MEAN-WELL PWM-120-12 Series Constant Voltage PWM Output LED Driver
AC tswv yim: 100-240Vac (rau DA2-Type nkaus xwb)
Tus neeg siv phau ntawv
Nta
- Qhov voltage PWM style output
- Daim ntawv thov teeb pom kev kub ntxhov yog muaj raws li IEC61347-2-13
- Built-in nquag PFC muaj nuj nqi thiab chav kawm II tsim
- No load power consumption <O.5W/ standby power consumption <O.5W(DA/DA2-type)
- Tag nrho encapsulated nrog IP67 qib
- Muaj nuj nqi xaiv: 3 hauv 1 dimming (dim-to-off); DALI/DAL-2
- Yam tsawg kawg dimming theem 0.2% rau DALI hom
- Hom lub neej> 50000 teev thiab 5 xyoo lav
Daim ntawv thov
- LED sawb teeb pom kev zoo
- Sab hauv LED teeb pom kev zoo
- LED teeb pom kev zoo
- LED architecture teeb pom kev zoo
- Muaj teeb pom kev zoo
- Ntaus "HL" siv rau hauv chav kawm l, faib 2 qhov chaw txaus ntshai (qhib) qhov chaw.
GTIN CODE
MW Nrhiav: https://www.meanwell.com/serviceGTlN.aspx
Kev piav qhia
PWM-120 series yog 120W AC / DC LED tsav tsheb featuring qhov tas li voltage mode with P WM style output, which is able to maintain the color temperature and the brightness homogeneity when driving all kinds of LED strips. PWM-120 operates from 90—305VAC and offers models with different rated voltage ranging between 12V and 48V. Thanks to the high efficiency up to 90.5%, with the fanless design, the entire series is able to operate for -40 C +90 C case temperature under free air convection. The entire series is rated with IP67 ingress protection level and is suitable to work for dry, damp los yog qhov chaw ntub dej. PWM-120 yog txawm peem rau nrog dimming muaj nuj nqi uas txawv lub luag hauj lwm voj voog ntawm cov zis, muab zoo yooj yooj yim rau LED strips daim ntaub ntawv.
Qauv Nkauj Kauj
SPECIFICATION
| Qauv | PWM-120-12 | PWM-120-24 | PWM-120-36 | PWM-120-48 | |
|
OUTPUT |
DC VOLTAGE | 12v XNUMX | 24v XNUMX | 36v XNUMX | 48v XNUMX |
| RATED CURRENT | 10 A | 5A | 3.4 A | 2.5 A | |
| RATED POWER | 120 W | 120 W | 122.4 W | 120 W | |
| DIMMING RANGE | 0 ~ 100% | ||||
| PWM FREQUENCY (Typ.) | 1.47kHz rau Blank/DA-Type, 2.5kHz rau DA2-Type | ||||
| SETUP, RISE SIJHAWM Nco tseg. 2
Nco tseg. 9 |
500ms, 80ms / 230VAC lossis 115VAC | ||||
| TAM SIM NO (Typ.) | 16ms/230VAC lossis 115VAC | ||||
|
NYIAJ |
VOLTAGE RANGE Nco tseg.3 | 90 ~ 305VAC 127 ~ 431VDC
(Thov xa mus rau ntu "TSHIAB CHARACTERISTIC") |
|||
| FREQUENCY RANGE | 47 ~ 63Hz | ||||
| Hwj chim FACTOR (Hom.) | PF> 0.97/115VAC, PF> 0.96/230VAC, PF> 0.93/277VAC @ thauj khoom tag nrho
(Thov xa mus rau "POWER FACTOR (PF) CHARACTERISTIC" ntu) |
||||
| TAG NRHO HARMONIC DAB TSI | THD < 20% (@load≧60% / 115VAC, 230VAC; @load≧75% / 277VAC)
(Thov saib mus rau "QHIA HARMONIC DISTORTION" ntu) |
||||
