Marquant 014368 Wireless Weather Station

Safety Instructions

Carefully read the instructions before using the product. Save them for future reference.

Symbols

• Read the instructions.
• CE Approved in accordance with the relevant directives.
• [recycle] Recycle discarded product in accordance with local regulations.

Technical Data

Measuring Ranges

Description

This is a wireless weather station that measures humidity, temperature (indoor and outdoor), and air pressure. It displays the weather forecast, time, and weekday. The station is equipped with a calendar, alarm function, frost warning, and snooze function. A wireless temperature sensor is included, offering a range of up to 60 meters over an open space. Batteries are sold separately.

Weather Station Display

• 1. Time
• 2. Outdoor icon
• 3. Week
• 4. Temperature outdoors
• 5. Highest/lowest temperature outdoors
• 6. Highest/lowest humidity outdoors
• 7. Humidity outdoors
• 8. Moon phase
• 9. Barometer pressure for last 12 hours
• 10. RCC icon
• 11. Alarm icon
• 12. Indoor icon
• 13. Calendar
• 14. Temperature indoors
• 15. Weather forecast
• 16. Highest/lowest temperature indoors
• 17. Humidity indoors
• 18. Highest/lowest humidity indoors
• 19. Barometer pressure

Weather Station Buttons and Functions

• 1. MODE button
• 2. ALARM button
• 3. ALERT button
• 4. Button SNOOZE/LIGHT
• 5. UP button
• 6. DOWN button
• 7. Mounting hole
• 8. Support
• 9. DC input
• 10. Battery compartment

Sensor Buttons and Functions

• 1. LCD – temperature
• 2. Status light for signal transfer
• 3. LCD - humidity
• 4. Button °C/°F
• 5. Button TX
• 6. Battery compartment

How to Use

Before First Use

Connect the mains adapter or open the battery compartment on the weather station and insert 2 alkaline AA batteries with the correct polarity as shown by the markings. When the product receives current, all icons on the display light up for 3 seconds, accompanied by an audio prompt. The indoor temperature and humidity are registered. The weather station then starts searching for the outdoor sensor, which takes about 3 minutes. A flashing radio mast icon is shown on the outdoor part of the receiver display during this search. Open the battery compartment on the wireless outdoor sensor and the weather station, and insert 2 alkaline AA batteries with the correct polarity. Once the receiver establishes a connection to the outdoor sensor, it switches to receiving mode for radio-controlled clock setting.

Receiving Radio Signals

The clock automatically searches for a DCF signal 7 minutes after restart or battery replacement. The radio mast icon begins to flash. Automatic synchronization with the DCF signal occurs at 01:00, 02:00, and 03:00 to set the exact time. If synchronization fails (the radio mast icon disappears), a new attempt is made one hour later, repeating up to 5 times.

Manual Search

Start a manual search for a DCF signal by pressing the UP button for 2 seconds. If no signal is received within 7 minutes, the search stops, and a new attempt is made automatically at the next hour. Press the UP button once to cancel the search.

Important Notes on Signal Reception

• A flashing radio mast icon indicates that a DCF signal search is in progress.
• A solid radio mast icon indicates that the DCF signal search was successful.
• Maintain a minimum distance of 2.5 meters from interference sources like TVs or computer screens.
• Radio reception is poorer in basements or rooms with concrete walls. Place the station near a window if reception is poor.
• Only the SNOOZE/LIGHT and UP buttons are active during a DCF signal search. Press the "-" button to stop the search and use other functions.

Manual Setting of Clock

Press and hold the MODE button for 2 seconds. The 12/24 hour indicator will flash. Use UP/DOWN buttons to select 12-hour or 24-hour format. Press MODE to confirm. The temperature unit (°C/°F) will flash; use UP/DOWN to select. Press MODE to confirm. The barometer pressure unit (mbar/hPa/inHg/mmHg) will flash; use UP/DOWN to select. Press MODE to confirm. The time zone value will flash; use UP/DOWN to select (-12 to +12). Press MODE to confirm. The hour value will flash; use UP/DOWN to set. Press MODE to confirm. The minute value will flash; use UP/DOWN to set. Press MODE to confirm. The month and date values will flash; use UP/DOWN to select the display format (month/day or day/month). Press MODE to confirm. The year value (e.g., 2014) will flash; use UP/DOWN to set. Press MODE to confirm. The month value will flash; use UP/DOWN to set. Press MODE to confirm. The date value will flash; use UP/DOWN to set. Press MODE to confirm. The weekday language indicator will flash; use UP/DOWN to select the language. Press MODE to confirm settings and exit. The clock display will be shown. Settings mode closes after 20 seconds of inactivity.

