IM-120 Multiple Entry Input Module
Cov ntaub ntawv khoom siv thiab cov lus qhia siv rau cov khoom siv nkag
Cov ntaub ntawv khoom
Input Module (IM-120) yog ib feem ntawm kev ruaj ntseg system uas tso cai rau kev sib txuas ntawm ntau yam khoom siv xws li sensors, keyboards, thiab detectors. Lub module yog tsim los nruab rau hauv qhov chaw qhuav thiab tuaj nrog ntau yam khoom siv xws li kho cov screws, spacers, thiab diodes. Cov cuab yeej siv tau nrog lub kaw lus (ENCR-10) uas suav nrog kev faib hluav taws xob thiab ntawmamper hloov, uas tuaj yeem yuav nyias.
Cheebtsam
- Input Module (IM-120)
- Cov Lus Qhia Ceev
- Drilling Template
- Open Source Software – MIT License
- Kho Screw x12
- Spacer x 6
- Diode x 2
Specifications
- Version: 1.02 Lus Askiv EN 101.00.IM-120 V1.02A
- FCC Cov Ntaub Ntawv Ua Raws Cai: 20
- Cov lus qhia ntxiv: 21
- Tsis lees paub: 21
- Daim ntawv ceeb toom Copyright: 21
- Open Source License: 21 MIT Open Source License
- Kev sib txuas fais fab: 9
- RS-485 Kev sib txuas: 10
- Kev sib txuas ntawm Relay: 11
- Saib xyuas kev sib txuas lus nkag: 12
- Tamper Kev sib txuas: 13
Cov lus qhia siv
Kev teeb tsa
Ua ntej kev teeb tsa, thov nyeem cov lus qhia kev nyab xeeb kom tsis txhob raug mob rau koj tus kheej thiab lwm tus, thiab tiv thaiv kev puas tsuaj ntawm cov khoom. Cov cuab yeej yuav tsum tsis txhob muab tso rau hauv qhov chaw uas muaj tshav ntuj ncaj qha, noo noo, plua plav, soot, lossis roj xau. Tsis tas li ntawd, nws yuav tsum tsis txhob muab tso rau hauv qhov chaw uas muaj cua sov los ntawm lub tshuab hluav taws xob los yog cuam tshuam los ntawm xov tooj cua zaus.
Kev sib txuas fais fab
Kev sib txuas hluav taws xob yog tsim los ntawm kev siv fais fab adapter, plugs
thiab ib lub qhov hluav taws xob. Xyuas kom meej tias cov khoom no tsis yog
puas los yog xoob. Tsis txhob khoov lossis ua rau lub zog qaum.
RS-485 Kev sib txuas
Kev sib txuas RS-485 yog rau kev sib txuas lus nrog kev ruaj ntseg. Xyuas kom tseeb tias cov xaim txuas tau zoo thiab tsis muaj cov xov hlau uas tuaj yeem ua rau luv luv. Siv cov hlua khi hlua khi hlua khi kom txo qis kev cuam tshuam.
Txuas Txuas
Kev sib txuas relay yog rau kev sib txuas cov khoom siv xws li sirens, tswb, lossis teeb. Xyuas kom tseeb tias cov xaim txuas tau zoo thiab tsis muaj cov xov hlau uas tuaj yeem ua rau luv luv.
Supervised Input Connection
Kev saib xyuas cov tswv yim sib txuas yog rau kev sib txuas cov cuab yeej xws li qhov rooj sensors lossis qhov rais sensors. Xyuas kom tseeb tias cov xaim txuas tau zoo thiab tsis muaj cov xov hlau uas tuaj yeem ua rau luv luv.
Tampyog Connection
Qhov tamper kev sib txuas yog rau kev sib txuas ntawmamper hloov mus kuaj yog tias lub cuab yeej tau tampered nrog. Xyuas kom tseeb tias cov xaim txuas tau zoo thiab tsis muaj cov xov hlau uas tuaj yeem ua rau luv luv.
Siv lub Input Module nrog lub enclosure
Yog tias siv lub kaw lus, teeb tsa cov ntsia hlau kho rau lub kaw lus (inch: 4 hli, ntev: 25 hli) x 4, kho cov ntsia hlau rau lub cuab yeej (inch: 3 hli, ntev: 5 hli) x 6, thiab kho cov ntsia hlau rau cov khoom siv. fais fab mov cable (inch: 3 mm, ntev: 8 mm) x 1. Xa mus rau "Siv lub Input Module nrog rau Enclosure" seem ntawm phau ntawv qhia kom ntxaws installation cov lus qhia.
