Quantek KPN Access Control Keypad thiab Nyeem Ntawv
Thov nyeem phau ntawv ua tib zoo ua ntej txhim kho chav tsev no
Cov ntawv ntim khoom
| Lub npe | Ntau | Lus hais |
| Keypad | 1 | |
| Cov neeg siv phau ntawv | 1 | |
| Screwdriver | 1 | |
| Phab ntsa ntsaws | 2 | Siv rau kho |
| Self-tapping screws | 2 | Φ4mm × 25mm, siv los kho |
| Master cards | 2 | Ntxiv & rho tawm |
| Tom ntej: Diode IN4004 | 1 | Rau relay tiv thaiv Circuit Court |
Thov xyuas kom meej tias tag nrho cov ntsiab lus saum toj no raug. Yog tias muaj dab tsi ploj, thov ceeb toom rau peb tam sim.
Kev piav qhia
KPN yog ib lub qhov rooj multifunction standalone access controller lossis Wiegand output keypad/card reader. Nws yog tsim rau mounting nyob rau hauv tsev los yog sab nraum zoov nyob rau hauv hnyav ib puag ncig. Nws yog nyob rau hauv lub zog, ruaj khov, thiab vandal-proof zinc alloy hmoov coated rooj plaub. Nws siv Atmel MCU kom ruaj khov ua haujlwm. Kev ua haujlwm yog tus neeg siv tau zoo heev, thiab lub zog hluav taws xob qis ua kom lub neej ua haujlwm ntev. Chav tsev no txhawb nqa txog li 1000 tus neeg siv (998 cov neeg siv ntau thiab 2 cov neeg siv ntshai), txhua tus neeg siv cov ntaub ntawv tuaj yeem hloov pauv ntawm ib qho mus rau lwm qhov uas muaj txiaj ntsig zoo yog tias muaj ntau KPNs ntawm tib lub xaib, tsuas yog 1 yuav tsum tau programmed txuag lub sijhawm. . Lub inbuilt card nyeem ntawv txhawb 125KHZ EM phaib. Chav tsev muaj ntau yam ntxiv xws li Wiegand tso zis, interlock hom, thiab cov yuam sij backlit. Cov yam ntxwv no ua rau chav tsev yog qhov kev xaiv zoo tshaj plaws rau kev nkag mus rau qhov rooj tsis yog rau cov khw me thiab cov tsev neeg hauv tsev xwb tab sis kuj tseem siv rau kev lag luam thiab kev lag luam xws li factories, warehouses, laboratories, etc.
Nta
- Txhawb nqa dav voltage input 12-28Vac/dc
- Waterproof, ua raws li IP66
- Muaj zog zinc alloy hmoov-coated anti-vandal rooj plaub
- Tag nrho cov kev pab cuam los ntawm daim ntawv
- 1000 cov neeg siv, daim npav txhawb nqa, PIN, lossis daim npav + PIN
- PIN ntev 4-6 tus lej
- Cov yuam sij backlit
- Wiegand 26-37 ntsis input & output
- Tri-xim LED xwm txheej zaub
- Integrated tswb thiab buzzer tso zis
- Pulse los yog toggle hom
- Cov neeg siv cov ntaub ntawv yuav raug xa mus
- 2 cov khoom siv tuaj yeem cuam tshuam rau 2 qhov rooj
- Ua-nyob rau hauv lub teeb-dependent resistor (LDR) rau anti-tamper
Specification
| Kev khiav hauj lwm voltage
Idle tam sim no noj Max tam sim no noj |
12-28VAC / dc
<35mA <80mA |
| Cov neeg siv muaj peev xwm
Cov neeg siv nquag Panic cov neeg siv |
1000
998 |
| Sib thooj daim npav nyeem ntawv
Ntau zaus Daim npav nyeem nyob deb |
EM
125 KHz 2-6 cm |
| Cov kab txuas txuas | Relay tso zis, tawm khawm, tswb, qhov rooj tiv tauj, Wiegand input, Wiegand tso zis |
| Relay
Adjustable relay lub sij hawm Relay siab tshaj load |
Ib (Common, NO, NC)
1-99 vib nas this (5 vib nas this default), lossis Toggle hom 2Amp |
| Wiegand interface
Wiegand tswv yim Wiegand tso zis PIN tso zis |
Wiegand 26-37 ntsis (Default: Wiegand 26 ntsis, 4bits)
26-37 ib 26-37 ib 4 ntsis, 8 ntsis (ASCII), 10 tus lej virtual |
| Ib puag ncig
Kev khiav hauj lwm kub Ua hauj lwm humidity |
Raws li IP66
-45 rau 60 ⁰C 0% RH rau 98% RH |
| Lub cev
Xim Dimensions Chav ntsuas qhov hnyav |
Zinc alloy
Nyiaj 134 x 55.5 x 21 hli 340g |
Kev teeb tsa
- Tshem lub hau rov qab los ntawm lub keypad siv cov khoom siv tshwj xeeb ntsia hlau.