Setting Daily Alarms

Press the ALARM button once; the alarm icon appears, activating the setting mode. Press and hold the ALARM button for 2 seconds. The hour value will flash; use UP/DOWN to set. Press ALARM to confirm. The minute value will flash; use UP/DOWN to set. Press ALARM to confirm and exit. The settings mode closes after 20 seconds of inactivity. The alarm sounds for 2 minutes if not deactivated and repeats automatically after 24 hours. The alarm signal is ascending (2 minutes duration), with volume changing 4 times.

Switching Off the Alarm

Press any button other than SNOOZE/LIGHT to switch off the alarm. The alarm will repeat at the same time the next day.

Snooze Function

Press the SNOOZE/LIGHT button to activate snooze mode. The alarm sounds again after 5 minutes.

Display of Moon Phases

The weather station automatically displays the current moon phase. The phases are indicated as:

• A. New moon
• B. Waxing half moon
• C. Half moon
• D. Waxing full moon
• E. Full moon
• F. Waning full moon
• G. Half moon
• H. Waning half moon

Display of Temperature/Humidity/Barometer Pressure and Trends

The display shows current indoor temperature/humidity/barometer pressure and trends (increasing ⬆️, constant ➡️, decreasing ⬇️). When connected to the outdoor sensor, it also shows outdoor temperature/humidity and trends. The following indications are given:

• Temperature/humidity increasing ⬆️
• Temperature/humidity constant ➡️
• Temperature/humidity decreasing ⬇️

Signal Transfer

When batteries are inserted, the weather station automatically receives signals for temperature and humidity from the outdoor sensor. The outdoor sensor also automatically sends signals. If the station does not receive signals (indicated by - -), press and hold the DOWN button for 3 seconds to manually search for the signal. The icon flashes while receiving.

Display of Highest/Lowest Temperature/Humidity

The display shows the highest (Hi) and lowest (Lo) registered values for temperature and humidity. These values are automatically reset to 00:00 daily.

Important Notes on Limits

• LL,L is displayed if the registered temperature is below the set limit value.
• HH,H is displayed if the registered temperature is over the set limit value.
• LLLL is displayed if the registered barometer pressure is below the set limit value.
• HHHH is displayed if the registered barometer pressure is over the set limit value.

Setting Warning for Outdoor Temperature

Press and hold the ALERT button for 2 seconds until the temperature warning icon flashes. The upper limit icon will flash; use UP/DOWN to set the value and press ALERT to confirm. The lower limit icon will flash; use UP/DOWN to set the value and press ALERT to confirm and exit.

Temperature Warning and Frost Warning

Press the ALERT button briefly to activate/deactivate temperature and frost warnings. If frost warning is active, a symbol appears next to the outdoor temperature, with an audible alarm between -1°C and 3°C (30°F and 37°F). If temperature warning is active, a symbol appears, with an audible alarm at the set limits. Both symbols appear if both warnings are active.

Display of Barometer Pressure in the Last 12 Hours

Press the "+" button repeatedly to view barometer pressure values over the last 12 hours (OHR = current, -1HR = one hour ago, etc.). Settings mode closes after 20 seconds of inactivity.

Weather Forecast Function

It is recommended to check local weather forecasts in addition to the product's forecast. If there are discrepancies, the local forecast is considered more accurate. The product's forecast is based on barometer pressure fluctuations and may differ from actual weather conditions.

Weather Icons

• A. Sun
• B. Partly cloudy
• C. Cloudy
• D. Rain
• E. Heavy rain
• F. Snow
• G. Heavy snow

Note: Weather icons indicate expected changes over the next 8 hours, not the current weather.

Trend for Barometer Pressure

The product can show the predicted trend of barometric pressure with the following indicators:

• Barometric pressure will increase ⬆️
• Barometric pressure will remain unchanged ➡️
• Barometric pressure will drop ⬇️

Backlight

If battery-powered, press SNOOZE/LIGHT for 15 seconds to turn on the backlight. If powered by mains adapter, press SNOOZE/LIGHT to adjust brightness (high/low/off).

Environmental Care

Care for the environment! This product must not be discarded with household waste. It contains electrical or electronic components that should be recycled. Please leave the product for recycling at the designated station, such as the local authority's recycling station.