Hisense J1-06 Remote Controller
Thank you very much for purchasing this Air Conditioner. Please read this instruction carefully before using this appliance and keep this manual for future reference.
Remote controller
The remote controller transmits signals to the system.
- ON/OFF BUTTON
The appliance will be started when it is energized or will be stopped when it is in operation, if you press this button. - MODE BUTTON
Press this button to select the operation mode. - FAN BUTTON
Used to select fan speed in sequence auto, high, medium or low. - ROOM TEMPERATURE
Used to adjust the room temperature and the timer, also real time. - SETTING BUTTONS
- SMART BUTTON (invalid for some models)
Used to enter fuzzy logic operation directly, regardless of the unit is on or off. 
SWING BUTTON(invalid for some models)
Used to stop or start vertical adjustment louver swinging and set the desired up/down airflow direction.- SLEEP BUTTON
Used to set or cancel Sleep Mode operation. - I FEEL BUTTON
Used to set IFEEL mode operation.
Press it once, the IFEEL function will be started.
Press it again, the IFEEL function will be shut off.
Advice to put the remote controller in the place where the indoor unit receives signal easily.
Advice to cancel the IFEEL mode so as to save energy when stopping the air conditioner. - SUPER BUTTON
Used to start or stop the fast cooling/heating. (Fast cooling operates at high fan speed with 16°C set temp automatically; Fast heating operates at auto fan speed with 30°C set temp automatically) - CLOCK BUTTON
Used to set the current time. - TIMER ON/OFF BUTTON
Used to set or cancel the timer operation. - DIMMER BUTTON (invalid for some models)
When you press this button, all the display of indoor unit will be closed. Press any button to resume display. 
SWING BUTTON (invalid for some models)
Used to stop or start Horizontal adjustment louver swinging and set the desired left/right airflow direction.
Indication symbols on LCD
Note: Each mode and relevant function will be further specified in following pages.
- How to Insert the Batteries
Remove the battery cover according to the arrow direction.
Insert new batteries making sure that the(+) and(-) of battery are matched correctly.
Reattach the cover by sliding it back into position.
Note: - Use 2 LR03 AAA(1.5volt) batteries. Do not use rechargeable batteries.
Replace batteries with new ones of the same type when the display becomes dim. - Storage and Tips for Using the Remote Controller
The remote controller may be stored and mounted on a wall with a holder.
Note: The remote controller holder is an optional part.
- How to Use
To operate the room air conditioner, aim the remote controller to the signal receptor.
The remote controller will operate the air conditioner at a distance of up to 7m when pointing at signal receptor of indoor unit.
CAUTIONS
For appropriate signal transmission between remote controller and indoor unit, keep the signal receiver away from the following items:
- Direct sunlight or other strong lights or heat
- Flat panel television screen or other electrical appliances that react to the remote controller
Additionally, the air conditioner will not operate if curtains, doors or other materials block the signals from the remote controller to the indoor unit. If the signal may not be transmitted properly, either move these materials or consult your local dealer.
Operation instructions
Operation modes
| Range of available set temperature | |
| *HEATING, COOLING | 16ºC ~ 30ºC |
| DRY | -7 ~ 7 |
| FAN ONLY | unable to set |
Note: Heating mode is NOT available for cooling-only models.
Note: At “Dry” mode, the unit can decrease or rise 2°C if you still feel uncomfortable.(For some models you can choose from -7 to 7.)
SWING, SMART, TIMER ON, TIMER OFF, CLOCK, SLEEP and SUPER operation modes will be specified in the following pages.
Changing modes during operation, sometimes the unit does not respond at once. Wait 3 minutes.- During heating operation, air flow is not discharged at the beginning. After 2-5 minutes, the air flow will be discharged until temperature of indoor heat exchanger rises.
- Wait 3 minutes before restarting the appliance.
Airflow direction control (invalid for some models)
|
Airflow direction control |
||||||
| Vertical airflow(Horizontal airflow) is automatically adjusted to a certain angle in accordance with the operation mode after turning on the unit.
*Heating mode is only available for heat pump models. |
|
Vertical airflow control (with the remote controller) |
| Using the remote controller to set various angles of flow or specific angle as you like.
Swinging airflow Desired direction airflow |
|
Horizontal airflow control (with the remote controller) |
| Using remote controller to set various angles of flow or specific angle as you like.
