QuikDial™ 4x Outlet Digital Tap Timer

User Guide
www.holmanindustries.com.au

PRODUCT CODE: CO6004

Overview

Main Components

1.  ZONE 1 outlet
2. ZONE 2 outlet
3. ZONE 3 outlet
4. ZONE 4 outletEach outlet is 20mm BSP with 12mm snap‑on connection included
5. 20mm BSP tap nut inlet
6. Tap connection locking nut
7. Display
8. ON/OFF
9. Main dial
10.  Battery compartment: Requires 2× AA alkaline batteries only (not included)

Overview (continued)
Additional Functions

 Inactivity on your QuikDial Tap Timer controls for 6 seconds will return to the default system mode displaying the current time
 Removing the AA batteries will reset all clock and schedule settings
To reset your QuikDial Tap Timer, remove the batteries and twist the main dial until the display is completely blank
 For use with cold water only

Specifications

Interval scheduling	1, 2, 3, 6 or 12 hours, or 1‑7 days
Watering duration	1‑30 minutes
Working pressure	30‑1200 kPa
Maximum flow rate	25 L/min
Connections	20mm BSP inlet / 20mm BSP outlet
Working temperature	3°C to 50°C
Batteries	2× AA alkaline (not included)

Setup

Battery Installation

1.  Install 2× 1.5v AA alkaline batteries into your QuikDial Tap Timer, as indicated in the battery compartment [a]

After installing the batteries, the display will flash and your QuikDial will make clicking noises as part of the start‑up phase
Once the start‑up process is complete, the clock will display as follows, with the time separator flashing [b] and the battery indicated as full [c]

Setup Process
Your QuickDial features a quick setup process across 5 key steps.
Use the main dial to scroll through the main menu for each step

Setup (continued)
Zone

This process is to select which zones will be watered as part of your schedule

1. Turn the main dial to select ZONE [a] in the main menu
   
2. Press the main dial to edit zones
     The zone selector [b] will flash around ZONE 1 and indicate as ON [c]
3. Press the main dial to toggle ZONE 1 ON or OFF as desired
   When a zone is turned OFF, the zone number [d] will disappear and the OFF indicator [e] will be displayed
   The zone selector [f] will remain flashing
   
4. Turn the main dial to the next zone
   The zone selector [g] will flash around the next zone and indicate as OFF [h]
5.  Press the main dial to toggle the zone ON or OFF as desired
6. Repeat steps 4-5 for the remaining zones
7. After ZONE 4 has been set to ON or OFF, turn the main dial one more step
   The zone selectors will flash around all zones [i], and the status of each zone will be indicated by their respective numbers being present (ON) [j] or missing (OFF) [k]
8. To confirm your zone settings, press the main dial
     Alternatively, to go back and change your zone settings, turn the dial another step and repeat steps 3-7
   Once your zones are confirmed, ZONE will flash in the main menu [l] and the active zones will be shown [m]

Setup (continued)
Set Clock

This process is to set the system clock for your QuikDial
Your QuikDial system time is always in 24‑hour format (military time)

1. Turn the main dial to select SET CLOCK [a] in the main menu
   
2.  Press the main dial. The current hour [b] will begin flashing
   
3.  Turn the main dial to adjust the hour to the current time
4.  Press the main dial to confirm the current hour. The current minute will begin flashing [c]
5. Turn the main dial to adjust the minute to the current time
6. Press the main dial to confirm the current minute
     SET CLOCK will flash again in the main menu [d], to indicate the system time [e] has been set
   

Setup (continued)
Start Time

  This process is to set the START TIME for watering of your active zones
This START TIME is applied to all zones, but is only active on the zones that have been toggled ON in the previous instructions
Refer back to Zone for more information on enabling or disabling zones

1. Turn the main dial to  select START TIME [a]in the main menu
   
    This will display the current START TIME [b]. By default, this is set to 08:00 (8:00 am)
2.  Press the main dial. The START TIME hour [c] will begin flashing
   
3.  Turn the main dial to adjust the hour to the desired START TIME
4. Press the main dial to confirm the hour. The START TIME minute will begin flashing [c]
5.  Turn the main dial to adjust the minute to the desired START TIME
   Setup (continued)
   Start Time (continued)
6. Press the main dial to confirm the minute

START TIME in the main menu [d] will flash again, to indicate it has been set [e]

How Long (Watering Duration)

