User Manual

---

Automatic barcode reader with stand
HD10C

Specification

• Light source: 620nm LED
• Sensor Type: CMOS
• Scanning method: manual (on the button) / automatically (after the code is brought closer)
• Scan confirmation: light and sound signal
• Scanning speed: 200 times/second
• Interface: USB
• Cord length: 140 cm
• Protection level: IP54
• Device dimensions: 16 x 9.5 x 6.5 cm
• Base dimensions: 24 x 12 x 12 cm
• Package dimensions: 18.5 x 12 x 8.5 cm
• Weight: 300 g
• Package weight: 370 g
• Operating temperature: -20 – 50°C
• Storage temperature: -40 – 60°C
• Read 1D codes: EAN-8, EAN-13, UPC-A, UPC-E, CODE 128, CODE 39, CODE 93, CODE 11, CHINESE 2 of 5, CODABAR, MSI, Interleaved 2 of 5 (ITF), others one-dimensional

The set contains:

• Barcode Reader
• Reader stand for self-assembly
• Built-in USB communication cable
• Manual

Features:

• Wired reader for scanning standard barcodes
• Scan codes on LCD, LED/OLED and mobile device displays
• Barcode scanning in automatic mode
• Any character can be programmed before or after the code

Factory reset

Restore default settings
Code Scanning Modes
Manual mode	Automatic mode
Beep settings
Sound On (default)	Sound off
Setting trailing characters
CR	Unmarked
TAB	LF+CR
Case settings
Uppercase and lowercase letters	No case conversion
Uppercase letters only	Lowercase only
Reading inverted codes (on a black background)
Enabled	Off (default)

Add a prefix and suffix
Add Prefix	Add a suffix
Cancel prefix	Anuluj suffix
Save settings
To set a prefix or suffix, first scan the code “Add a prefix” or “Add a suffix”, then scan the appropriate character from the table at the end of this manual, and finally read the code “Save settings”.

Hide barcode characters
Hiding Initial Characters	Hide trailing characters
In order to hide individual characters in the barcode, first scan the code “Hide Leading Characters” or “Hide Trailing Characters” and then read the code at the end of this manual, corresponding to the number of digits to hide, with the scanner. For example, if you want to hide the first two characters of a barcode, you must first scan the code “Hide Initial Characters”, then scan the code “0” and “2” from the table.

Character Table

SOH	STX	ETX
EOT	ENQ	ACK
BEL	Backspace	TAB
LF	VT	FF
CR	SO	SI
DLE	DC1	DC2
DC3	DC4	NAK
SYN	ETB	CAN
EM	SUB	ESC
FS	GS	RS
US	SPACE	!
“	#	$
%	&	‘

(	)	*
+	,	–
.	/	0
1	2	3

4	5	6
7	8	9
:	;	<
=	>	?
@	A	B
C	D	I
F	G	H
I	J	K
L	M	N

O	P	Q
R	S	T
U	V	W

X	Y	Z
[	\	]
^	_	‘
a	b	c
d	e	f
g	h	i
j	k	l
m	n	o
p	q	R
s	t	u

v	w	x
y	z	{
|	}	~
Delete	F1	F2
F3	F4	F5
F6	F7	F8
F9	F10	F11
F12	INSERT	HOME
Page Up	Delete	END
Page Down	Right arrow	Left arrow
Bottom arrow	Top arrow

---

hdwrglobal.com

Documents / Resources

HDWR HD10C Automatic Barcode Reader with Stand [pdf] User Manual HD10C Automatic Barcode Reader with Stand, HD10C, Automatic Barcode Reader with Stand, Barcode Reader with Stand, Reader with Stand, Stand

References

• User Manual