BAPI BA-RCV-BLE-EZ Wireless Receiver thiab Analog Output Modules Instruction Manual
Tshajview thiab Kev Taw Qhia
Lub Wireless Receiver los ntawm BAPI tau txais cov teeb liab los ntawm ib lossis ntau lub wireless sensors thiab muab cov ntaub ntawv rau Analog Output Modules los ntawm RS485 plaub-xaim npav. Cov modules hloov lub teeb liab mus rau ib qho analog voltage los yog tsis kam rau tus maub los. Lub receiver tuaj yeem ua raws li 32 sensors thiab 127 txawv modules.
Lub Resistance Output Module (ROM) hloov cov ntaub ntawv kub los ntawm lub receiver rau hauv 10K-2, 10K-3, 10K-3 (11K) lossis 20K thermistor nkhaus.
Qhov Voltage Output Module (VOM) hloov cov ntaub ntawv kub lossis av noo los ntawm lub receiver mus rau hauv linear 0 mus rau 5 lossis 0 txog 10 VDC teeb liab. Muaj yim lub Hoobkas teeb tsa qhov kub thiab txias (° F thiab ° C) thiab cov av noo ntawm 0 txog 100% lossis 35 txog 70% RH. Saib daim ntawv lo khoom rau qhov ntau thiab cov zis.
Lub Setpoint Output Module (SOM) hloov cov ntaub ntawv setpoint los ntawm chav wireless sensor rau hauv qhov tsis kam lossis vol.tage. Muaj tsib lub Hoobkas teeb voltage thiab resistive ranges, txhua tus muaj kev xaiv override muaj nuj nqi.
Pairing ntawm Sensor, Receiver thiab Analog Output Modules
Cov txheej txheem kev teeb tsa xav kom txhua lub wireless sensor yog khub rau nws cov neeg txais kev sib txuas thiab tom qab ntawd mus rau nws cov khoom sib txuas lossis cov modules. Cov txheej txheem ua khub yog qhov yooj yim tshaj plaws ntawm lub rooj zaum sim nrog lub sensor, receiver thiab output modules nyob rau hauv sab caj npab ncav cuag ib leeg. Nco ntsoov muab cov cim cim tshwj xeeb rau ntawm lub sensor thiab nws cov khoom tso tawm los yog cov modules tom qab lawv tau ua ke rau ib leeg kom lawv tuaj yeem txheeb xyuas ntawm qhov chaw ua haujlwm.
Yog tias ntau tshaj ib qho kev sib txawv yog kis los ntawm lub sensor (qhov kub thiab txias, av noo thiab setpoint, piv txwv li), txhua qhov sib txawv yuav tsum muaj cov khoom sib cais. Ntau qhov tso zis modules tuaj yeem ua khub rau tib qhov sib txawv yog tias xav tau.
Pairing A sensor rau tus txais
Koj yuav tsum ua ke lub sensor rau lub receiver ua ntej muab lub sensor rau ib qho analog tso zis module.
- Xaiv lub sensor uas koj xav ua khub rau lub receiver. Siv lub zog rau lub sensor. Saib nws phau ntawv qhia kom ntxaws cov lus qhia.
- Siv lub zog rau lub receiver. Lub xiav LED ntawm lub receiver yuav teeb thiab nyob twj ywm.
- Nias thiab tuav lub "Service Button" nyob rau sab saum toj ntawm lub receiver kom txog rau thaum lub xiav LED pib flash, ces nias thiab tso lub "Service Button" ntawm lub sensor (Figs 3 & 4) uas koj xav mus ua khub rau lub receiver. Thaum lub LED ntawm lub receiver rov qab mus rau ib qho khoom "On" thiab ntsuab "Service LED" ntawm lub sensor Circuit Court boards blinks sai sai peb zaug, kev ua khub tiav. Rov ua qhov txheej txheem no rau txhua lub sensors.
Kev sib txuas ib qho kev tawm tswv yim rau lub sensor
Thaum lub sensor txuas rau lub receiver, koj tuaj yeem ua khub tso zis modules rau lub sensor qhov sib txawv.
- Xaiv qhov tso zis module rau qhov xav tau sensor hloov pauv thiab ntau yam thiab txuas mus rau lub wireless receiver (Fig 1).