This process is to set the watering duration of your active zones
  This duration is applied to all zones, but is only active on the zones that have been toggled ON in the previous instructions
Refer back to Zone for more information on enabling or disabling zones

1. Turn the main dial to select HOW LONG [a] in the main menu
   
   This will display the current watering duration [b]. By default, this is set to 5 minutes
2. Press the main dial. The duration in minutes [c] will begin flashing

Setup (continued)
How Long (continued)

3. Turn the main dial to adjust duration as desired
4. Press the main dial to confirm the duration

HOW LONG in the main menu [d] will flash again, to indicate the duration has been set [e]

How Often (Watering Interval)

  This process is to set the interval time between watering sessions of your active zones
This interval is applied to all zones, but is only active on the zones that have been toggled ON in the previous instructions
  Refer back to Zone for more information on enabling or disabling zones

1. Turn the main dial to select HOW OFTEN [a] in the main menu

  This will display the current watering interval [b]. By default, this is set to 1 day 

Setup (continued)
How Long (continued)
2. Press the main dial. The interval [c] will begin flashing

3. Turn the main dial to adjust the interval length in DAYS from 1 to 7
For shorter watering intervals in HOURS [d], turn the main dial beyond 7 days. The interval will now show as 1 hour 

  Keep turning the main dial to adjust the watering interval in HOURS
  Hourly watering intervals are available in 1, 2, 3, 6 or 12 hours
To go back to setting the interval in DAYS [e], keep turning the dial beyond  2 hours. The intervalwill return to 1 day

4. With the desired interval time showing, press the main dial to confirm

  HOW OFTEN in the main menu [f] will flash again, to indicate the interval has been set [g]

Operation

Automatic Watering

1. For automatic watering, ensure ZONE, SET CLOCK, START TIME, HOW LONG and HOW OFTEN have all been set correctly as per the previous instructions
2. After a period of inactivity on your QuikDial controls, the  set watering schedule will beactive in the background as per your confirmed settings
     In this state, your QuikDial display will cycle between the current time [a] and the amount of time left before your NEXT watering session [b]
3. When the current interval time [b] lapses, the zones will start watering in sequential order
     During watering, the sprinkler animation [c] will be active, the current zone [d] will flash, and the remaining watering time [e] will also flash as it counts down
     Additional zones scheduled for watering will also show [f]

Operation (continued)
Manual Watering

1. For manual (instant) watering, press ON/OFF
2. The zone selector [a] will flash. Twist the main dial to select a zone
   
3. Press the main dial to water immediately for the pre‑set duration [b]. By default, this is 10 minutes
     During watering, the sprinkler animation [c] will be active, and the current zone [d] will flash
4. Once watering, the remainingtime [e] will also flash to indicate it is adjustable
5. Turn the main dial to adjust the watering time as desired
   The minimum watering time is 1 minute
   The maximum watering time is 31 minutes
6. After a short period of time, the remaining watering time will stop flashing to indicate it has been set
     To stop watering before the remaining time has lapsed, press ON/OFF and your QuikDial will return to the default display
     If the remaining time stops flashing before  you were able to adjust it, press ON/OFF to stop watering, and restartthe manual watering process from Step 1

Maintenance

Cold Weather
Your QuikDial should be removed from the tap and stored away during winter
Keep your tap timer out of freezing conditions as this can damage internal components Batteries
  Remove batteries from your QuikDial during periods of non‑use–this will erase all settings
Battery leakage can cause corrosion and damage to your QuikDial
Do not mix old and new batteries
 Do not use rechargeable batteries

Neet halp? Just ask!

The Holman website has a host of additional information on features. Head to support.holmanindustries.com.au for more tips, tricks and support content.
If you still need help, feel free to email our friendly Customer Service team at support@holmanindustries.com.au or call at 08 9416 9999.

https://support.holmanindustries.com.au/?=qr

We really appreciate having you as a customer, and
would like to say thank you for choosing us.
We recommend registering your new product on our website. This will ensure we have
a copy of your purchase and activate an extended warranty. Keep up to date to with
relevant product information and special offers available through our newsletter.
www.holmanindustries.com.au/product-registration/

For the #SMARYGARDENER

Copyright © 2021 Holman Industries

Documents / Resources

HOLMAN CO6004 QuikDial 4x Outlet Digital Tap Timer [pdf] User Guide CO6004, QuikDial 4x Outlet Digital Tap Timer, CO6004 QuikDial 4x Outlet Digital Tap Timer

References

• User Manual