Cov ntaub ntawv kev nyab xeeb
Thov nyeem cov lus qhia kev nyab xeeb no ua ntej koj siv cov khoom los tiv thaiv kev raug mob rau koj tus kheej thiab lwm tus thiab tiv thaiv kev puas tsuaj. Lo lus 'cov khoom' hauv phau ntawv no yog hais txog cov khoom thiab txhua yam khoom uas muab nrog cov khoom.
Kev qhia ntawv icons
Ceeb toom: Lub cim no qhia txog cov xwm txheej uas tuaj yeem ua rau tuag lossis raug mob hnyav.
Ceev faj: Cov cim no qhia txog cov xwm txheej uas yuav ua rau muaj kev raug mob me ntsis lossis kev puas tsuaj ntawm vaj tse.
Nco tseg: Lub cim no qhia txog cov ntawv sau lossis cov ntaub ntawv ntxiv.
Ceeb toom
Kev teeb tsa
- Tsis txhob nruab los yog kho cov khoom arbitrarily.
- Qhov no yuav ua rau hluav taws xob poob siab, hluav taws kub, lossis khoom puas tsuaj.
- Kev puas tsuaj los ntawm kev hloov kho lossis tsis ua raws li cov lus qhia kev teeb tsa tuaj yeem ua rau lub chaw tsim khoom tsis lees paub.
- Tsis txhob nruab cov khoom nyob rau hauv ib qho chaw uas muaj tshav ntuj ncaj qha, noo noo, plua plav, soot, los yog roj av.
- Qhov no yuav ua rau hluav taws xob poob lossis hluav taws.
- Tsis txhob nruab cov khoom hauv qhov chaw uas muaj cua sov los ntawm lub tshuab hluav taws xob.
- Qhov no yuav ua rau hluav taws kub vim overheating.
- Nruab cov khoom hauv qhov chaw qhuav.
- Cov av noo thiab kua yuav ua rau hluav taws xob poob lossis cov khoom puas tsuaj.
- Tsis txhob nruab cov khoom hauv qhov chaw uas nws yuav cuam tshuam los ntawm xov tooj cua zaus.
- Qhov no yuav ua rau hluav taws kub lossis khoom puas tsuaj.
Kev ua haujlwm
- Khaws cov khoom kom qhuav.
- Cov av noo thiab kua yuav ua rau hluav taws xob poob siab, hluav taws kub, lossis khoom puas tsuaj.
- Tsis txhob siv cov khoom siv hluav taws xob puas, cov ntsaws ruaj ruaj, lossis cov qhov hluav taws xob xoob xoob.
- Kev sib txuas tsis ruaj yuav ua rau hluav taws xob poob lossis hluav taws.
- Tsis txhob khoov lossis ua rau lub zog qaum.
- Qhov no yuav ua rau hluav taws xob poob lossis hluav taws.
Ceev faj
- Tsis txhob nruab cov khoom nyob rau hauv lub hnub ncaj qha los yog UV teeb.
- Qhov no yuav ua rau cov khoom puas, ua haujlwm tsis zoo, tsis muaj xim, lossis deformation.
- Tsis txhob nruab lub fais fab cable rau hauv qhov chaw uas tib neeg hla dhau.
- Qhov no yuav ua rau raug mob lossis cov khoom puas tsuaj.
- Tsis txhob nruab cov khoom nyob ze cov khoom sib nqus, xws li cov hlau nplaum, TV, saib (tshwj xeeb tshaj yog CRT), lossis hais lus.
- Cov khoom yuav malfunction.
- Tsis txhob tso cov khoom pov tseg lossis ua rau muaj kev cuam tshuam rau cov khoom.
- Cov khoom yuav malfunction.
- Tsis txhob cuam tshuam cov khoom siv hluav taws xob thaum txhim kho lub firmware ntawm cov khoom.
- Cov khoom yuav malfunction.
- Tsis txhob nias cov nyees khawm ntawm cov khoom los ntawm kev quab yuam lossis tsis txhob nias lawv nrog lub cuab yeej ntse.
- Cov khoom yuav malfunction.
- Tsis txhob khaws koj cov khoom nyob rau hauv qhov chaw kub heev los yog txias heev. Nws raug nquahu kom siv cov khoom ntawm qhov kub ntawm -20 ° C txog 60 ° C.
- Cov khoom yuav malfunction.
- Thaum ntxuav cov khoom, nco ntsoov cov hauv qab no.
- So cov khoom nrog ib daim phuam huv thiab qhuav.