- Nias thiab tuav lub "Service Button" nyob rau sab saum toj ntawm cov zis module kom txog thaum lub teeb xiav LED pib flash (li 3 vib nas this). Tom qab ntawd, xa ib qho "pairing kis tau tus mob teeb liab" rau qhov tso zis module los ntawm nias thiab tso lub "Service Button" ntawm lub wireless sensor.
Lub xiav LED ntawm lub receiver yuav flash ib zaug qhia tias kis tau tus mob; ces lub xiav LED ntawm qhov tso zis module yuav mus txog li 2 vib nas this thiab tom qab ntawd tua. Lub sensor thiab tso zis module tam sim no tau ua ke rau ib leeg thiab yuav nyob twj ywm ua ke rau ib leeg los ntawm kev hloov roj teeb lossis yog lub zog raug tshem tawm ntawm lub zog xaim
units. Cov zis module lub xiav LED tam sim no yuav flash ib zaug thaum twg nws tau txais kev sib kis ntawm lub sensor.
Nco tseg: Cov wireless sensors feem ntau ntsuas thiab xa tawm ntau yam sib txawv, xws li kub thiab av noo,
los yog kub, av noo thiab setpoint. Tag nrho cov kev hloov pauv no raug xa mus thaum lub sensor "Service Button" raug nias. Txawm li cas los xij, txhua qhov Analog Output Module tau teeb tsa thaum lub sijhawm txiav txim rau ib qho kev sib txawv thiab ntau yam yog li nws tsuas yog khub rau qhov sib txawv thiab tsis yog lwm tus.
Mounting thiab qhov chaw ntawm Antenna
Lub kav hlau txais xov muaj lub hauv paus sib nqus rau mounting. Txawm hais tias tus txais yuav nyob hauv ib lub thawv hlau, lub kav hlau txais xov yuav tsum nyob sab nraum lub thawv. Yuav tsum muaj ib txoj kab uas tsis yog xim hlau pom los ntawm tag nrho cov sensors mus rau lub kav hlau txais xov. Cov kab pom pom muaj xws li cov phab ntsa ua los ntawm cov ntoo, cov ntawv pob zeb lossis plaster nrog cov lath uas tsis yog xim hlau. Kev taw qhia ntawm tus kav hlau txais xov (kab rov tav lossis ntsug) tseem yuav cuam tshuam rau kev ua haujlwm thiab sib txawv raws li daim ntawv thov.
Mounting tus kav hlau txais xov ntawm ib qho chaw hlau yuav txiav tawm kev txais tos los ntawm qab ntawm qhov chaw. Frosted windows tuaj yeem thaiv kev txais tos ib yam nkaus. Ib tug ntoo los yog yas furring sawb txuas rau lub qab nthab beam ua rau ib tug zoo mount. Lub kav hlau txais xov yuav raug dai los ntawm txhua lub qab nthab uas siv fiber ntau lossis yas twine. Tsis txhob siv hlau los dai, thiab tsis txhob siv perforated hlau strapping, feem ntau hu ua plumbers daim kab xev.
Mounting ntawm Receiver thiab Analog Output Module
Lub receiver thiab tso zis modules yuav snaptrack, DIN Rail los yog nto mounted. Txhua tus txais tuaj yeem ua tau txog li 127 modules. Pib nrog lub receiver ntawm sab laug sab laug, tom qab ntawd txuas txhua qhov tso zis module rau sab xis.
Thawb rau hauv xiav mounting tabs rau mount hauv 2.75 ″ snaptrack. Tshem tawm cov mounting tab rau DIN Rail. Catch EZ mount nuv ntawm ntug ntawm DIN rail (Fig 7) thiab tig rau hauv qhov chaw. Tshem tawm cov mounting tabs rau saum npoo mounting siv plaub qhov muab ntsia hlau,
ib lub tab.
Yog tias koj qhov tso zis modules tsis tuaj yeem haum rau hauv ib txoj kab ncaj nraim vim qhov chaw txwv, ces mount ib txoj hlua thib ob ntawm cov qauv saum toj lossis hauv qab. Txuas cov xov hlau los ntawm sab xis ntawm thawj txoj hlua ntawm modules mus rau sab laug ntawm ob txoj hlua ntawm cov modules. Qhov kev teeb tsa no yuav tsum muaj ib lossis ntau dua Pluggable Terminal Block Connector Kits (BA/AOM-CONN) rau cov xov hlau txuas ntxiv ntawm sab laug thiab sab xis ntawm Analog Output Modules.