- Kos thiab laum ob lub qhov ntawm phab ntsa rau tus kheej-tapping kho screws thiab ib qho rau cable.
- Muab ob phab ntsa ntsaws rau hauv qhov kho qhov.
- Txhim kho lub nraub qaum kom ruaj khov ntawm phab ntsa nrog ob tus kheej tapping screws.
- Xov lub cable los ntawm lub qhov cable.
- Muab lub pob nyem tso rau sab hau tom qab.
Kev xaim
| Xim | Muaj nuj nqi | Kev piav qhia |
| Basic standalone thaiv | ||
| Liab | AC / DC | 12-28Vac / dc tswj fais fab input |
| Dub | AC / DC | 12-28Vac / dc tswj fais fab input |
| Paj yeeb | GND | Hauv av |
| Xiav | TSIS MUAJ | Lub relay nquag qhib qhov tso zis |
| Ntshav | COM | Relay tso zis ntau |
| Txiv kab ntxwv | NC | Relay nquag kaw cov zis |
| Daj | Qhib | Tawm khawm tawm tswv yim (Nquag qhib, txuas lwm qhov kawg rau GND) |
| Kev xaim xaim (Wiegand nyeem lossis tus tswj hwm) | ||
| Ntsuab | D0 | Wiegand input/output Cov ntaub ntawv 0 |
| Dawb | D1 | Wiegand input/output Cov ntaub ntawv 1 |
| Advanced input thiab output nta | ||
| Grey | Tswb | Sab nraud tswb tso zis tsis zoo |
| Xim av | D_IN
LUB SIJ HAWM |
Qhov rooj / rooj vag sib nqus sib nqus input (Nquag kaw, txuas
Lwm qhov kawg rau GND) |
- Nco tseg: Yog tias lub pob tawm tsis tau txuas nrog, nws raug nquahu kom tseem khiav cov xaim daj rov qab mus rau lub zog hluav taws xob thiab cia nws kaw los yog ntawm lub davhlau ya nyob twg thaiv.
- Qhov no yuav ua rau nws yooj yim dua los ua lub Hoobkas rov pib dua tom qab yog tias xav tau, zam qhov yuav tsum tau tshem cov keypad ntawm phab ntsa.
- Saib nplooj ntawv kawg kom paub ntau ntxiv txog yuav ua li cas rov pib lub Hoobkas.
- Kaw tag nrho cov xov hlau tsis siv los tiv thaiv luv luv.
Suab & lub teeb qhia
| Kev ua haujlwm | LED qhov taw qhia | Buzzer |
| Standby | Liab | |
| Nkag mus rau programming hom | Liab flashing maj mam | Ib beep |
| Nyob rau hauv lub programming zaub mov | Daj | Ib beep |
| Kev ua haujlwm yuam kev | Peb lub suab nrov | |
| Tawm hauv qhov programming hom | Liab | Ib beep |
| Qhov rooj xauv | Ntsuab | Ib beep |
| Tswb | Liab flashing sai | Tswb |
Yooj yim ceev programming phau ntawv qhia
| Nkag mus rau programming hom | * 123456 #
Tam sim no koj tuaj yeem ua qhov programming. 123456 yog tus thawj tswj hwm code. |
| Hloov tus lej lej | 0 Tshiab Master code # Tshiab Master code #
Tus lej lej yog 6 tus lej |
| Ntxiv cov neeg siv daim npav | 1 Nyeem daim npav #
Daim npav tuaj yeem muab ntxiv txuas ntxiv yam tsis tau tawm ntawm lub programming hom |
| Ntxiv tus neeg siv PIN | 1 PIN #
PINs tuaj yeem muab ntxiv txuas ntxiv yam tsis tau tawm ntawm lub programming hom. Tus PIN yog tus lej 4-6 tus lej, tshwj tsis yog 8888 uas tau tshwj tseg. |
| Rho tawm neeg siv | 2 Nyeem daim npav # rau tus neeg siv daim npav
2 Nkag mus PIN # rau tus neeg siv PIN |
| Tawm hauv qhov programming hom | * |
| Yuav tso lub qhov rooj li cas | |
| Tus neeg siv daim npav | Nyeem daim npav |
| Tus neeg siv tus PIN | Nkag mus PIN # |
Standalone hom
- KPN tuaj yeem siv los ua tus nyeem ntawv ib leeg rau ib lub qhov rooj lossis rooj vag
- Master code #7 2 # (Factory default mode)
Kab kos duab - Xauv
Daim duab kab xev - rooj vag, barrier, thiab lwm yam. 