- Yog tias koj yuav tsum tau ntxuav cov khoom, moisten daim ntaub los yog so nrog cov dej cawv kom zoo thiab maj mam
ntxuav txhua qhov chaw uas raug pom nrog rau tus ntiv tes sensor. Siv dej cawv (muaj 70% Isopropyl cawv) thiab a
huv, tsis-abrasive ntaub zoo li lo ntsiab muag so. - Tsis txhob siv cov kua ncaj qha rau saum npoo ntawm cov khoom.
- Tsis txhob siv cov khoom rau lwm yam tshaj li qhov nws xav siv.
- Cov khoom yuav malfunction.
Taw qhia
Cheebtsam
Accessory
Koj tuaj yeem siv qhov Input Module nrog lub kaw lus (ENCR-10). Lub thawv ntim khoom yog muag nyias, thiab koj tuaj yeem nruab ob lub tswv yim Modules hauv ib lub thawv. Lub kaw lus muaj xws li lub hwj chim xwm txheej LED board, lub hwj chim faib board, fais fab mov, thiab tampua. Txhawm rau kawm paub yuav ua li cas rau nruab Input Module hauv lub thawv, xa mus rau Siv lub Input Module nrog lub enclosure.
- Tsis muaj qhov siab zoo rau kev txhim kho ENCR-10 ntawm phab ntsa. Nruab nws rau qhov chaw nyab xeeb thiab yooj yim rau koj siv.
- Txhim kho cov ntsia hlau rau lub qhov rooj, cov cuab yeej, thiab cov khoom siv hluav taws xob muaj nyob rau hauv pob ENCR-10. Siv txhua tus ntsia hlau kom raug raws li cov ntsiab lus hauv qab no.
- Kho cov ntsia hlau rau lub qhov rooj (inch: 4 mm, ntev: 25 mm) x 4
- Txhim kho cov ntsia hlau rau lub cuab yeej (inch: 3 hli, ntev: 5 hli) x 6
- Txhim kho screws rau lub hwj huam mov cable (inch: 3 hli, ntev: 8 hli) x 1
Lub npe thiab kev ua haujlwm ntawm txhua qhov chaw
| Tsis muaj. | Lub npe |
| 1 | RESET khawm |
| 2 | INIT khawm |
| 3 | Saib xyuas cov tswv yim (9, 10, 11) kev sib txuas |
| 4 | Saib xyuas cov tswv yim (6, 7, 8) kev sib txuas |
| 5 | Relay 1 kev sib txuas |
| 6 | AUX IN (0, 1) thiab Tampyog kev sib txuas |
| 7 | RS-485 terminating kuj hloov |
| 8 | RS-485 kev twb kev txuas |
| 9 | Kev sib txuas fais fab (DC 12-24V) |
| 10 | Relay 0 kev sib txuas |
| 11 | Saib xyuas cov tswv yim (3, 4, 5) kev sib txuas |
| 12 | Saib xyuas cov tswv yim (0, 1, 2) kev sib txuas |
Nco tseg: Nias thiab tuav lub pob INIT rau 2 vib nas this lossis ntev dua los pib lub Input Module tam sim no txuas nrog lub cuab yeej thiab txuas mus rau lwm lub cuab yeej.
Qhov taw qhia LED
Koj tuaj yeem tshawb xyuas cov xwm txheej ntawm lub cuab yeej los ntawm cov xim ntawm LED qhov taw qhia.
| Yam khoom | LED | xwm txheej |
| Hwj chim | Khoom liab | Fais fab rau |
|
STATUS |
Khoom ntsuab | Txuas nrog lub rooj sib tham ruaj ntseg |
| Khoom xiav | Disconnected los ntawm tus tswv ntaus ntawv | |
| Khoom liab | Upgrading lub firmware | |
| Khoom daj | RS-485 kev sib txuas lus yuam kev vim qhov sib txawv encryption key lossis OSDP pob ntawv poob | |
| Lub ntuj xiav | Txuas nrog yam tsis muaj kev sib tham ruaj ntseg | |
| Blinking ntsuab | Tos rau qhov kawg cov tswv yim los pib dua kev teeb tsa | |
| Khoom ntsuab | Kev teeb tsa pib ua tiav | |
| SUPERVISED Input (0 – 11) | Khoom liab | Tau txais lub teeb liab input |
| RELAY (0, 1) | Khoom liab | Relay ua haujlwm |
| RS-485 TX | Blinking txiv kab ntxwv | Kev lees paub rau lub dav hlau RS-485 data |
| RS-485 RX | Blinking ntsuab | Kev lees paub rau lub dav hlau RS-485 data |
| AUX IN (0, 1) | Khoom txiv kab ntxwv | Tau txais AUX teeb liab |
| TAMPER | Khoom txiv kab ntxwv | Tampua haujlwm |
Installation example
Lub Input Module muab tus cwj pwm cuam tshuam tam sim los ntawm kev txuas mus rau BioStar 2 rau kev kuaj pom cov khoom siv hauv lub sijhawm tiag tiag thiab nws ua haujlwm relay lossis txuag cov cav rau cov khoom nkag thaum nws raug txiav tawm ntawm tus tswv ntaus ntawv. Lub Input Module txhawb 12-channel saib xyuas cov tswv yim, 2-channel relay, 2-channel AUX input, thiab 1-channel tamper input mus ntes cov xwm txheej, xws li 1-channel RS-485, disconnection, luv luv, on, los yog tawm rau kev sib txuas lus nrog tus tswv ntaus ntawv.