Txhua cov khoom siv suav nrog ib txheej ntawm 4 connectors.
Kev txiav txim
Lub Wireless Receiver thiab Analog Output Modules yog pluggable thiab tuaj yeem txuas rau hauv ib txoj hlua txuas raws li qhia ntawm txoj cai. Lub hwj chim rau lub tsheb npav tuaj yeem xa mus rau lub receiver lossis mus rau qhov kawg tso zis module ntawm sab xis, tab sis tsis mus rau ob qho chaw tib lub sijhawm. Nco ntsoov tias koj muaj hwj chim txaus rau tag nrho cov khoom siv ntawm lub npav.
Txuas ntxiv RS485 Network nruab nrab ntawm tus txais thiab Analog Output Modules
Analog Output Modules tuaj yeem txuas mus txog 4,000 ko taw deb ntawm lub receiver. Tag nrho ntev ntawm tag nrho cov shielded, twisted khub cables qhia nyob rau hauv daim duab 10 yog 4,000 ko taw (1,220 meters). Txuas cov terminals ua ke raws li qhia hauv daim duab 10. Yog hais tias qhov kev ncua deb ntawm lub receiver mus rau pawg ntawm Analog Output Modules yog ntau tshaj 100 feet (30 meters), muab lub hwj chim cais los yog vol.tage converter (xws li BAPI's VC350A EZ) rau pawg ntawm Analog Output Modules.
Nco tseg: Kev teeb tsa hauv Fig 10 yuav tsum muaj ib lossis ntau dua Pluggable Terminal Block Cov Khoom Siv rau cov hlau txuas ntxiv rau sab laug thiab sab xis ntawm Analog Output Modules. Txhua cov khoom siv suav nrog ib txheej ntawm 4 connectors.
Receiver Hloov Chaw
Tag nrho cov teeb tsa sensor raug tswj thiab hloov kho los ntawm tus neeg txais khoom kom haum raws li qhov xav tau ntawm kev teeb tsa. Cov no raug kho los ntawm DIP keyboards nyob rau sab saum toj ntawm lub receiver. Cov no yog cov chaw rau tag nrho cov SENSORS uas yog khub rau tus txais ntawd.
Sample Rate/Interval Lub sij hawm nruab nrab ntawm thaum lub sensor sawv thiab nyeem ntawv. Qhov muaj nuj nqis 30 sec, 1 min, 3 min lossis 5 min.
Transmit Rate/Interval Lub sij hawm nruab nrab ntawm thaum lub sensor xa cov ntawv nyeem mus rau lub receiver. Cov txiaj ntsig muaj nyob yog 1, 5, 10 lossis 30 feeb.
Delta Temperature Qhov kev hloov ntawm qhov kub thiab txias ntawm sample intervals uas yuav ua rau lub sensor override lub sij hawm kis tau tus mob thiab xa cov hloov kub ntawm lub tom ntej no sample interval. Qhov muaj nuj nqis yog 1 lossis 3 ° F lossis ° C.
Delta Humidity Qhov kev hloov ntawm cov av noo ntawm sample intervals uas yuav ua rau lub sensor override lub transmit interval thiab xa cov av noo hloov nyob rau hauv lub tom ntej no sample interval. Cov txiaj ntsig muaj nyob yog 3 lossis 5% RH.
Rov pib dua Sensor, Receiver lossis Analog Output Module
Sensors, receivers thiab output modules tseem ua ke rau ib leeg thaum lub zog cuam tshuam los yog cov roj teeb raug tshem tawm. Txhawm rau rhuav tshem cov ntawv cog lus ntawm lawv, cov chav nyob yuav tsum tau rov pib dua raws li tau piav qhia hauv qab no:
Txhawm rau rov pib lub sensor: Nias thiab tuav lub "Service Button" ntawm lub sensor li 30 vib nas this. Thaum lub sijhawm 30 vib nas this, lub teeb ntsuab LED yuav tawm li 5 vib nas this, ces nyem maj mam, ces pib flashing sai. Thaum lub flashing ceev nres, rov pib dua tiav. Tam sim no lub sensor tuaj yeem ua khub rau tus txais tshiab. Txhawm rau rov ua khub rau tib lub receiver, koj yuav tsum pib dua lub receiver. Cov zis modules uas yav tas los ua ke rau lub sensor tsis tas yuav tsum tau rov ua khub.
