Overview and Safety Information
This manual provides comprehensive instructions for the assembly and installation of the Traulux SMMI-ROST-VC mobile floor stand. It is designed to support monitors from 60 inches up to 75 inches.
Key Specifications:
- Model: SMMI-ROST-VC
- Maximum TV Size: 60" to 75"
- Maximum TV Weight Capacity: 75 Kg.
- Maximum DVD Shelf Weight Capacity: 5 Kg / 11 lbs
- Maximum Camera Shelf Weight Capacity: 5 Kg / 11 lbs
- VESA Compatibility Patterns: 200x200/300x300, 400x200/400x400, 600x400/800x400, 800x600/1000x600
CAUTION:
- Using products heavier than the indicated rated weights may result in instability and potential injury.
- Follow assembly instructions closely. Improper installation can lead to damage or serious personal injury.
- Safety gear and proper tools are required. Professional installation is recommended.
- Ensure the supporting surface can safely bear the combined weight of the equipment and all attached components.
- Use the provided mounting screws and do not overtighten them.
- This product contains small parts that could be a choking hazard if swallowed. Keep away from children.
- This product is intended for indoor use only. Outdoor use may lead to product failure and personal injury.
Important Note: Read the entire instruction manual before starting installation and assembly. Contact your local distributor for assistance with any questions regarding instructions or warnings.
Component Checklist
Ensure all parts are present before installation. Contact your place of purchase if any parts are missing or faulty.
Main Components:
- A: Left plastic cover
- B: Right plastic cover
- C: Middle base
- D: Universal plate
- E: Top covers
- F: Cable covers
- G: DVD shelf
- H: Left column
- J: Right column
- L: Camera shelf
- M: Connecting plate
- N: Crossbar
- O: Support bar
- P: Left base
- Q: Right base
- R: Butterfly nuts
- S: Butterfly nuts
Hardware:
- T: M8x30 screws
- U: M8x40 screws
- V: M6x14 screws
- W: M6x25 screws
- X: M6x14 screws
- Y: M6x8 screws
- Z: M8x65 screws
- A1: M4x6 screws
- B1: M4x6 screws
- C1: D8 washers
- D1: D6 washers
- M-A: M5x14 screws
- M-B: M6x14 screws
- M-C: M6x30 screws
- M-D: M8x30 screws
- M-E: M8x50 screws
- M-F: Washer
- M-G: Small spacer
- M-H: Big spacer
Tools Included:
- E1: 5mm Allen key
- F1: Wrench
Assembly Instructions
1. Assembling the Base
Attach the right base (Q) and left base (P) to the middle base (C) and secure them using screws (U).
2. Attaching the Columns to the Base
Attach the columns (H, J) to the base using screws (T). To adjust the column height, pull the pin outwards and pull the inner column upwards simultaneously until the desired height is reached, then release the pin to secure. Tighten the safety screw.
Note: Lock the brakes on the casters to prevent unexpected movements during installation. Each caster can be adjusted independently for fine-tuning by slightly turning the nut.
3. Installing the Crossbar
Attach the crossbar (N) to the columns using the appropriate screws (X). Tighten all screws using a Phillips screwdriver. When crossbar installation is complete, tighten the bottom screws using the Allen key (E1).
Note: Press the metal tab to lock the caster.
4. Installing the Cable Covers
The cable covers (F) are installed as part of the cable management process later.
5. Installing the Universal Plate
Attach the universal plate (D) to the columns using the appropriate screws (Z), washers (C1), and butterfly nuts (S). Tighten all screws and butterfly nuts securely.
6. Installing the Adapter Brackets
6a. For Flat Back Screens: Attach adapter brackets using screws like M-A with washers (M-F), or M-B with washers (M-F). Ensure a 1:1 ratio for placement if applicable.
6b. For Screens with Irregular Back: Use screws like M-C/M-D, washers (M-F), and spacers (M-G, M-H) as necessary. Position the adapter brackets as close as possible to the center of the display. Screw the adapter brackets onto the display. Tighten all screws, but do not over-tighten.
7. Hooking the Display onto the Universal Plate
Carefully hook the display onto the universal plate. Tighten the bottom screws to secure the display. IMPORTANT: Ensure the display is mounted correctly and the screws are tightened safely before releasing the display.
8. Installing the Camera Shelf
Attach the camera shelf (L) to the connecting plate (M) using the appropriate screws (B1, A1). Then, attach the connecting plate (M) to the universal plate (D) using screws (W) and washers (D1). Tighten all screws using a Phillips screwdriver.
9. Installing the DVD Shelf
Install the support bar (O) to the columns at the desired position and secure it using the appropriate screws (Y). Attach the DVD shelf (G) to the support bar (O) using screws (W) and butterfly nuts (R). Tighten all screws and butterfly nuts to secure.
10. Cable Management
Route the cables through the cable covers (F) for a tidy installation.
Adjustment
TV height is measured from the floor to the TV center.
It is recommended to adjust the columns to the desired height before installing the display. If you need to adjust the columns height after the display installation is finished, please remove the DVD shelf, then adjust the columns to the desired height.
Maintenance
Check that the bracket is secure and safe to use at regular intervals, at least every three months. Please contact your distributor if you have any questions.
