HIKVISION DS-K1T341CMW Face Recognition Terminal Instructions

DS-K1T341CMW Face Recognition Terminal

Product Information

Specifications:

  • Product Name: Hikvision DS-K1T341CMW/CMFW Face Recognition
    Terminal
  • Model: DS-K1T341CMW/CMFW
  • Manufacturer: Hikvision
  • Website: www.netdigital.com.au

Product Usage Instructions:

Setting up the DS-K1T341CMW/CMFW with the Bosch Solution 6000
panel

Refer to Page 9 on Bosch Solution 6000 Quick Reference Guide for
detailed setup instructions.

  1. ADD TOKEN: Choose Reader Wi# Keypad #
    Name
  2. Step 7: Present Face to Face Terminal, wait
    for the Read on the Solution 6000.
  3. Step 8: For more faces, repeat Step 5.
  4. Step 9: Press and Hold the Menu Key to
    Exit.

Wiring Diagram:

Wiring Diagram

FAQ (Frequently Asked Questions):

Q: How do I reset the device to factory settings?

A: To reset the device to factory settings, follow these
steps:

  1. Access the device settings menu.
  2. Navigate to the “Reset” or “Factory Reset” option.
  3. Confirm the reset action and wait for the device to
    restart.

Q: Can I connect multiple DS-K1T341CMW/CMFW terminals
together?

A: Yes, you can connect multiple terminals together for a
synchronized access control system. Refer to the user manual for
detailed instructions on setting up multiple terminals.

“`

www.netdigital.com.au

Hikvision DS-K1T341CMW/CMFW Face Recognition Terminal Setting up the DS-K1T341CMW/CMFW with the Bosch Solution 6000 panel

Required Parts: · Hikvision DS-K1T341CMW/CMFW
4.3″ Face Recognition Terminal · Bosch Solution 6000

· CM796B Wiegand to DF RS485 LAN Interface Module

Step 1: On DS-K1T341CMW/CMFW terminal · Activate Device at the Start Up Screen (Follow when prompted) · Keep following prompt to add Admin User

Step 2: · Hold Finger on screen until Swipe Finger Symbol appears, then Swipe Left · Log into Unit with Username and Pass Code · Go to User Icon and Press + · Edit Name · Add Card (this is required) then Press + You can use a generic number here, ie made up number OR
use a MiFare Card. · Press Tick to Save · Add Face and/or Fingerprint Press + to add then (Tick) to Save

Step 3: · Go to Comm Icon · Go to Wiegand – Tap to On and Change from Input to Output, leave as 26 Bit then Press <

Step 4: · Exit Programme

Step 5: On Solution 6000 · Make Sure that you have set up Door Control on the Panel
Refer Pg 9 on Bosch Solution 6000 Quick Reference Guide.

Step 6: Menu 1-2-0 · Select User

ADD TOKEN Choose Reader Wi# Keypad # Name

Step 7: Present Face to Face Terminal, wait for the Read on the Solution 6000.

Step 8: For more faces repeat Step 5.

Step 9: Press and Hold the Menu Key to Exit.

www.netdigital.com.au

Page 1

NetDigital Security | Ph: 03 9558 8088 | Address: 121/45 Gilby Rd, Mount Waverley VIC 3149 | Email: vicsales@netsecurity.com.au | Web: www.netdigital.com.au

Wiring Diagram:

www.netdigital.com.au

www.netdigital.com.au

Page 2

NetDigital Security | Ph: 03 9558 8088 | Address: 121/45 Gilby Rd, Mount Waverley VIC 3149 | Email: vicsales@netsecurity.com.au | Web: www.netdigital.com.au

Documents / Resources

HIKVISION DS-K1T341CMW Face Recognition Terminal [pdf] Instructions
DS-K1T341CMW, DS-K1T341CMW Face Recognition Terminal, Face Recognition Terminal, Recognition Terminal, Terminal

References

Leave a comment

Your email address will not be published. Required fields are marked *