HIOS VMS Series Vertical Operation Screwdriver Stands

PRODUCT INTRODUCTION

The Vertical-Operation Screwdriver Stands keep HIOS Screwdrivers in vertical position and help insure normal and efficient operation, thereby minimizing cases of improper fastening screws. When the operator release the driver, it automatically returns to its pre-set position.
The following table shows the respective series of HIOS Screwdrivers that can be used with the three Vertical-Operation Screwdriver Stands.

Caution
Note that HIOS Vertical-Operation Screwdriver Stands cannot be used with screwdrivers made by other manufacturers.

Specifications

Models	VMS-40	VMS-50	VMS-50VZ	Holder Model NO. (order code)
Pole Height	515mm	615mm	615mm
Weight	2.5kg	2.65kg	2.65kg
BL Series	BL-2000/BL-3000/BL-5000		–	VMS40-0180	Standard
CL Series	CL-2000/CL-3000/CL-4000/CL-6500/CL-7000
VZ Series	–		All models (except VZ-1510 Series)	VMS-0900-VZ18
PG Series	–	PG-3000		VMS-0900-PG3	Optional
		PG-5000		VMS-3910-PG5
		PG-7000		VMS-0900-PG7
BLG-ZERO1 Series	BLG-4000ZERO1/BLG-5000ZERO1		–	VMS-0900-BLG45
BLG-BC2 Series	BLG-4000BC2/BLG-5000BC2
BLG-BC1 Series	BLG-4000BC1/BLG-5000BC1
BLG Series	BLG-4000/BLG-5000
BL Series	BL-7000			VMS-0900-BL7
VB Series	–		VB-1510/VB-1510PS	VMS-0910-PG5
			VB-1820/VB-3012	VMS-0900-PG7
			VB-1820PS/VB-3012PS	VMS-0900-VB18PS
VZ Series	VZ-1510/VZ-1510PS		–	VMS50-0190

Screwdriver Stand Parts

Accessories

model	VMS-40 VMS-50	VMS-50VZ
Pole	○	○
Arm Stopper	○	○
Arm-Set	○	○
Pole Holder	○	○
Base	○	○
Ring (for CL-2000)	○	–
L Wench	○	–

External Dimensions

Setup Instructions

1. Attach Pole to Base.
   Use the four Lock screws③ to attach the Pole Holder② to the Base①. Next, insert the Pole ④ into the Pole Holder ② and fix, using the two Pole Lock screws ⑤.
   
2. Attach the screwdriver to Holder.
   1. When using Models VMS-40 and VMS-50
      1. The holes (in the Driver Holder) to be used forattaching the screwdriver depend on the model of screwdriver.
         Please confirm the screwdriver model to be used.
         Applicable Screwdrivers
         

         A	B	C
         CL-2000 BL-2000	CL-3000/4000	BL-3000/5000 CL-6500/7000

         
      2. Remove the Hanger and Driver Cord from the screwdriver before attaching it.
      3. Loosen the two Driver Lock screws ⑦ and set the screwdriver as in the right figure so that the Switch Lever faces the Driver Holder.
      4. It requires a certain amount of force to fit the Driver Connector into the Holder ⑥. Pass the Connector through the Driver Holders.
      5. Align the Driver Holder Lock Screw holes and Hanger Screw holes, then fasten the Driver Lock screws ⑦.
         Attaching CL-2000 Holder
         After setting the screwdriver in step 2-1-4, fit ring onto the connector and connect the Driver Cord.
         Align the Lock Screw holes in the Holder and the Hanger Screw holes, then fasten the Driver Lock screws.
         Attaching VMS-0900-PG7 Holder
         *Spacers are not used on models other than the PG-7000.
         After setting the screwdriver in step 2-1-4, fit ring onto the connector and connect the Driver Cord.
         Align the Lock Screw holes in the Holder and the Hanger Screw holes, then fasten the Driver Lock screws
         
         
   2. When using Model VMS-50VZ
      1. 2-2-1 Remove the Hanger from the VZ Screwdriver and Loosen the Connector Cap. (Fig. 1) 2-2-2 Loosen the two Driver Lock screws and set the driver as in the figure. (Fig. 2)
         Pass the Driver Connector through the Holder and fasten the Connector Cap to fix the driver.
         Align the Lock Screw holes in the Holder and the Hanger Screw holes, then fasten the Driver Lock screws.
         
3. Pass the Pole through the Cylinder⑧, Spring⑨ and Arm Stopper⑩, then fix the Driver Cord in the Cord Snap⑪ to refrain it from interfering operation.
4. To adjust the screwdriver to a comfortable operating height, loosen the Wing nut⑫ and move the Cylinder up or down as necessary.
5. The screwdriver automatically returns to its pre-set position when the operator release it. Its position can be set by adjusting the Arm Stopper.
   

Check that the screwdriver returns to the desired position when it is released. Now it is ready for use.

HIOS Inc.
1-35-1 Oshiage, Sumida-ku Tokyo, Japan 131-0045
TEL: 81-3-6661-8821 FAX: 81-3-6661-8828

Frequently Asked Questions

Q: Can these stands be used with screwdrivers from other brands?

A: No, the stands are only compatible with HIOS Screwdrivers and should not be used with screwdrivers from other manufacturers.

Documents / Resources

HIOS VMS Series Vertical Operation Screwdriver Stands [pdf] Instruction Manual VMS-40, VMS-50, VMS-50VZ, BL-2000, BL-3000, BL-5000, CL-2000, CL-3000, CL-4000, CL-6500, CL-7000, VMS Series Vertical Operation Screwdriver Stands, VMS Series, Vertical Operation Screwdriver Stands, Operation Screwdriver Stands, Screwdriver Stands, Stands

References

• User Manual