Txhawm rau rov pib dua ib qho kev tawm tswv yim: Nias thiab tuav lub "Service Button" nyob rau sab saum toj ntawm chav tsev li 30 vib nas this. Thaum lub sijhawm 30 vib nas this, lub xiav LED yuav tawm rau thawj 3 vib nas this thiab tom qab ntawd nyem rau lub sijhawm ntxiv. Thaum lub flashing nres, tso lub "Service Button" thiab rov pib dua tiav. Lub tsev tam sim no tuaj yeem rov ua khub rau qhov hloov pauv sensor.
Txhawm rau rov pib dua tus neeg txais: Nias thiab tuav lub "Service Button" ntawm lub sensor li 20 vib nas this. Thaum lub sij hawm 20 vib nas this, lub xiav LED yuav maj mam flashing, ces pib flashing sai. Thaum lub flashing ceev nres thiab rov qab mus rau cov khoom xiav, qhov rov pib dua tiav. Lub tsev tam sim no tuaj yeem rov ua khub rau wireless sensors. Ceev faj! Rov pib dua tus txais yuav rhuav tshem cov ntawv cog lus ntawm lub receiver thiab tag nrho cov sensors. Koj yuav tau rov pib dua txhua lub sensor thiab tom qab ntawd rov ua dua txhua tus sensors rau lub receiver.
Wireless System Diagnostics
Cov teeb meem tshwm sim:
Kev nyeem ntawv los ntawm lub sensor tsis raug lossis ntawm nws qhov kev txwv qis:
Muaj peev xwm daws tau:
- Txheeb xyuas cov kab hluav taws xob kom raug thiab kev sib txuas los ntawm cov khoom tso tawm mus rau tus maub los.
- Txheeb xyuas seb tus maub los lub software puas raug teeb tsa zoo.
- Nias lub khawm "Kev Pabcuam" (raws li tau piav qhia hauv Analog Output Module Pairing seem ntawm pg 1) thiab xyuas kom meej tias cov LED ntsuab ntawm lub sensor Circuit Court board flashes. Yog tsis yog, hloov cov roj teeb.
- Txheeb xyuas lub hwj chim tsim nyog rau lub receiver thiab Analog Output Modules.
LED nyob rau sab saum toj ntawm Analog Output Module yog blinking sai:
- Rov ua dua Analog Output Module raws li tau piav qhia ntawm pg 1, thiab xyuas kom meej tias xiav LED ntawm qhov tso zis module flashes thaum tau txais kev sib kis.
Kev nyeem ntawv sensor tab tom tawm los - Rov ua khub Analog Output Module raws li tau piav qhia ntawm pg 1, thiab xyuas kom meej tias xiav qhov tso zis tsis raug module:
LED ntawm qhov tso zis module flashes thaum kis tau tus mob.
Default Status Thaum Wireless Transmission cuam tshuam
Yog hais tias ib tug tso zis module tsis tau txais cov ntaub ntawv los ntawm nws muab sensor rau 35 feeb, lub xiav LED nyob rau sab saum toj ntawm lub module yuav ntsais sai sai. Yog tias qhov no tshwm sim, tus neeg Analog Output Modules yuav hnov mob raws li hauv qab no:
- Resistance Output Modules (BA/ROM) yuav tso tawm qhov siab tshaj plaws nyob rau hauv lawv cov zis ntau yam.
- Voltage Output Modules (BA/VOM) calibrated rau qhov kub thiab txias yuav teem lawv cov zis rau 0 volts.
- Voltage Output Modules (BA/VOM) calibrated rau cov av noo yuav teeb tsa lawv cov zis rau lawv qhov siab tshaj plawstage (5 lossis 10 volts).
- Setpoint Output Modules (BA/SOM) yuav tuav lawv tus nqi kawg tsis tas li.
Thaum tau txais kev sib kis, cov zis modules yuav rov qab mus ua haujlwm li qub hauv 60 vib nas this lossis tsawg dua.