| EFFICIENCY (Tib.) | 88.5% | 90% | 90% | 90.5% | |
| AC CURRENT (Tib.) | 1.3A / 115VAC 0.65A / 230VAC 0.55A / 277VAC | ||||
| INRUSH RUAJ NTSEG (Hom.) | COLD pib 60A (twidth = 520μs ntsuas ntawm 50% Ipeak) ntawm 230VAC; Rau NEMA 410 | ||||
| MAX. TSIS MUAJ. ntawm PSUs ntawm 16A CIRCUIT BREAKER | 4 units (circuit breaker hom B) / 6 units (circuit breaker hom C) ntawm 230VAC | ||||
| TXOJ CAI TSHIAB | 0.25mA / 277VAC | ||||
| TSIS TXAUS SIAB / STANDBY POWER CONSUMPTION | Tsis muaj load zog noj <0.5w rau hom dawb paug; standby zog noj <0.5W rau DA-type/DA2-type | ||||
|
Kev tiv thaiv |
HAUJ LWM | 108 ~ 130% tso zis zog | |||
| Hiccup hom, rov zoo li qub tom qab raug tshem tawm | |||||
| NYIAM QAIB | 12V / 24V hiccup hom thiab 36V / 48V kaw hom (xws li DA-hom / tshwj tsis yog rau DA2-hom) Hiccup hom, rov qab tau txais kev ua txhaum cai raug tshem tawm (tsuas yog rau DA2-hom) | ||||
|
VOL VOLTAGE |
15 ~ 17V | 28 ~ 34V | 41 ~ 46V | 54 ~ 60V | |
| Kaw o/p voltage, rov qhib lub zog kom rov zoo | |||||
| Tshaj kub | Kaw o/p voltage, rov qhib lub zog kom rov zoo | ||||
|
Ib puag ncig |
Ua hauj lwm TEMP. | Tcase = -40 ~ + 90 ℃ (Thov xa mus rau "LOAD LOAD vs TEMPERATURE" ntu) | |||
| MAX. CAS YUAV TSUM | Txc =+90 ℃ | ||||
| Ua hauj lwm HUMIDITY | 20 ~ 95% RH tsis ua-hws | ||||
| KHOOM TEMP., HUMIDITY | -40 ~ +80 ℃, 10 ~ 95% RH | ||||
| TEMP. LEEG THOJ | ± 0.03% / ℃ (0 ~ 45 ℃, tshwj tsis yog 0 ~ 40 ℃ rau 12V) | ||||
| VIBRATION | 10 ~ 500Hz, 5G 12min./1cycle, lub sij hawm rau 72min. txhua tus nrog X, Y, Z axes | ||||
|
SAFETY & EMC |
SAFETY STANDARDS Nco tseg. 5 |
UL8750( type ”HL” )(except for 12DA type), CSA C22.2 No. 250.13-12; ENEC BS EN/EN61347-1, BS EN/EN61347-2-13,
BS EN/EN62384 independent, IP67,BIS IS 15885(Part2/Sec13)(for 12,24 Blank and DA2 Type), EAC TP TC 004, GB19510.1,GB19510.14 approved; Design refer to BS EN/EN60335-1; According to BS EN/EN61347-2-13 appendix J suitable for emergency installations(EL)(AC Input: 100-240Vac)(for DA2-Type only) |
|||
| DALI STANDARDS | IEC 62386-101, 102, 207,251 rau DA / DA2-hom nkaus xwb, Ntaus hom 6 (DT6) | ||||
| Nrog VOLTAGE | I/PO/P: 3.75KVAC; I / P-DA: 1.5KVAC; O / P-DA: 1.5KVAC | ||||
| ISOLATION RESISTANCE | I / PO / P: 100M Ohms / 500VDC / 25 ℃ / 70% RH | ||||
| EMC Kev Ntseeg Nco tseg. 6 | Ua raws li BS EN / EN55015, BS EN / EN61000-3-2 Chav Kawm C (@load≧60%); BS EN/EN61000-3-3, GB/T 17743, GB17625.1; EAC TP TC 020 | ||||
| EMC THAWJ COJ | Ua raws li BS EN / EN61000-4-2,3,4,5,6,8,11; BS EN / EN61547, theem kev lag luam lub teeb (surge tiv thaiv kab-kab 2KV), EAC TP TC 020 | ||||
| Lwm tus | MTBF | 2243.7k h os. Telcordia SR-332 (Bellcore); 228.7K h min. MIL-HDBK-217F (25 ℃) | |||