Swinging airflow Desired direction airflow |
NOTE: If the unit doesn’t have four ways airflow function,you can adjust horizontal airflow by yourself. (invalid for some models)
- Do not turn the vertical adjustment louvers manually, otherwise, malfunction may occur. If that happens, turn off the unit first and cut off the power supply, then restore power supply again.
- It is better not to let the vertical adjustment louver tilt downward for a long time at COOLING or DRY mode to prevent condensed water from dripping.
SMART mode (invalid for some models)
Press the SMART button, the unit enters SMART mode(fuzzy logic operation) directly regardless of the unit is on or off. In this mode, temperature and fan speed are automatically set based on the actual room temperature.
For the split-type models, such as wall-mounted air conditioners and some floor-standing air conditioners, their operation mode and set temperature should be determined based on the indoor temperature.
|
Operation mode and temperature are determined by indoor temperature |
|||||||||||||||||||||||||||
| Heat pump models
Cooling only models
|
For commercial air conditioners products, such as cassette-type air conditioners, duct-type air conditioners,ceiling & floor air conditioners and some floor standing air conditioners, their operation mode should be determined based on the difference between the indoor temperature and set temperature.
|
The operation mode is determined by the difference between the indoor temperature and set temperature. |
|||||||||||||||||||||
| Heat pump models
Cooling only models
|
SMART button is ineffective in SUPER mode. Press MODE button cancel SMATR mode.
Note: Temperature, airflow and direction are controlled automatically in SMART mode. However, For the on/off, you can choose from -2 to 2 (for some models you can choose from -7 to 7), for the inverter you can choose from -7 to 7. if you still feel uncomfortable.
|
What you can do in SMART mode |
||
|
Your feeling |
button |
adjustment procedure |
| Uncomfortable because of unsuitable air flow volume. |  |
Indoor fan speed alternates among High, Medium and Low each time this button is pressed. |
| Uncomfortable because of unsuitable flow direction. |  |
Press it once, the vertical adjustment louver swings to change vertical airflow direction. Press it again, swings stops. For horizontal airflow direction, please refer to the previous page for details. |
You can adjust the real time by pressing CLOCK button, then using 
and 
buttons to get the correct time, press CLOCK button again the real time is set.
SUPER mode
|
SUPER mode |
Note:
|
will display on LCD.Timer mode
It is convenient to set the timer on with TIMER ON button when you go out in the morning to achieve a comfortable room temperature at the time you get home. You can also set timer off at night to enjoy a good sleep.
► How to set TIMER ON
TIMER ON button can be used to set the timer programming as wished in order to switch on the appliance at your desired time.
i) Press TIMER ON button, “ON 12:00” flashes on the LCD, then you can press the and buttons to select your desired time for appliance on.
|
|
 |
Press the and button once to increase or decrease the time setting by 1 minute.
Press the and button 2 seconds to increase or decrease the time setting by 10 minute.
Press the and button for a longer time to increase or decrease the time by 1 hour.
Note: If you don’t set the time in 10 seconds after you press TIMER ON button, the remote controller will exit the TIMER ON mode automatically.
ii) When your desired time displayed on LCD, press the TIMER ON button and confirm it.
A “beep” can be heard.
“ON” stops flashing.
The TIMER indicator on the indoor unit lights up.(invalid for some models)
iii) After the set timer displayed for 5 seconds the clock will be displayed on the LCD of the remote controller instead of set timer.
► How to cancel TIMER ON
Press the TIMER ON button again, a “beep” can be heard and the indicator disappears, the TIMER ON mode has been canceled.
Note: It is similar to set TIMER OFF, you can make the appliance switch off automatically at your desired time.
|
SLEEP mode |
|
| SLEEP mode can be set in COOLING, HEATING or DRYING operation mode.
This function gives you a more comfortable environment for sleep.
*Note: In cooling mode, if room temperature is 26″C or above, set temperature will not change(invalid for some models). |
 |
SPECIFICATIONS
|
ON/OFF |
Starts or stops the appliance |
|
MODE |
Selects operation mode |
|
FAN |
Selects fan speed |
|
ROOM TEMPERATURE |
Adjusts room temperature, timer, and real time |
|
SETTING BUTTONS |
N/A |
|
SMART BUTTON |
Enters fuzzy logic operation directly |
|
SWING BUTTON |
Starts or stops vertical and horizontal adjustment louver swinging and sets desired airflow direction |
|
SLEEP BUTTON |
Sets or cancels Sleep Mode operation |
|
I FEEL BUTTON |
Sets IFEEL mode operation |
|
SUPER BUTTON |
Starts or stops fast cooling/heating |
|
CLOCK BUTTON |
Sets current time |
|
TIMER ON/OFF BUTTON |
Sets or cancels timer operation |
|
DIMMER BUTTON |
Closes all display of indoor unit |
|
Indication symbols on LCD |
N/A |
|
Operation modes |
N/A |
|
Range of available set temperature |
N/A |
|
Airflow direction control |
Automatically adjusts to a certain angle in accordance with the operation mode after turning on the unit |
|
SMART mode |
Enters fuzzy logic operation directly, regardless of the unit is on or off |
|
Timer mode |
Sets or cancels timer operation |
FAQS
Press and hold one of the buttons on the remote control. Look at the viewfinder or LCD screen. If the remote control sends a signal, you should see a light in the viewfinder or cellphone screen when you press buttons on the remote control.