Teem ib tug tshiab master code
| 1. Nkag mus rau hom programming | * Master code #
123456 yog tus thawj tswj hwm code |
| 2. Hloov tus lej lej | 0 Tshiab Master code # Tshiab Master code #
Tus lej lej yog 6 tus lej |
| 3. Tawm hauv qhov programming hom | * |
Nws raug nquahu kom khaws cov ntaub ntawv ntawm Tus Neeg Siv Khoom ID thiab tus lej daim npav kom tso cai rau tus kheej tshem tawm daim npav thiab tus lej PIN yav tom ntej, saib nplooj ntawv kawg.
Ntxiv cov neeg siv ntau - daim npav
| 1. Nkag mus rau hom programming | * Master code #
123456 yog tus thawj tswj hwm code |
| 2. Ntxiv ib tus neeg siv daim npav (txoj kev 1)
KPS yuav cia li muab daim npav rau tus neeg siv tus lej ID tom ntej |
1 Nyeem daim npav #
Daim npav tuaj yeem muab ntxiv txuas ntxiv yam tsis tau tawm ntawm lub programming hom |
| 2. Ntxiv ib tus neeg siv daim npav (txoj kev 2)
Nyob rau hauv txoj kev no, tus neeg siv tus lej ID raug faib rau ib daim npav. Tus neeg siv tus lej ID yog ib tus lej los ntawm 0-997 : kuv. Tsuas yog ib tus neeg siv tus lej ID rau ib daim npav. |
1 Tus neeg siv tus lej ID # Nyeem daim npav #
Daim npav tuaj yeem muab ntxiv txuas ntxiv yam tsis tau tawm ntawm lub programming hom |
| 2. Ntxiv ib tus neeg siv daim npav (txoj kev 3)
Nyob rau hauv txoj kev no, daim npav yog ntxiv los ntawm 8 lossis 10-tus lej daim npav tus lej luam tawm ntawm daim npav. Tus neeg siv tus lej ID raug muab tso tseg. |
1 Daim npav naj npawb #
Daim npav tuaj yeem muab ntxiv txuas ntxiv yam tsis tau tawm ntawm lub programming hom |
| 2. Ntxiv ib qhov thaiv ntawm daim npav ua ntu zus
Tso cai rau tus neeg saib xyuas ntxiv txog 998 daim npav nrog cov lej sib txuas rau tus nyeem ntawv hauv ib kauj ruam. Yuav siv sijhawm li 2 feeb rau qhov program. |
1 Tus neeg siv tus lej ID # Daim npav kom muaj nuj nqis # Thawj daim npav naj npawb # |
| 3. Tawm hauv qhov programming hom | * |
Ntxiv cov neeg siv ntau - PIN
| 1. Nkag mus rau hom programming | * Master code #
123456 yog tus thawj tswj hwm code |
| 2. Ntxiv tus PIN (Txoj Kev 1)
KPS yuav cia li muab tus PIN rau tus neeg siv tus lej ID tom ntej |
1 PIN #
PINs tuaj yeem muab ntxiv txuas ntxiv yam tsis tau tawm ntawm lub programming hom. Tus PIN yog tus lej 4-6 tus lej, tshwj tsis yog 8888 uas tau tshwj tseg. |
| 2. Ntxiv tus PIN (Txoj Kev 2)
Hauv txoj kev no, tus neeg siv tus lej ID raug faib rau tus lej PIN. Tus neeg siv tus lej ID yog ib tus lej los ntawm 0-997 : kuv. Tsuas yog ib tus neeg siv tus lej ID rau ib tus PIN. |
1 Tus neeg siv tus lej ID # PIN #
PINs tuaj yeem muab ntxiv txuas ntxiv yam tsis tau tawm ntawm lub programming hom. Tus PIN yog tus lej 4-6 tus lej, tshwj tsis yog rau 8888 uas tau tshwj tseg. |
| 3. Tawm hauv qhov programming hom | * |
Ntxiv cov neeg siv ceeb
Thaum tus PIN txaus ntshai nkag los lossis nyeem daim npav ceeb, lub tsev tseem yuav tso cai nkag mus tau ib txwm, tab sis lub tswb sab nraud yuav qhib. Chav tsev yuav tsum tau depowered kom tua lub tswb ceeb ntshai.