Kev teeb tsa
Nco tseg: Txhawm rau kawm paub yuav ua li cas rau nruab Input Module nyob rau hauv lub enclosure, xa mus rau Siv lub Input Module nrog lub enclosure.
- Txhim kho lub spacer ntawm txoj hauj lwm rau mount Input Module siv ib tug fixing ntsia hlau.
- Txhim kho cov khoom nyob rau sab saum toj ntawm qhov chaw ruaj khov ruaj khov siv cov ntsia hlau kho.
Kev sib txuas fais fab
Nco tseg:
- Nco ntsoov siv lub zog sib cais rau cov cuab yeej tswj kev nkag mus thiab cov tswv yim Module.
- Siv cov khoom siv hluav taws xob kom raug (12 VDC, 130 mA lossis 24 VDC, 82 mA).
RS-485 Kev sib txuas
Koj tuaj yeem txuas lub Input Module rau ib lub cuab yeej tswv.
Nco tseg:
- Siv AWG24 twisted khub nrog tsawg dua 1.2 km ntev rau RS-485 cable.
- Yog tias txuas nrog RS-485 daisy saw, txuas qhov kev txiav tawm qhov hluav taws xob (120 Ω) mus rau ob qho kawg ntawm daisy saw txuas. Yog tias txuas nrog txoj kab nruab nrab, theem teeb liab yuav me dua thiab kev sib txuas lus yuav ua rau tsis zoo. Nco ntsoov txuas nws mus rau ob qho kawg ntawm daisy saw txuas. Teem lub termination hloov (TERM) rau ON rau Input Module.
Txuas Txuas
Lub relay ntawm Input Module tuaj yeem tswj lub qhov rooj xauv thiab lub tswb. Txuas lub relay li NC (Zoo li Kaw) lossis TSIS MUAJ (Nquag Qhib) los ntawm kev xa mus rau cov lus qhia kev teeb tsa ntawm cov khoom sib txuas.
- Fail Safe Xauv: Txhawm rau siv Fail Safe Lock, txuas NC relay raws li qhia hauv daim duab hauv qab no. Muaj ib txwm muaj tam sim no ntws los ntawm cov relay rau Fail Safe Lock. Thaum lub relay qhib, thaiv cov dej ntws tam sim no, lub qhov rooj yuav qhib. Yog hais tias lub hwj huam mov rau cov khoom raug txiav tawm vim lub hwj chim tsis ua hauj lwm los yog lwm yam, lub qhov rooj yuav qhib.
- Fail Secure Xauv: Txhawm rau siv Fail Secure Lock, txuas TSIS TAU relay raws li qhia hauv daim duab hauv qab no. Muaj ib txwm tsis muaj tam sim no ntws los ntawm cov relay rau Fail Secure Lock. Thaum cov dej ntws tam sim no tau qhib los ntawm relay, lub qhov rooj yuav qhib. Yog hais tias lub hwj huam mov rau cov khoom raug txiav tawm vim lub hwj chim tsis ua hauj lwm los yog lwm yam, lub qhov rooj yuav xauv.
- Txuas lub diode mus rau ob qho kawg ntawm lub hwj chim tawm tswv yim raws li qhia hauv daim duab hauv qab no thaum txhim kho lub deadbolt lossis lub qhov rooj tawm tsam. Nco ntsoov txuas lub Cathode (kev taw qhia mus rau kab txaij) mus rau + ib feem ntawm lub zog thaum ua tib zoo saib xyuas cov kev taw qhia ntawm lub diode.
