HORMANN FIT 1 BiSecur Radio Internal Push 
Button Instruction Manual

About these instructions

• Read through the instructions carefully.
• Keep these instructions in a safe place.

Important note for avoiding material damage and personnel injury

High exertion of force

Safety instructions

WARNING

• Make sure that the radio internal push buttons are kept away from children and can only be used by people who have been instructed on how the remote- control system functions!
• If the door has only one safety equipment, only operate the radio internal push button if you are within sight of the door!
• Drive or walk through the door openings of remote-controlled systems only when the door is in the Open end-of-travel position!
• Never stand in the door’s area of travel.
• Note that accidentally pressing a button on the hand transmitter can result in door travel.
• Pay attention that no persons or objects are in the system’s area of travel when teaching in the radio system.

CAUTION

• Ensure that the remote-controlled operation of equipment does not result in danger to persons or objects or that these risks are covered by safety equipment.
• Observe the manufacturer information for the remote-controlled devices.
• The unintentional activation of machines must not be possible.

• If there is no separate entrance, perform changes and extensions of radio systems while standing in the facility.
• After programming or extending the radio system, you have to perform a function check.
• Local conditions may affect the range of the radio system.

Scope of delivery

• Radio internal push button FIT 1 / 4 BiSecur
• 2 × 1.5 V battery, type: AAA (LR03), alkali-manganese
• Fixing material
• Operating instructions

Product description (see Figure 1 )

1. LED, multicolour
2. Transmitter button
3. Housing
4. Mounting plate
5. Battery

Fitting

• Prior to fitting, verify that the radio signal can reach the system or the equipment at the selected fitting site.
  – Determine the best orientation, by trial and error, if required.
• Direct fitting on metal will affect the range.
  – Fit at a distance of 2 – 3 cm.

• See sectio 5.1

• See section 5.2

• Use clean, lint-free and non-perfumed cleaning cloths.
• Only use suitable cleaning agents, e.g. benzine.
• Do not use lipid-restoring household cleaners or glass cleaners.

• Do not touch the gluing surface.
• Quickly glue the mounting plate in the desired position.
  Adjusting the position subsequently is only partially possible.

Initial start-up

WARNING

• Use only this battery type: 2 × 1.5 V, type: AAA (LR03), alkali-manganese
• Remove the battery from the radio internal push button if it is out of use for a long period of time.

Operation

• Press the transmitter button whose radio code you want to transmit.

• Press and hold the transmitter button until the LED flashes alternately in red and blue and the desired function is performed.

• Press the transmitter button a second time.

Learning and inheriting / transmitting a radio code

• See warning in section 2.2.

1. Hold the hand transmitter A to the right of the radio internal push button.
2. Press and hold the hand transmitter button whose radio code is to be inherited.
   – The LED is illuminated blue for 2 seconds and then goes out.
   – After 5 seconds, the LED alternates flashing in red and blue.
   – The hand transmitter sends the radio code.
3. Press and hold the transmitter button that should learn the radio code.
   – The LED is illuminated blue for 2 seconds and then goes out.
   – The LED will flash slowly in blue.
   – If the radio code is recognised, the LED flashes quickly in blue.
   – After 2 seconds, the LED goes out.
4. Release the hand transmitter button and the transmitter button.
   The radio code of the hand transmitter button has been taught in to the transmitter button .

Reset

1. Open the radio internal push button housing.
2. Remove the battery for 10 seconds.
3. Press a transmitter button and keep it pressed.
4. Insert the battery.
   – The LED slowly flashes in blue for 4 seconds.
   – The LED flashes rapidly in blue for 2 seconds.
   – The LED is illuminated blue for a long time.
5. Release the transmitter button.
   All radio codes are newly assigned .
6. Close the radio internal push button housing.

1. Carry out steps 1 – 4 of the device reset
2. Continue to keep the transmitter button pressed.
   – The LED slowly flashes in red for 4 seconds.
   – The LED flashes rapidly in red for 2 seconds.
   – The LED is illuminated red for a long time.
3. Release the transmitter button.
   The fixed code 868 MHz has been set .
4. Close the radio internal push button housing.

LED display

Dismantling and disposal

Dispose of the packaging sorted by materials

Electrical and electronic devices must be returned to the appropriate recycling facilities.

Dispose of the batteries separately. Each consumer is legally required to leave batteries with a collection point in their community, their district, or with a trader.

Technical data

 

Documents / Resources

HORMANN FIT 1 BiSecur Radio Internal Push Button [pdf] Instruction Manual FIT 1 BiSecur, FIT 4 BiSecur, FIT 1 BiSecur Radio Internal Push Button, FIT 1 BiSecur, Radio Internal Push Button, Internal Push Button, Push Button, Button

References

• User Manual