Hilti HDA-T / -TF / -TR M16 Anchor System
This document provides installation instructions and technical data for the Hilti HDA-T / -TF / -TR M16 anchor system. It details the components, dimensions, installation steps, and safety precautions required for proper use.
Product Overview and Dimensions
The HDA-T / -TF / -TR M16 is a heavy-duty anchor designed for secure fastening in concrete. The diagram illustrates key dimensions:
- hmin: Minimum embedment depth in the base material.
- tfix: Thickness of the fixture being attached.
- hs: Size/depth of the drilled hole.
- df: Diameter of the drilled hole.
Safety icons indicate important user actions:
- ⚠️ ? ?: Observe, Read Manual, Wear Safety Glasses.
Technical Specifications
| HDA-T/-TF/-TR | tfix [mm] min - max | df [mm] | hs [mm] | SW [mm] | Tinst |
|---|---|---|---|---|---|
| M16 × 190/40 | 15 - 40 | 32 | 2 - 8 mm (5/16" - 5/16") | 24 | 120 Nm (89 ft-lb) |
| M16 × 190/60 | 15 - 60 | 32 |
Associated Accessories
| HDA-T/-TF/-TR | Drill Bit | Accessory 1 | Accessory 2 |
|---|---|---|---|
| M16 × 190/40 | TE-Y-HDA-B 30 × 230 | TE-Y-HDA-ST 30-M16 | TE 60 - (04) |
| M16 × 190/60 | TE-Y-HDA-B 30 × 250 | TE 70 - (03)* | TE 70 - (04)* |
*With TE 70:
- hmin = 340 mm - tfix for tfix,max = 40 mm
- hmin = 360 mm - tfix for tfix,max = 60 mm
Installation Instructions
Step 1: Drill Hole
Using a suitable hammer drill and drill bit (e.g., TE-Y-HDA-B), drill a hole into the base material at a 90° angle. Ensure the drill bit diameter (df) and depth are correct as per specifications. Observe safety precautions.
Visual: A drill bit is shown entering a concrete surface at a 90° angle. Icons: ⚠️ [Observe], 90°.
Step 2: Clean Hole
Thoroughly clean the drilled hole of all dust and debris using a brush or vacuum. Proper cleaning is crucial for optimal anchor performance. Red dust particles indicate debris.
Visual: A cleaning tool (brush or blower) is shown removing dust from the drilled hole. Icons: ⚠️ [Observe], ? [Prohibited] (implied by dust removal).
Step 3: Insert Anchor
Insert the Hilti HDA-T anchor into the cleaned hole. The anchor should slide in smoothly. A red arrow indicates the direction of insertion.
Visual: The HDA-T anchor is being pushed into the drilled hole. Red arrow indicates insertion direction.
Step 4: Set Anchor
Use a setting tool (e.g., TE-Y-HDA-ST) to drive the anchor fully into the hole. The tool ensures the anchor is properly seated. A "T" symbol with an arrow indicates the use of a setting tool.
Visual: A setting tool is shown striking the anchor to drive it into the hole. Icon: [Torque Tool] or [Setting Tool], 90° (angle of tool relative to anchor).
Step 5: Position Fixture
Place the fixture (e.g., bracket, steel plate) over the anchor stud. Ensure the fixture is correctly aligned. A red glow may indicate areas of concern or stress.
Visual: The fixture is being placed onto the anchor stud protruding from the concrete. Icons: ⚠️ [Warning], ? [Prohibited] (potential incorrect placement).
Step 6: Tighten Fixture
Install and tighten the nut onto the anchor stud. A close-up view shows the correct seating of the fixture against the anchor head, with a checkmark indicating the correct state and a prohibition symbol for incorrect states.
Visual: A nut is being tightened onto the anchor stud. Close-up shows correct fixture seating (✔️) and incorrect seating (?). Icon: 90° (angle of tightening tool).
Step 7: Dispose of Waste
Dispose of any waste material, such as excess parts or packaging, responsibly.
Visual: A component is being placed into a trash bin. Icon: ?️ [Dispose].
Step 8: Final Torque
Using a calibrated torque wrench, tighten the nut to the specified torque value (Tinst). The spanner width (SW) is also indicated for tool selection.
Visual: A torque wrench is shown tightening the nut to the specified torque (Tinst). Icon: ? [Torque Tool], SW [Spanner Width].
Important Notes and Safety Information
Always observe safety guidelines during installation:
- ⚠️ ?: Pay attention and read the manual thoroughly.
- ?: Always wear appropriate safety glasses.
- ?❌: Do not use a hammer to set the anchor unless specified by the tool.
- ?: Avoid prohibited actions or configurations.
The product is marked with CE and UKCA certification symbols, indicating compliance with relevant standards.
A 3-axis value is provided, likely related to vibration or seismic performance.
Japanese text: "ご使用前に取扱説明書を必ずよくお読み下さい。" which translates to "Please read the instruction manual carefully before use."
HILTI Corp. Feldkircher 100, 9494 Schaan, LI is the manufacturer.