| DIMENSION | 191 * 63 * 37.5mm (L * W * H) | ||||
| Ntim | 0.97 kg; 15pcs / 15.6Kg / 0.87CUFT | ||||
|
Nco tseg |
1. Txhua qhov tsis hais tshwj xeeb yog ntsuas ntawm 230VAC input, ntsuas tam sim no thiab 25 ℃ ntawm qhov ntsuas kub.
2. De-rating tej zaum yuav xav tau nyob rau hauv qis input voltages. Thov xa mus rau seem "TSHIAB CHARACTERISTIC" kom paub meej. 3. Length of setup time is measured at first cold start. Turning ON/OFF the driver may lead to an increase of the setup time. 4. Tus tsav tsheb raug suav tias yog ib qho khoom siv uas yuav ua haujlwm nrog cov khoom siv kawg. Txij li thaum EMC kev ua tau zoo yuav raug cuam tshuam los ntawm kev teeb tsa tiav, cov khoom siv zaum kawg yuav tsum rov tsim nyog EMC Cov Lus Qhia ntawm kev teeb tsa tiav dua. (raws li muaj nyob rau ntawm https://www.meanwell.com//Upload/PDF/EMI_statement_en.pdf) 5. This series meets the typical life expectancy of >50,000 hours of operation when Tcase, particularly tc point (or TMP, per DLC), is about 75℃or less. 6. Thov xa mus rau daim ntawv lees paub ntawm MEAN WELL's website ntawm http://www.meanwell.com 7. Lub ambient kub derating ntawm 3.5 ℃ / 1000m nrog kiv cua qauv thiab ntawm 5 ℃ / 1000m nrog kiv cua qauv rau kev khiav hauj lwm qhov siab siab tshaj 2000m (6500ft). 8. Rau txhua daim ntawv thov thiab IP dej pov thawj kev ua haujlwm ceev faj, thov xa peb cov neeg siv phau ntawv ua ntej siv. https://www.meanwell.com/Upload/PDF/LED_EN.pdf 9. Raws li IEC 62386-101/102 DALI lub zog ntawm lub sijhawm thiab kev cuam tshuam cov cai, lub sijhawm teeb tsa yuav tsum tau sim nrog DALI tswj uas tuaj yeem txhawb nqa DALI lub zog ntawm kev ua haujlwm, txwv tsis pub lub sijhawm teeb tsa yuav siab dua 0.5 thib ob rau DA hom. ※ Khoom Liability Disclaimer: Yog xav paub ntxiv, thov mus rau https://www.meanwell.com/serviceDisclaimer.aspx |
||||
DIMMING kev ua haujlwm
Dimming txoj cai rau PWM style tso zis
Dimming yog ua tiav los ntawm kev hloov pauv lub luag haujlwm ntawm cov zis tam sim no.
3 hauv 1 dimming muaj nuj nqi (rau Blank-Type)
- Siv ib qho ntawm peb txoj hauv kev ntawm DIM + thiab DIM-: 0 ~ 10VDC, lossis 10V PWM teeb liab lossis tsis kam.
- Dimming qhov tam sim no los ntawm lub hwj chim mov: 100μA (typ.)
Siv cov khoom siv ntxiv 0 ~ 10VDC
Siv cov khoom siv ntxiv 10V PWM teeb liab (ntau zaus 100Hz ~ 3KHz):
Siv additive kuj:
Nco tseg:
- Min. Lub voj voog ua haujlwm ntawm cov zis tam sim no yog kwv yees li 0.15%, thiab cov tswv yim dimming yog li 6KΩ lossis 0.6VDC, lossis 10V PWM teeb liab nrog 6% lub voj voog ua haujlwm.
