HELIOS 500A Low Voltage Power Advanced FleXbus
Product Information
Specifications:
- Product Name: FleXbus Advanced
- Manufacturer: Helios Power Solutions
- Website: heliosps.com
- Contact Information:
- Australia: sales-au@heliosps.com, +61 2 7200 9200
- Asia: sales@heliosps.asia, +65 6871 4140
- New Zealand: sales-nz@heliosps.com, +64 9 835 0700
- Middle East: sales@heliosps.asia, +971 4 401 8484
Product Usage Instructions:
Fix Supports
Fix half supports directly on the wall, ceiling, or on a cable tray using suitable mounting configurations (Flat/Edge).
Connect FleXbus Conductor
Connect the ready-to-use FleXbus conductor with pre-punched holes on the switchboard.
Install Conductors
Install conductors into the supports and mount the top part of the supports securely.
Strip and Cut Conductor
Strip FleXbus conductor and cut any excess length using appropriate tools like FleXbus Scissors.
Connect to HCBC Clamp
Connect the FleXbus conductor with HCBC clamp and plate for secure connections.
Optional Accessories:
- IP2x Boots for additional protection
- IP55 Conductor Entry for specific requirements
- Fire Barrier for enhanced safety
FAQs:
- Q: Can I use the FleXbus Advanced on any type of surface?
A: Yes, you can fix the supports on the wall, ceiling, or cable tray using appropriate mounting configurations. - Q: Are the optional accessories necessary for installation?
A: The optional accessories like IP2x Boots, IP55 Conductor Entry, and Fire Barrier are recommended for specific use cases to enhance safety and protection.
FleXbus Advanced
Installation Guide
Easy and quick installation sequence overview
- Fix half supports directly on the wall, ceiling or on cable tray
- Connect the ready-to-use FleXbus conductor with pre-punched holes onside switchboard
- Install conductors into the supports and mount the top part of the supports
- Strip FleXbus conductor and cut FleXbus conductor excess length
- Connect FleXbus conductor with HCBC clamp and plate
- Optional IP2x Boots
- Optional IP55 Conductor Entry
- Optional Fire Barrier
Fix supports directly on the wall, ceiling or on cable tray (wire basket/perforated/cable ladder). Use multiple possible mounting configurations to fit your installation
(Flat/Edge)
Connect the ready-to-use FleXbus conductor with pre-punched holes to the switchboard. This connection can be made directly onto the busbar or circuit breaker with optional palm extenders 
Install conductors into the supports and mount the top part of the supports. Leave excess conductor length at the top of the transformer/power supply. 
Strip FleXbus conductor. Cut excess length of the FleXbus with scissosor shears
Connect FleXbus conductor with HCBC clamp and plate
Optional IP2x Boots 
Optional IP55 Conductor Entry 
Optional Fire barrier 
Australia
sales-au@heliosps.com
+61 2 7200 9200
Asia
sales@heliosps.asia
+65 6871 4140
New Zealand
sales-nz@heliosps.com
+64 9 835 0700
Middle East
sales@heliosps.asia
+971 4 401 8484
Our powerful portfolio of brands
CADDY ERICO HOFFMAN RAYCHEM SCHROFF TRACER
©2021 nVent. All nVent marks and logos are owned or licensed by nVent Services GmbH or its affiliates. All other trademarks are the property of their respective owners.
nVent reserves the right to change specifications without notice.
ERIFLEX-IM-H86996-InstallationManual-ML-2112
Documents / Resources
 |
HELIOS 500A Low Voltage Power Advanced FleXbus [pdf] Installation Guide 500A, 500A Low Voltage Power Advanced FleXbus, Low Voltage Power Advanced FleXbus, Power Advanced FleXbus, Advanced FleXbus, FleXbus |