- Tsis txhob txuas lub relay ntawm Input Module nyob rau hauv duplicate rau lub cuab yeej txuas nrog lub relay chaw nres nkoj ntawm tus tswv ntaus ntawv.
Supervised Input Connection
Koj tuaj yeem txuas lub ntsuas hluav taws xob, hluav taws kub sensor, kev ruaj ntseg sensor, qhov rooj sensor, tawm khawm, lossis lwm yam SUPERVISED INPUT 0 txog 11 tus pins ntes cov vol.tage ntws los ntawm lub voj voog los saib xyuas cov khoom siv tsis sib xws, luv luv, rau, thiab tawm, thiab tseem tuaj yeem siv tau raws li TTL cov tswv yim dav dav. Nrog BioStar 2, koj tuaj yeem teeb tsa tus cwj pwm raws li Tus Saib Xyuas Cov Lus Qhia, thiab koj tuaj yeem saib xyuas cov xwm txheej ntawm txhua qhov kev tawm tswv yim.
Nco tseg:
- Tsis txhob txuas cov tswv yim ntawm Input Module nyob rau hauv duplicate rau lub cuab yeej txuas nrog lub tswv yim chaw nres nkoj ntawm tus tswv ntaus ntawv.
- Lub Input Module tuaj yeem siv los ntawm kev sib txuas 1 kΩ, 2.2 kΩ, 4.7 kΩ, lossis 10 kΩ resistors. Tom qab txuas cov resistor sib raug rau cov khoom siv nkag ntawm kev sib txuas, teeb tsa tib tus nqi tiv thaiv hauv BioStar 2.
- Txhawm rau kawm paub yuav ua li cas khiav lag luam nyob ntawm qhov kev saib xyuas cov tswv yim, xa mus rau phau ntawv ntawm BioStar 2.
Tampyog Connection
Yog tias Input Module raug tshem tawm los ntawm qhov chaw teeb tsa vim muaj qhov cuam tshuam sab nraud, nws tuaj yeem ua rau lub tswb lossis txuag qhov xwm txheej.
Siv lub Input Module nrog lub enclosure
Lub Input Module tuaj yeem ntsia tau rau hauv lub thawv (ENCR-10) rau kev tiv thaiv lub cev thiab hluav taws xob. Lub kaw lus muaj xws li lub hwj chim xwm txheej LED board, lub hwj chim faib board, fais fab mov, thiab tampua. Lub kaw lus yog muag nyias.
Kev ruaj ntseg lub roj teeb
Ntxig lub roj teeb velcro pluaj rau hauv lub thawv thiab tuav lub roj teeb.
Nco tseg: Siv lub roj teeb thaub qab nrog 12 VDC thiab 7 Ah lossis siab dua. Cov khoom no tau sim nrog 'ES7-12' roj teeb ntawm 'ROCKET'. Nws raug nquahu kom siv lub roj teeb sib raug rau 'ES7-12'.
- Lub roj teeb muag nyias.
- Yog tias qhov loj me ntawm lub roj teeb thaub qab loj dua li qhov kev qhia tshwj xeeb, nws yuav tsis tuaj yeem muab tso rau hauv lub thawv lossis lub thawv yuav tsis kaw tom qab nws tau teeb tsa. Tsis tas li ntawd, yog tias cov duab thiab qhov ntev ntawm cov terminals txawv, lub roj teeb tsis tuaj yeem txuas nrog siv lub cable muab.
Txhim kho lub Input Module nyob rau hauv lub enclosure
- Txheeb xyuas txoj haujlwm txhawm rau txhim kho Cov Khoom Siv Hluav Taws Xob hauv lub thawv. Koj tuaj yeem nruab ob Input Modules hauv ib lub thawv.
- Tom qab tso lub Input Module nyob rau hauv lub enclosure, kho nws nrog lub fixing screws.
- Tsis muaj qhov siab zoo rau kev txhim kho ENCR-10 ntawm phab ntsa. Nruab nws rau qhov chaw nyab xeeb thiab yooj yim rau koj siv.
- Txhim kho cov ntsia hlau rau lub qhov rooj, cov cuab yeej thiab cov khoom siv hluav taws xob muaj nyob rau hauv pob ENCR-10. Siv txhua tus ntsia hlau kom raug raws li cov ntsiab lus hauv qab no.
