (MFB) until you hear "Power Off," then power them back on.
    • Refresh the Bluetooth Connection:
      1. Go to your device's Bluetooth settings and select "Forget this Device" (iOS) or "Unpair" (Android) for your HyperGear earbuds.
      2. Turn off Bluetooth on your phone.
      3. Power the earbuds on and ensure they are in pairing mode.
      4. Turn Bluetooth back on and attempt to re-pair the device.
    • Check for Interference: Move away from wireless routers or other Bluetooth devices that might be causing signal drops between the two earbuds.

    If the left earbud still does not show a red LED when connected to power, it may be defective. Since HyperGear offers a one-year warranty, you can contact their support at info@myhypergear.com for further assistance.

  3. Same problem listed above. Left earbud does not pair.

    Phil Hulbig asks Same problem listed above. Left earbud does not pair.
    Manuals+ clarified question
    Question

    How do I fix the left earbud not pairing on my HyperGear Wireless Earbuds?

    Answer

    If your left earbud is not pairing or syncing correctly, please try the following troubleshooting steps based on the HyperGear manual:

    • Perform a Soft Reset: Power your earbuds off completely, then power them back on by pressing and holding the Multi-Function Button (MFB).
    • Clear Bluetooth History: On your source device (phone or tablet), go to your Bluetooth settings and select "Forget this Device" (iOS) or "Unpair" (Android) for the HyperGear earbuds.
    • Re-pair from Scratch: Ensure both earbuds are fully charged. Turn them on and follow the pairing instructions to reconnect them to your device.
    • Check Battery Levels: Low battery can cause pairing failures. Ensure the earbuds have been charged for approximately 2 hours (the RED LED will turn OFF when fully charged).
    • Check for Interference: Move away from other Bluetooth devices or wireless routers that might be causing signal interference.

    If the left earbud still fails to function, it may be a hardware defect. HyperGear offers a ONE (1) YEAR warranty. You can contact their support team at info@myhypergear.com with your proof of purchase to submit a claim.

  4. Same for me listed above, except it’s my right earbud

    Asia Figueroa asks Same for me listed above, except it’s my right earbud
    Manuals+ clarified question
    Question

    Why is my right earbud not working or pairing?

    Answer

    If your right earbud is not functioning correctly, please try the following troubleshooting steps based on the HyperGear manual:

    • Perform a Soft Reset: Power your earbuds off completely and then turn them back on.
    • Check Power Levels: Ensure the earbuds are fully charged. Connect them to a power source using the Micro USB cable; the LED will turn red while charging and turn off when complete.
    • Reset Bluetooth Pairing: On your mobile device, go to Bluetooth settings and select "Forget this Device" (iOS) or "Unpair" (Android). Turn your Bluetooth off and back on, then follow the pairing instructions to reconnect.
    • Check for Interference: Move away from other wireless routers or Bluetooth devices that might be causing signal interference.
    • Clean the Contacts: Ensure there is no debris on the charging pins or the earbud itself that might be preventing a full charge or proper operation.

    If the right earbud remains unresponsive, it may have a hardware defect. HyperGear offers a one-year warranty. You can contact their support team at info@myhypergear.com with your proof of purchase to submit a claim.

Ask a Question

Ask about setup, compatibility, troubleshooting, or anything missing from this manual. Name and email are optional.