HPRT S2 Portable Thermal Label Printer
Product Specifications
- Model: S2
- Power Source: Battery
- Charging Method: DC adapter or USB port
- Connectivity: Bluetooth
- Print Type: Thermal Printing
- Print Head Safety: Overheating prevention
Packing List
Note: The packing items are actually based on the order.
Using Guide
Power Button Status
- Hold down for 2 seconds to ON/OFF
- Lighting: Standby / Charging completed
- Slow flash: Charging
- Fast flash: Supplies near end, cover open, Firmware updating, low battery, the print head is overheated
Charging
- Use it for the first time after purchase
- Recommended to use after full charge
- Charge via DC adapter or computer USB porta
LED Indicator Definitions
In use
- Normal： always on
- Exception： flashes slowly，
view tips in the APP. - Charging process
- Charge normally： flashes slowly
- Full of anomalies： flashes quickly
- Battery charged： always on
Description
- Power Button
- Cover Opening Button
- Upper Cover
- Paper Roll Sleeve
- Paper Tearing Knife
- USB Interface
Warning
The paper tearing knife has sharp edges and should not be touched.
Download APP
Scan the QR code below and install the App.
Connect the device
Download Hereprint – APP, turn on Bluetooth on your phone, enter the APP, click Add Device, and connect by searching Bluetooth.
APP Setting
Simple Operation APP Setting
You can view information such as remaining power, firmware version in device management.
Replace Supplies
- With reference to figure 1, Pull the cover opening button down and open the top cover, remove the paper roll sleeve.
- When replacing supplies, place the supplies in reference to the direction shown in figure 2.
- Close the top cover after loading paper roll sleeve. Please make sure both sides click into place.
- When changing supplies , do not touch the print head in case of injury caused by overheating.
Safety Precautions
Battery Overheating
Battery Management and Precautions
When charging is completed, please unplug the USB cable.
To avoid fire, do not charge at high temperature (e.g. sweating rooms, bonfire nearby, etc.).
Charger Attention
Print Head Management and Precautions
There may be damage to the print head due to improper charging.
We recommend not to use printer in high humidity or dusty areas.
Burn Hazard
Print Head Overheating
After printing, do not touch the print head directly in case of injury caused by overheating.
Charging Port Damage
Charging Precautions
Please gently insert or unplug the USB cable to prevent excessive damage to the charging port.
FCC
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
Warning: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Radiation Exposure Statement
The device has been evaluated to meet general RF exposure requirement.
The device can be used in portable exposure condition without restriction.
Frequently Asked Questions (FAQ)
Q: Can I charge the device in high-temperature environments?
A: It is recommended not to charge the device in high-temperature conditions to avoid potential fire hazards.
Q: How do I connect the device to the app?
A: Turn on Bluetooth on your phone, open the app, click Add Device, and search for Bluetooth to connect.
Documents / Resources
 |
HPRT S2 Portable Thermal Label Printer [pdf] User Guide 2DT24AU, 2AUTE-2DT24AU, 2AUTE2DT24AU, S2 Portable Thermal Label Printer, S2, Portable Thermal Label Printer, Thermal Label Printer, Label Printer |