- Kho cov ntsia hlau rau lub qhov rooj (inch: 4 mm, ntev: 25 mm) x 4
- Txhim kho cov ntsia hlau rau lub cuab yeej (inch: 3 hli, ntev: 5 hli) x 6
- Txhim kho screws rau lub hwj huam mov cable (inch: 3 hli, ntev: 8 hli) x 1
Fais fab thiab AUX Input Connection
Koj tuaj yeem txuas qhov Uninterruptible Power Supply (UPS) los tiv thaiv lub zog tsis ua haujlwm. Thiab lub hwj chim tsis ua hauj lwm ntes los yog cov khoom tawm qhuav tuaj yeem txuas nrog AUX hauv davhlau ya nyob twg.
- Nco ntsoov siv lub zog sib cais rau cov cuab yeej tswj kev nkag mus thiab cov tswv yim Module.
- Siv cov khoom siv hluav taws xob kom raug (12 VDC, 130 mA lossis 24 VDC, 82 mA).
Tampyog Connection
Yog tias Input Module raug tshem tawm los ntawm qhov chaw teeb tsa vim muaj qhov cuam tshuam sab nraud, nws tuaj yeem ua rau lub tswb lossis txuag qhov xwm txheej.
- Yog xav paub ntxiv, hu rau Suprema technical support team (support.supremainc.com).
Nta
| Qeb | Feature | Specification |
|
General |
Qauv | IB-120 |
| CPU | Cortex M3 72 MHz | |
| Nco | 512 KB Flash + 64 KB SRAM | |
|
LED |
• Ntau xim
• Lub zog – 1 • xwm txheej – 1 • RS-485 TX – 1 • RS-485 RX – 1 • Saib xyuas cov tswv yim – 12 • Relay – 2 • AUX IN – 2 • Tampua- 1 |
|
| Ua haujlwm kub | -20 ° C - 60 ° C | |
| Cia Kub | -40 ° C - 70 ° C | |
| Kev khiav dej num | 0% -95%, tsis-condensing | |
| Cia Humidity | 0% -95%, tsis-condensing | |
| Qhov Loj (W x H x D) | 90 mm x 190 mm x 21 mm | |
| Qhov hnyav | 203 g ib | |
| Daim ntawv pov thawj | CE, FCC, KC, RoHS, REACH, WEEE | |
|
Interface |
Saib xyuas cov khoom siv | 12 ch (TTL tswv yim xaiv tau) |
| RS-485 | 1 ch ib | |
| Relay | 2 relay cov | |
| AUX cov tswv yim | 2 ch (AC fais fab tuag) | |
| Tampyog Input | 1 ch ib | |
| Muaj peev xwm | Text Log | 10ea per port * |
|
Hluav taws xob |
Hwj chim |
• Hwj chim: DC 12 V (Max. 130 mA) los yog DC 24 V (Max. 82 mA)
• Adapter pom zoo specifications: DC 12 V (± 10%) nrog tsawg kawg yog 1 A lossis DC 24 V (± 10%) nrog qhov tsawg kawg nkaus ntawm 1 A ** |
| Hloov Input VIH | Max. 5V (Kev sib cuag qhuav) | |
| Relay | 5 A @ 30 VDC Resistive load |
- Cov khoom tshwj xeeb yuav raug hloov pauv yam tsis tau ceeb toom txog kev txhim kho.
- Rau cov xwm txheej uas tshwm sim thaum lub network kev twb kev txuas ploj lawm, mus txog 10 txheej xwm tuaj yeem khaws cia rau ib qhov chaw nres nkoj. Thaum lub chaw nres nkoj puv, txhua qhov kev tshwm sim tshiab uas tau teev tseg yuav hloov qhov qub tshaj plaws.
- Lub adapter yog muag nyias. Xa mus rau cov lus qhia tshwj xeeb.
Qhov ntev
Cov ntaub ntawv ua raws li FCC
Cov cuab yeej no ua raws li Tshooj 15 ntawm FCC txoj cai.
Kev ua haujlwm yog ua raws li ob yam hauv qab no:
- Cov cuab yeej no yuav tsis ua teeb meem cuam tshuam, thiab
- Cov cuab yeej no yuav tsum lees txais ib qho kev cuam tshuam tau txais, suav nrog kev cuam tshuam uas yuav ua rau kev ua haujlwm tsis xav tau.