| 1. Nkag mus rau hom programming | * Master code #
123456 yog tus thawj tswj hwm code |
| 2. Ntxiv ib daim npav LOSSIS
Ntxiv tus PIN |
1 Tus neeg siv tus lej ID # Nyeem daim npav LOSSIS 8/10 tus lej daim npav #
1 Tus neeg siv tus lej ID # PIN # Tus neeg siv tus lej ID yog 998 lossis 999 |
| 3. Tawm hauv qhov programming hom | * |
Muab tus PIN rau tus neeg siv daim npav
Ua ntej, ntxiv ib daim npav raws li nplooj ntawv dhau los
| Nco ntsoov qhov no ua tiav sab nraud ntawm hom programming, cov neeg siv tuaj yeem ua qhov no lawv tus kheej | |
| 1. Muab tus PIN rau tus neeg siv daim npav | * Nyeem daim npav 8888 # PIN tshiab # Rov ua dua tus PIN tshiab # |
| 2. Tawm | * |
Hloov cov neeg siv PIN
| Nco tseg: qhov no yog ua tiav sab nraum lub programming hom, cov neeg siv tuaj yeem ua qhov no lawv tus kheej | |
| 1. Hloov PIN los ntawm daim npav | * Nyeem daim npav PIN qub # PIN tshiab # Rov ua dua tus PIN tshiab # |
| 2. Hloov tus PIN los ntawm tus neeg siv ID | * Tus neeg siv ID # PIN qub # PIN tshiab # Rov ua dua tus PIN tshiab # |
| 3. Tawm | * |
Rho tawm cov neeg siv ntau - daim npav
| 1. Nkag mus rau hom programming | * Master code #
123456 yog tus thawj tswj hwm code |
| 2. Rho tawm tus neeg siv daim npav (txoj kev 1)
Rho tawm tus neeg siv los ntawm kev nyeem lawv daim npav |
2 Nyeem daim npav #
Daim npav tuaj yeem raug tshem tawm tsis tu ncua yam tsis tau tawm ntawm kev ua haujlwm hom |
| 2. Rho tawm tus neeg siv daim npav (txoj kev 2)
Rho tawm tus neeg siv los ntawm tus neeg siv tus lej ID. Txoj kev no yuav pab tau yog tias tus neeg siv tau poob lawv daim npav |
2 Tus neeg siv tus lej ID #
Daim npav tuaj yeem raug tshem tawm tsis tu ncua yam tsis tau tawm ntawm kev ua haujlwm hom |
| 2. Rho tawm tus neeg siv daim npav (txoj kev 3)
Rho tawm tus neeg siv los ntawm 8/10 tus lej daim npav. Txoj kev no yuav pab tau yog tias tus neeg siv tau poob lawv daim npav |
2 Input card naj npawb #
Daim npav tuaj yeem raug tshem tawm tsis tu ncua yam tsis tau tawm ntawm kev ua haujlwm hom |
| 3. Tawm hauv qhov programming hom | * |
Rho tawm cov neeg siv ntau - PIN
| 1. Nkag mus rau hom programming | * Master code #
123456 yog tus thawj tswj hwm code |
| 2. Rho tawm tus PIN (Txoj Kev 1)
Rho tawm tus neeg siv los ntawm kev nkag mus rau lawv tus PIN |
2 Tus lej PIN #
PINs tuaj yeem raug tshem tawm tsis tu ncua yam tsis tau tawm ntawm lub programming hom |
| 2. Rho tawm tus PIN (Txoj Kev 2)
Rho tawm tus neeg siv los ntawm tus neeg siv tus lej ID |
2 Tus neeg siv tus lej ID #
PINs tuaj yeem raug tshem tawm tsis tu ncua yam tsis tau tawm ntawm lub programming hom |
| 3. Tawm hauv qhov programming hom | * |
Rho tawm cov neeg siv ceeb
| 1. Nkag mus rau hom programming | * Master code #
123456 yog tus thawj tswj hwm code |
| 2. Rho tawm tus neeg siv ceeb
Rho tawm tus neeg siv los ntawm kev nkag mus rau lawv tus PIN |
2 Tus neeg siv tus lej ID #