Txais Specifications
Fais fab mov: 15 mus rau 40 VDC los yog 12 mus rau 24 VAC, halfwave rectified Fais fab mov: 30mA @ 24 VDC, 2.75 VA @ 24 VAC Peev Xwm / Unit: Mus txog 32 sensors thiab 127 sib txawv Analog Output Modules Reception Distance: Varies
Zaus: 2.4 GHz (Bluetooth Tsawg Zog)
Bus Cable nrug: 4,000 ft nrog shielded, twisted khub cable
Kev Ua Haujlwm Ib puag ncig: Temp: 32 txog 140 ° F (0 txog 60 ° C) Cov av noo: 5 txog 95% RH tsis-condensing Enclosure Khoom & Kev Ntsuas: ABS Yas, UL94 V-0 Lub Chaw Haujlwm: RoHS
Analog Output Module Specifications
TAG NRHO MODULES Environmental Operation Range: Kub: 32 ° F txog 140 ° F (0 ° C txog 60 ° C) Vaum: 5% mus rau 95% RH tsis-condensing
Bus Cable nrug: 4,000 ft (1,220m) w / shielded, twisted khub cable
Lub hwj chim: (ib nrab nthwv dej) 15 txog 40 VDC, 12 txog 24 VAC
Cov ntaub ntawv pov thawj & Kev Ntsuas: ABS Yas, UL94 V-0 Lub Chaw Haujlwm: RoHS
SETPOINT OUTPUT MODULE (SOM)
Kev siv fais fab:
Qauv tsis kam:
20 mA @ 24 VDC, 1.55 VA @ 24 VAC
Voltage Qauv:
25 mA @ 24 VDC, 1.75 VA @ 24 VAC
Cov zis tam sim no: 2.5 mA @ 4KΩ load
Poob Comm. Sijhawm:
35 feeb. (Fast Flash)
Rov qab mus rau nws cov lus txib kawg
Analog Input Bias Voltage:
10 VDC max
(Cov qauv tsim tawm tsuas yog siv tau)
Cov zis daws teeb meem:
Resistance tso zis: 100Ω
Voltage tso zis: 150µV
VOLTAGE OTPUT MODULE (VOM)
Kev siv fais fab:
25 mA @ 24 VDC, 1.75 VA @ 24 VAC
Cov zis tam sim no: 2.5 mA @ 4KΩ load
Lost Communication Timeout:
35 feeb. (Fast Flash)
Qhov ntsuas kub tso zis rov qab mus rau 0 volts
% RH cov zis rov qab mus rau qhov ntsuas siab (5V lossis 10V)
Tso zis Voltage Ntau Yam:
0 txog 5 lossis 0 txog 10 VDC (lub Hoobkas calibrated)
Tso zis daws teeb meem: 150µV
RESISTANCE OUTPUT MODULE (ROM)
Kev siv fais fab:
20 mA @ 24 VDC, 1.55 VA @ 24 VAC
Analog Input Bias Voltage: 10 VDC max
Poob Comm. Sijhawm Sijhawm: 35 min. (Fast Flash)
Rov qab mus rau Kev Ua Haujlwm Siab> 35KΩ (Low Temp)
Kub tso zis ntau yam:
10K-2 Chav: 35 txog 120ºF (1 txog 50ºC)
10K-3 Chav: 32 txog 120ºF (0 txog 50ºC)
10K-3 (11K) Unit: 32 txog 120ºF (0 txog 50ºC)
20K Unit: 53 txog 120ºF (12 txog 50ºC)
Cov zis daws teeb meem: 100Ω
Specifications yuav hloov tsis tau ceeb toom.
Module Dimensions
Tsev Automation Products, Inc., 750 North Royal Avenue, Gays Mills, WI 54631 USA Tel: +1-608-735-4800 Ib · Fax+1-608-735-4804 Ib · E-mail:sales@bapihvac.com · Web:www.bapihvac.com
Cov ntaub ntawv / Cov ntaub ntawv
 |
BAPI BA-RCV-BLE-EZ Wireless Receiver thiab Analog Output Modules [ua pdf] Phau ntawv qhia BA-RCV-BLE-EZ Wireless Receiver thiab Analog Output Modules, BA-RCV-BLE-EZ, Wireless Receiver thiab Analog Output Modules, Receiver and Analog Output Modules, Analog Output Modules, Output Modules, Modules, Wireless Receiver, Txais |