- Cov cuab yeej no tau raug sim thiab pom tias ua raws li cov kev txwv rau Class A cov cuab yeej digital, ua raws li Tshooj 15 ntawm FCC Cov Cai. Cov kev txwv no yog tsim los muab kev tiv thaiv tsim nyog tiv thaiv kev cuam tshuam hauv kev lag luam. Cov cuab yeej no tsim, siv, thiab tuaj yeem tawg lub zog ntawm xov tooj cua thiab, yog tias tsis tau nruab thiab siv raws li phau ntawv qhia, nws yuav ua rau muaj kev cuam tshuam rau kev sib txuas lus hauv xov tooj cua. Kev ua haujlwm ntawm cov khoom siv no hauv thaj chaw nyob yuav ua rau muaj kev cuam tshuam tsis zoo, yog li tus neeg siv yuav tsum tau kho qhov cuam tshuam ntawm nws tus kheej.
- Kev hloov kho: Txhua qhov kev hloov kho rau lub cuab yeej no uas tsis tau pom zoo los ntawm Suprema Inc. tuaj yeem ua rau tsis muaj txoj cai tso cai rau tus neeg siv los ntawm FCC los khiav cov cuab yeej no.
Cov ntawv txuas ntxiv
Tsis lees paub
- Cov ntaub ntawv nyob rau hauv daim ntawv no yog muab nrog rau cov khoom Suprema.
- Txoj cai siv tau lees paub tsuas yog rau Suprema cov khoom lag luam suav nrog hauv cov nqe lus thiab kev siv lossis kev muag khoom rau cov khoom lag luam uas tau lees paub los ntawm Suprema. Tsis muaj daim ntawv tso cai, qhia los yog hais, los ntawm estoppel los yog lwm yam, rau ib qho kev txawj ntse yog tso cai los ntawm daim ntawv no.
- Tsuas yog raws li tau hais tseg hauv kev pom zoo ntawm koj thiab Suprema, Suprema xav tias tsis muaj kev lav phib xaub, thiab Suprema tsis lees paub txhua qhov kev lees paub, qhia lossis qhia suav nrog, tsis muaj kev txwv, cuam tshuam txog kev noj qab haus huv rau ib lub hom phiaj, kev ua lag luam, lossis tsis ua txhaum cai.
- Txhua qhov kev lees paub yog VOID yog tias cov khoom lag luam Suprema tau ua tiav: 1) teeb tsa tsis raug lossis qhov twg cov lej cim, hnub lav lossis daim ntawv pov thawj zoo ntawm cov khoom siv tau hloov kho lossis tshem tawm; 2) siv nyob rau hauv ib yam uas tsis yog raws li kev tso cai los ntawm Suprema; 3) hloov kho, hloov kho, lossis kho los ntawm ib tog twg uas tsis yog Suprema lossis ib tog tau tso cai los ntawm Suprema; los yog 4) ua haujlwm lossis khaws cia hauv ib puag ncig tsis zoo.
- Cov khoom lag luam Suprema tsis yog tsim los siv rau hauv kev kho mob, kev cawm neeg txoj sia, kev siv lub neej, lossis lwm yam kev siv uas tsis ua haujlwm ntawm cov khoom Suprema tuaj yeem tsim qhov xwm txheej uas tus kheej raug mob lossis tuag taus. Yog tias koj yuav lossis siv Suprema cov khoom lag luam rau ib daim ntawv thov uas tsis xav tau lossis tsis tau tso cai, koj yuav tsum them nyiaj thiab tuav Suprema thiab nws cov tub ceev xwm, cov neeg ua haujlwm, cov koom tes, cov koom tes, thiab cov neeg faib khoom tsis raug rau txhua qhov kev thov, nqi, kev puas tsuaj, thiab cov nuj nqis, thiab cov nqi kws lij choj tsim nyog tshwm sim. tawm ntawm, ncaj qha lossis tsis ncaj, ib qho kev thov ntawm tus kheej raug mob lossis tuag cuam tshuam nrog kev siv yam tsis xav tau lossis tsis raug tso cai, txawm tias qhov kev thov no tau liam tias Suprema tsis saib xyuas txog kev tsim lossis tsim khoom.
- Suprema muaj txoj cai los hloov cov lus qhia tshwj xeeb thiab cov lus piav qhia ntawm cov khoom txhua lub sijhawm yam tsis muaj ntawv ceeb toom los txhim kho kev ntseeg siab, ua haujlwm, lossis tsim qauv.
- Cov ntaub ntawv tus kheej, nyob rau hauv daim ntawv ntawm kev lees paub cov lus thiab lwm cov ntaub ntawv txheeb ze, tuaj yeem khaws cia hauv Suprema cov khoom thaum siv. Suprema tsis muaj lub luag haujlwm rau txhua yam ntaub ntawv, suav nrog cov ntaub ntawv ntiag tug, khaws cia hauv Suprema cov khoom lag luam uas tsis nyob hauv Suprema txoj kev tswj hwm ncaj qha lossis raws li tau hais los ntawm cov ntsiab lus thiab cov xwm txheej. Thaum twg cov ntaub ntawv khaws cia, suav nrog cov ntaub ntawv tus kheej, siv, nws yog lub luag haujlwm ntawm cov neeg siv khoom kom ua raws li kev cai lij choj hauv tebchaws (xws li GDPR) thiab xyuas kom muaj kev tuav thiab ua tiav.