Tus neeg siv tus lej ID yog 998 lossis 999. Txoj kev yog tib yam rau daim npav thiab tus lej PIN |
| 3. Tawm hauv qhov programming hom | * |
Rho tawm TXHUA cov neeg siv
| 1. Nkag mus rau hom programming | * Master code #
123456 yog tus thawj tswj hwm code |
| 2. Rho tawm tag nrho cov neeg siv | 2 Master code # |
| 3. Tawm hauv qhov programming hom | * |
Teem relay configuration
| 1. Nkag mus rau hom programming | * Master code #
123456 yog tus thawj tswj hwm code |
| 2. Pulse hom
OR 2. Latch hom |
3 1-99 #
Lub sij hawm relay yog 1-99 vib nas this. (1 sib npaug 50mS). Lub neej ntawd yog 5 vib nas this. 3 # Nyeem ntawv siv tau, relay keyboards. Nyeem daim npav siv tau dua, relay switches rov qab. |
| 3. Tawm hauv qhov programming hom | * |
Teeb hom kev nkag
| 1. Nkag mus rau hom programming | * Master code #
123456 yog tus thawj tswj hwm code |
| 2. Daim npav nkaus xwb
OR 2. Daim npav + PIN OR 2. Daim npav lossis PIN OR 2. Ntau daim npav / PINs nkag |
4 #
4 #
4 # (default)
4 3 (2-9) # Tsuas yog tom qab nyeem 2-9 daim npav lossis nkag 2-9 PINs tuaj yeem qhib qhov rooj. Lub sij hawm luv luv ntawm kev nyeem ntawv / tso PINs tsis tuaj yeem tshaj 5 vib nas this lossis lub tsev yuav tawm mus rau qhov chaw tos txais. |
| 3. Tawm hauv qhov programming hom | * |
Teem lub tswb nrov tawm tsam
Lub tswb nrov tawm tsam yuav koom nrog tom qab 10 daim npav ua tsis tiav. Factory default yog OFF. Nws tuaj yeem raug teeb tsa kom tsis kam nkag rau 10 feeb lossis qhib tus nyeem ntawv lub tswb.
| 1. Nkag mus rau hom programming | * Master code #
123456 yog tus thawj tswj hwm code |
| 2. Kev tawm tsam tawm
OR 2. Kev tawm tsam ON OR 2. Strike-out ON (Tswb) Teem lub sij hawm tswb |
6 #
Tsis muaj tswb los yog xauv tawm (default hom)
6 # Kev nkag yuav raug tsis kam lees rau 10 feeb
6 # Cov cuab yeej yuav ceeb toom rau lub sijhawm teev hauv qab no
5 0-3 # 0-3 yog lub sijhawm hauv feeb. Default yog 1 feeb. Sau tus lej lej # lossis daim npav siv tau / PIN kom ntsiag to |
| 3. Tawm hauv qhov programming hom | * |
Teem lub suab thiab pom cov lus teb
| 1. Nkag mus rau hom programming | * Master code #
123456 yog tus thawj tswj hwm code |
|
| 2. Tswj suab | OFF = 7 # | UA = 7 # (default) |
| 2. Tswj LED | OFF = 7 # | UA = 7 # (default) |
| 2. Tswj cov yuam sij backlit | OFF = 7 # | UA = 7 # (default) |
| 3. Tawm hauv qhov programming hom | * | |
Kev siv Master cards
| Siv daim npav master ntxiv thiab rho tawm daim npav cov neeg siv | |
| Ntxiv tus neeg siv | 1. Nyeem master add card
2. Nyeem daim npav neeg siv (Rov ua dua rau cov neeg siv daim npav ntxiv, tus neeg siv tus lej ID yuav raug xa mus rau qhov muaj nyob tom ntej) 3. Nyeem master ntxiv daim npav dua |
| Rho tawm tus neeg siv | 1. Nyeem daim npav rho tawm tus tswv
2. Nyeem daim npav neeg siv (Rov ua dua rau cov neeg siv daim npav ntxiv) 3. Nyeem daim npav rho tawm tus tswv dua |
Cov neeg siv kev ua haujlwm
Kom qhib lub qhov rooj:
- Nyeem daim npav uas siv tau lossis sau tus lej PIN siv tau.