- Lub voj voog ua haujlwm ntawm cov zis tam sim no tuaj yeem poob mus rau 0% thaum dimming input tsawg dua 6KΩ lossis tsawg dua 0.6VDC, lossis 10V PWM teeb liab nrog lub voj voog ua haujlwm tsawg dua 6%.
DALI Interface (thawj sab; rau DA / DA2-Hom)
- Siv DALI teeb liab ntawm DA + thiab DA-.
- DALI raws tu qauv muaj 16 pawg thiab 64 chaw nyob.
- Thawj kauj ruam yog kho ntawm 0.2% ntawm cov zis
OUTUPUT LOAD vs TEMPERATURE
STATIC CHARACTERISTIC
POWER FACTOR (PF) CHARACTERISTIC
Qhov kub ntawm 80 ℃
TAG NRHO HARMONIC DISTORTION
(THD)
EFFICIENCY vs LOAD
PWM-120 series muaj kev ua haujlwm zoo tshaj plaws uas tuaj yeem ncav cuag 90.5% hauv daim ntawv thov.
Qauv 48V, Tcase ntawm 80 ℃
LUB SIJ HAWM
Thaiv tau Diagram
Mechanical Specification
Pom zoo rau Kev Taw Qhia
Phau ntawv qhia kev teeb tsa
Kev sib txuas rau Blank-type
Ceeb toom
- Ua ntej pib qhov kev teeb tsa lossis kev saib xyuas haujlwm, thov tshem tawm lub zog hluav taws xob los ntawm kev siv hluav taws xob. Xyuas kom meej tias nws tsis tuaj yeem rov txuas tsis tau!
- Keep proper ventilation around the unit and do not stack any objects on it. Also, a 10-15 cm clearance must be kept when the adjacent device is a heat source.
- Mounting orientations other than standard orientation or operating under high ambient temperature may increase the internal component temperature and require a de-rating in output current.
- Qhov ntsuas tam sim no ntawm qhov pom zoo thawj / theem nrab cable yuav tsum ntau dua lossis sib npaug ntawm chav tsev. Thov xa mus rau nws cov specification.
- Rau cov tsav tsheb LED nrog cov khoom siv dej tsis sib haum, xyuas kom meej tias qhov kev sib txuas ntawm chav tsev thiab lub teeb pom kev zoo yog nruj kom cov dej tsis tuaj yeem nkag mus rau hauv lub cev.
- For dimmable LED drivers, make sure that your dimming controller is capable of driving these units.PWM series requires 0.15mA each unit.
- Tc max. is identified on the product label. Please make sure that the temperature of the Tc point will not exceed the limit.
- Tsis txhob txuas "DIM- rau -V".
- Haum rau kev siv sab hauv tsev lossis siv sab nraum zoov yam tsis muaj hnub ci ncaj qha. Thov tsis txhob muab tso rau hauv dej li 30 feeb.
- The power supply is considered a component that will be operated in combination with the final equipment. Since EMC performance will be affected by the complete installation, the final equipment manufacturers must re-qualify EMC Directive on the complete installation again.
FAQ
- Q: Kuv yuav ua li cas yog tias tus tsav tsheb LED tsis ua haujlwm?
A: Txheeb xyuas qhov kev sib txuas ntawm lub zog thiab xyuas kom meej tias qhov voltage source is within the specified range. - Q: Kuv puas tuaj yeem txuas ntau LEDs rau ib tus tsav tsheb?
A: It is recommended to follow the manufacturer’s guidelines on the maximum number of LEDs that can be connected to a single driver to ensure proper functionality and longevity of the LEDs.
Cov ntaub ntawv / Cov ntaub ntawv
 |
MEAN-WELL PWM-120-12 Series Constant Voltage PWM Output LED Driver [ua pdf] Tus tswv phau ntawv PWM-120-12, PWM-120-24, PWM-120-36, PWM-120-48, PWM-120-12 Series Constant Voltage PWM Output LED Driver, PWM-120-12 Series, Constant Voltage PWM Output LED Driver, Voltage PWM Output LED Driver, PWM Output LED Driver, Output LED Driver, LED Driver |