- Koj yuav tsum tsis txhob cia siab rau qhov tsis muaj lossis cov yam ntxwv ntawm cov yam ntxwv lossis cov lus qhia uas cim "tso tseg" lossis
"tsis tau txhais." Suprema khaws cov no rau yav tom ntej txhais thiab yuav tsum tsis muaj lub luag haujlwm rau kev tsis sib haum xeeb lossis kev tsis sib haum xeeb uas tshwm sim los ntawm kev hloov pauv yav tom ntej rau lawv. - Tsuas yog raws li tau hais tseg hauv no, rau qhov siab tshaj plaws tau tso cai los ntawm txoj cai, cov khoom lag luam Suprema raug muag "raws li yog".
- Hu rau koj lub chaw muag khoom Suprema hauv zos lossis koj tus neeg xa khoom kom tau txais cov lus qhia tseeb thiab ua ntej muab koj cov khoom xaj.
Daim Ntawv Ceeb Toom Copyright
Suprema muaj cov cai ntawm daim ntawv no. Cov cai ntawm lwm cov khoom npe, hom, thiab cov cim lag luam yog rau cov tib neeg lossis cov koom haum uas muaj lawv..
Open Source License
- Txhawm rau thov cov cai hloov kho raws li FreeRTOS, uas suav nrog hauv cov khoom no, thov mus saib ntawm support.supremainc.com thiab hu rau Suprema Tech Team.
MIT Open Source License
Kev tso cai no tau tso cai, pub dawb, rau txhua tus neeg tau txais daim ntawv theej ntawm cov software no thiab cov ntaub ntawv cuam tshuam files ("Software"), los cuam tshuam hauv Software yam tsis muaj kev txwv, suav nrog tsis txwv txoj cai siv, luam tawm, hloov kho, sib koom ua ke, tshaj tawm, faib, sublicense, thiab / lossis muag cov ntawv theej ntawm Software, thiab tso cai rau tib neeg mus leej twg lub Software tau muab los ua li ntawd, raws li cov hauv qab no:
Daim ntawv ceeb toom kev cai lij choj saum toj no thiab daim ntawv ceeb toom kev tso cai no yuav tsum muab tso rau hauv txhua daim ntawv luam lossis feem ntau ntawm Software.
LUB SOFTWARE tau muab "raws li yog", yam tsis muaj kev lav phib xaub ntawm txhua yam, nthuav tawm lossis qhia, suav nrog tab sis tsis txwv rau kev lav phib xaub ntawm kev muag khoom, FITNESS rau lub hom phiaj tshwj xeeb. YUAV TSUM TAU TXAIS LUB SIJ HAWM LOS NTAWM COV TSEV KAWM NTAWV lossis cov neeg tuav cai lij choj yuav tsum lav rau txhua qhov kev thov, kev puas tsuaj lossis lwm yam kev lav phib xaub, txawm tias nyob rau hauv kev ua txhaum ntawm kev cog lus, kev tsim txom lossis lwm yam, tshwm sim los ntawm, tawm ntawm lossis cuam tshuam rau hauv kev lag luam. Lwm yam kev lag luam hauv SOFTWARE.
© 2022 Suprema Inc. Suprema thiab txheeb xyuas cov npe khoom thiab cov lej ntawm no yog cov cim kev lag luam sau npe ntawm Suprema, Inc. Txhua lub npe tsis yog Suprema thiab cov npe khoom yog cov cim lag luam lossis cov cim lag luam ntawm lawv cov tuam txhab.
Cov khoom zoo li, tsim raws li txoj cai thiab/los yog specifications yuav hloov tsis tau ceeb toom.
Cov ntaub ntawv / Cov ntaub ntawv
 |
suprema IM-120 Multiple Entry Input Module [ua pdf] Daim ntawv qhia kev teeb tsa EN 101.00.IM-120 V1.02A, IM-120 Ntau Qhov Kev Nkag Nkag Nkag Module, IM-120, Ntau Qhov Nkag Nkag Nkag Module, Nkag Nkag Nkag Module, Nkag Nkag Nkag, Module |