- Yog tias nkag mus rau hom yog teem rau daim npav + PIN, nyeem daim npav ua ntej thiab nkag mus rau tus lej PIN hauv 5 vib nas this
Txhawm rau tua lub tswb:
- Nyeem daim npav siv tau lossis Sau tus lej PIN siv tau lossis sau tus lej lej #
- Chav tsev yuav tsum tau depowered kom tua lub tswb ceeb.
Xws li hom
- XK1 tuaj yeem ua haujlwm ua tus tswj hwm, txuas nrog tus nyeem ntawv Wiegand sab nraud.
- Master code # 7 2 # (Lub Hoobkas default hom)
Kab kos duab - Xauv
Daim duab kab xev - rooj vag, barrier, thiab lwm yam.
Teem Wiegand tawm tswv yim
Thov teeb lub Wiegand input hom raws li Wiegand tso zis hom ntawv ntawm tus nyeem ntawv sab nraud.
| 1. Nkag mus rau hom programming | * Master code #
123456 yog tus thawj tswj hwm code |
| 2. Wiegand input khoom | 8 26-37 : kuv # (Lub Hoobkas pib yog 26 ntsis) |
| 3. Tawm hauv qhov programming hom | * |
Yog tias KPN txuas nrog tus nyeem ntawv keyboard
Lub keyboard nyeem ntawv tuaj yeem yog 4 khoom, 8 khoom (ASCII), lossis 10 khoom hauv cov lej virtual tso zis. Xaiv cov haujlwm hauv qab no raws li tus lej PIN tso zis ntawm koj tus nyeem ntawv.
| 1. Nkag mus rau hom programming | * Master code #
123456 yog tus thawj tswj hwm code |
| 2. Wiegand input khoom | 8 4o8o 10 # (Lub Hoobkas pib yog 4 ntsis) |
| 3. Tawm hauv qhov programming hom | * |
Programming
- Basic programming yog tib yam li standalone hom.
- Nco tseg: Yog tias tus nyeem ntawv sab nraud yog EM (125KHz), ces daim npav tuaj yeem ntxiv rau ob chav. PINs tuaj yeem muab ntxiv rau ob chav.
Wiegand nyeem ntawv hom
KPN tuaj yeem ua haujlwm raws li tus qauv Wiegand nyeem ntawv, txuas nrog tus thib peb tus tswj hwm.
Txhawm rau teeb tsa hom no:
| 1. Nkag mus rau hom programming | * Master code #
123456 yog tus thawj tswj hwm code |
| 2. Wiegand nyeem ntawv hom | 7 3 # (Lub Hoobkas pib yog 26 ntsis) |
| 3. Tawm hauv qhov programming hom | * |
Kev xaim
- Thaum teeb tsa rau hom nyeem ntawv, cov xov hlau xim av thiab daj tau rov hais dua rau ntsuab LED tswj thiab buzzer tswj feem.
- Txhua qhov programming yog ua los ntawm tus neeg thib peb tus neeg saib xyuas nkag.
Teem Wiegand tawm tswv yim
Thov teeb lub Wiegand input hom raws li Wiegand tso zis hom ntawv ntawm tus nyeem ntawv sab nraud.
| 1. Nkag mus rau hom programming | * Master code #
123456 yog tus thawj tswj hwm code |
| 2. Wiegand input khoom | 8 26-37 : kuv # (Lub Hoobkas pib yog 26 ntsis) |
| 3. Tawm hauv qhov programming hom | * |
Advanced daim ntawv thov
Cov ntaub ntawv siv hloov pauv
- KPN txhawb cov neeg siv cov ntaub ntawv hloov chaw, tso cai rau cov neeg siv npe (daim npav thiab PINs) hloov mus rau lwm KPS lossis KPN chav tsev.