On a ductless (split air) air conditioner, the indoor unit can be operated without the remote control by pressing the “Emergency Run” button with a non-metallic pen or pencil. You will find the button in an opening underneath the unit cover on the right side of the case.
It makes any normal AC smart, meaning you can now control your air conditioner using your phone from anywhere, anytime. iOS and Android apps are absolutely free. It adds additional intelligent functionalities and all the benefits of a smart AC for your air conditioner.
By default, the A key is Help, the B key is Day-, the C key is Day+ and the D key is Descriptive Video Service (DVS) on/off.
It is located adjacent to the evaporating coils. Its main responsibility is measuring the temperature of the air in evaporating coils. And it can make the other AC parts to give cool air based on the conditions.
If your air conditioner remote control has passed the point of no return and needs to be replaced, you really should consider obtaining a genuine replacement as opposed to a cheaper and inferior generic or universal remote control.
₹349.00 FREE Delivery on first order.
Even if some of the keys have stopped working or have to be pushed really hard, they can be fixed. The most common problem has to do with the keypad’s conductivity with the circuit board. Open up the remote, clean it out, and apply a new coat of conductive paint to get the keys working again.
The mode button on most remote control devices is to change the channel for wireless transmission.
If your air conditioner remote control has passed the point of no return and needs to be replaced, you really should consider obtaining a genuine replacement as opposed to a cheaper and inferior generic or universal remote control.
If your AC is on cool mode, but still won’t blow cooling air into the room, then check your air filter. It may be dirty, which restricts the air flow in the unit, causing the warm air to flow into your room. Cleaning the filter should help cool the room air.
A firestick with a blue light indicates that the Alexa voice assistant was activated when the microphone button was pressed. Right now, your remote is waiting for a voice command.
Remote controls work with the help of a transmitter that is fitted into the handset. This transmitter sends out a stream pulses of infrared light whenever someone presses a button. The infrared light forms a pattern that is unique to that button, which lets the receiving antenna know how what command to carry out.
Yes, the automatic light sensor is located on the bottom of the TV near the infrared receiver (red light). We apologize for any inconvenience this may cause. If you have any further questions or concerns please give us a call at 1-888-935-8880 or email us at Service@Hisense-usa.com
In most circumstances, it’s usually the remote and 9 times out of 10, you’ll be able to fix it on the spot. So before you get up out of your blanket burrito and start tinkering with the system, here are some simple ways to troubleshoot your AC remote.
The range of available set temperature for heating and cooling modes is 16ºC to 30ºC.
The range of available set temperature for dry mode is -7 to 7.
Do not turn the vertical adjustment louvers manually, otherwise, malfunction may occur. If that happens, turn off the unit first and cut off the power supply, then restore power supply again.
The remote controller can operate the air conditioner at a distance of up to 7m when pointing at signal receptor of indoor unit.
If the signal may not be transmitted properly, either move these materials or consult your local dealer.
SMART mode is a fuzzy logic operation mode that automatically sets temperature and fan speed based on the actual room temperature.
SUPER mode is a fast cooling/heating mode that operates at high fan speed with 16°C set temp automatically for fast cooling, and at auto fan speed with 30°C set temp automatically for fast heating.
You can adjust the real time by pressing CLOCK button, then using and buttons to get the correct time, press CLOCK button again the real time is set.
No, do not use rechargeable batteries. Use 2 LR03 AAA(1.5volt) batteries.
Replace batteries with new ones of the same type when the display becomes dim.
How to use the Hisense Portable Air Conditioner with the Remote Control-Video
Hisense J1-06 Remote Controller Instructions
Documents / Resources
 |
Hisense J1-06 Remote Controller [pdf] Instructions J1-06, Remote Controller, J1-06 Remote Controller |
