Split Inground Light Installation Instructions
Product Specifications | ||
Model No. | HV1845T | HV1845RGBW |
Name | Split | |
Material | 316 Stainless Steel | |
Colour | Stainless Steel | |
IP Rating | IP67 | |
Input Voltage | 12v DC | |
Protection Class | ![]() |
|
Lamp Base | Built-In LED | |
Lamp Wattage | 1 x 18w | |
Colour Temp | TRI Colour – 3000k, 4000k, 5500k | RGBW (RGB + 3000K) |
Lumens | 12001m, 12901m, 13501m | 5501m (3000k) |
CRI | > 80 | |
Wiring | Parallel | |
Dimmable | No | Yes with RGBW Controller |
Warranty | 3 Years Replacement* |
Dimensions | Adequate Drainage |
![]() |
![]() |
Steps for Installation: HV1845T
- Make sure that the electrical circuit is free of voltage (master switch off)
- Make a hole where the fitting is to be placed using dimensions provided on line drawings, making sure adequate drainage is allowed.
- Insert the canister, and ensure that the top is level with the ground or floor. Failure to do so will void the warranty.
- Using an appropriate 12v DC LED Driver – DO NOT CONNECT LIGHT FITTING DIRECTLY TO 240V
- Connect the cable – If more than one fitting is installed, wiring must be done in parallel.
- Strip back the cable on both fitting and cable run and twist the positive cables together. Then connect neutral cables together
- Solder all joins using solder and either a heat gun or butane gas torch.
- Cover connections using an adhesive-lined heat shrink or gel cap to make the connection watertight. Failure to do this will void the warranty.
- Heat the heat shrink or crimp the gel cap making sure all connections are covered.
- Make sure the seals are still in place and screws are tight to avoid any water penetration.
- Fitting is preset to 3000k, locate cap on the bottom of fitting and remove by twisting anti-clockwise, Slide switch to desired colour temperature, Reattach cap making sure it is tight.
- Insert fitting into the canister.
- Apply silicon around edge of the fitting to prevent any water from getting inside to electrical connections.
- All connections must be carried out carefully, inspect all contacts before switching back on the electric circuit.
Steps for Installation: HV1845RGBW
- Make sure that the electrical circuit is free of voltage (master switch off)
- Make a hole where the fitting is to be placed using dimensions provided on line drawings, making sure adequate drainage is allowed.
- Insert the canister, and ensure that the top is level with the ground or floor. Failure to do so will void the warranty.
- Connect the cable –
- Use an appropriate 12v DC LED Driver and RGBW LED Controller- DO NOT CONNECT LIGHT FITTING DIRECT TO 240V
- Do this by stripping back the cable on both fitting and cable run and twisting the cable together making sure all colours are correctly joined to the correct colour-
- Black= Positive
- Red = Red
- Green = Green
- Blue = Blue
- White = White
- Solder all joins using solder and either a heat gun or butane gas torch.
- Cover connections using an adhesive-lined heat shrink or gel cap to make the connection watertight. Failure to do this will void the warranty.
- Heat the heat shrink or crimp the gel cap making sure all connections are covered.
- Connect cable run to RGBW Controller.
- Connect the RGBW Controller to a 12v DC LED Driver.
- Apply silicon around the edge of the fitting to prevent any water from getting inside to electrical connections.
- All connections must be carried out carefully, inspect all contacts before switching back on the electric circuit.
Steps for Installation: HV1845-F-SH
- Remove nuts on the back of the fitting and set aside
- Remove cover and replace with security face
- Reattach nuts and tighten making sure seals are still in place
- Insert fitting into the canister
- Insert screws and tighten
Must be installed by a licensed electrician
Contact Details:
143 Beauchamp Road | Tel: 02 9381 8300 |
Matraville NSW 2036 | Fax: 02 9666 8881 |
Australia | Email: sales@havit.com.au |
Web: www.havit.com.au |
Warranty Terms & Conditions* | Additional Information |
![]() |
![]() |
https://havit.com.au/pages/warranty-terms-and-conditions | https://havit.com.au/ |
Documents / Resources
![]() |
HAVIT Lightning HV1845T Split Inground Light [pdf] Instruction Manual HV1845T, Split Inground Light, HV1845T Split Inground Light, Inground Light, Light |