- Qhov no yog qhov muaj txiaj ntsig zoo thaum txhim kho ntau KPS / KPNs ntawm tib lub xaib thiab cov neeg siv muaj tib txoj cai nkag mus rau txhua lub qhov rooj, vim nws txhais tau tias tsuas yog ib chav tsev yuav tsum tau programmed thiab tag nrho cov ntaub ntawv tuaj yeem xa mus rau lwm chav nyob txuag sijhawm ntau. .
Cov kab kos duab:
Nco tseg:
- Master code yuav tsum yog tib yam ntawm ob chav.
- Programming yog ua los ntawm master unit nkaus xwb.
- Yog tias chav txais tau txais cov neeg siv tau sau npe lawm, nws yuav raug sau dua.
- Hloov mus yuav siv li 3 feeb.
| 1. Nkag mus rau hom programming | * Master code #
123456 yog tus thawj tswj hwm code |
| 2. Pib hloov pauv | 9 6 # |
| Tsis pub dhau 3 feeb, lub teeb ntsuab LED yuav teeb lub tsev yuav beep, LED yuav tig liab thiab cov neeg siv cov ntaub ntawv hloov mus ua tiav tiav. | |
| 3. Tawm | * |
Interlock
KPN txhawb nqa ob lub qhov rooj sib cuam tshuam. Ib tug keypad yog haum rau txhua lub qhov rooj. Tsuas yog thaum lub qhov rooj 2 kaw tag nrho, tus neeg siv tuaj yeem qhib lub keyboard 1, thiab rov ua dua.
Cov kab kos duab
Nruab IN4004 diodes hla lub xauv +V thiab -V
Nco tseg:
- Lub qhov rooj tiv thaiv yuav tsum tau muab ntsia thiab txuas nrog raws li daim duab qhia saum toj no.
- Sau npe rau cov neeg siv ntawm keypad 1, tom qab ntawd hloov cov neeg siv cov ntaub ntawv mus rau keypad 2 siv cov haujlwm tau piav qhia ntawm nplooj ntawv dhau los.
Teem ob lub keyboards rau kev sib cuam tshuam hom
| 1. Nkag mus rau hom programming | * Master code #
123456 yog tus thawj tswj hwm code |
| 2. Tig ON interlock | 9 1 # |
| 3. Tawm hauv qhov programming hom | * |
Txhawm rau tua lub interlock hom
| 1. Nkag mus rau hom programming | * Master code #
123456 yog tus thawj tswj hwm code |
| 2. TIV THAIV interlock | 9 0 # |
| 3. Tawm hauv qhov programming hom | * |
Hoobkas pib dua & ntxiv master cards
- Fais fab tuag, nias thiab tuav lub khawm tawm thaum lub zog ntawm lub tsev. Yuav muaj 2 beeps, tso lub khawm tawm, LED yuav tig daj. Tom qab ntawd nyeem ob daim npav EM 125KHz, thiab LED yuav tig liab.
- Thawj daim npav nyeem yog tus tswv ntxiv daim npav, daim npav thib ob nyeem yog daim npav rho tawm tus tswv. Lub Hoobkas pib dua tam sim no tiav.
- Cov ntaub ntawv siv tsis raug cuam tshuam.
Daim ntawv pov thawj
| Qhov chaw: | Qhov chaw qhov rooj: |
| Tus neeg siv ID No | Tus neeg siv lub npe | PIN | Daim npav naj npawb | Hnub tim |
| 0 | ||||
| 1 | ||||
| 2 | ||||
| 3 |
- Unit 11 Callywhite Business Park, Callywhite Lane, Dronfield, S18 2XP
- +44(0)1246 417113
- sales@cproxltd.com
- www.quantek.co.uk
Cov ntaub ntawv / Cov ntaub ntawv
 |
Quantek KPN Access Control Keypad thiab Nyeem Ntawv [ua pdf] Tus neeg siv phau ntawv KPN Access Control Keypad thiab nyeem ntawv, KPN, Kev tswj xyuas cov keypad thiab nyeem ntawv, Tswj keypad thiab nyeem ntawv, keypad thiab nyeem ntawv |
