HANYOUNG logoNUX HSR-2D-2A Single Phase Solid State Relay
Instruction Manual

HSR-2D-2A Single Phase Solid State Relay

HANYOUNG NUX HSR 2D 2A Single Phase Solid State RelaySingle-Phase Solid State Relay
HSR-2D/2A
INSTRUCTION MANUAL

Thank you for purchasing Han young Nix products. Please read the instruction manual carefully before using this product, and use the product correctly. Also, please keep this instruction manual where you can view it any time.

Safety information

Please read the safety information carefully before the use, and use the product correctly.
The alerts declared in the manual are classified into Danger, Warning and Caution according to their importance
DANGER Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury
WARNING Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury
CAUTION Indicates a potentially hazardous situation which, if not avoided, may result in minor injury or property damage

DANGER
The input/output terminals are subject to electric shock risk. Never let the input/output terminals come in contact with your body or conductive substances.
WARNING

  • When used in equipment with a high risk of personal injury or property damage (examples: medical devices, nuclear control, ships, aircrafts, vehicles, railways, combustion devices, safety devices, crime/disaster prevention  equipment etc.) install double safety devices and prevent accidents. Failure to do so may result in fire, personnel accident or property damage.
  • Please read the safety information carefully before the use, and use the product correctly.
  • If there is a possibility that a malfunction or abnormality of this product may lead to a serious accident, install an appropriate protection circuit on the outside and plan to prevent accidents.
  • Please supply the rated power voltage, in order to prevent product breakdowns or malfunctions.
  • To prevent electric shocks and malfunctions, do not supply power until the wiring is completed.
  • Please disassemble the product after turning OFF the power.
  • Any use of the product other than those specified by the manufacturer may result in personal injury or property damage.
  • Please use this product after installing it to a panel, because there is a risk of electric shock.

CAUTION

  • Please make sure that the product specifications are the same as you ordered.
  • Please use the product in places where corrosive gases (especially harmful gases, ammonia, etc.) and flammable gases are not generated.
  • Please use the product in places without liquids, oils, chemicals, steam, dust, salt, iron, etc. (pollution degree 1 or 2).
  • Please avoid places where large inductive interference, static electricity, magnetic noise are generated.
  • Please avoid places with heat accumulation caused by direct sunlight, radiant heat, etc.
  • When water enters, short circuit or fire may occur, so please inspect the product carefully.
  • Do not connect anything to the unused terminals.
  • For DC types, please wire correctly, after checking the polarity of the terminals.
  • When using the SSR, the product may be damaged if the specified heat sink is not used. Be sure to use the specified heat sink.
  • When disposing of the product, treat it as industrial waste.

Suffix code

Model Code Content
 HSR HANYOUNG NUX HSR 2D 2A Single Phase Solid State Relay - icon HANYOUNG NUX HSR 2D 2A Single Phase Solid State Relay - icon HANYOUNG NUX HSR 2D 2A Single Phase Solid State Relay - icon HANYOUNG NUX HSR 2D 2A Single Phase Solid State Relay - icon HANYOUNG NUX HSR 2D 2A Single Phase Solid State Relay - icon HANYOUNG NUX HSR 2D 2A Single Phase Solid State Relay - icon Single-Phase Solid State Relay
Control phase 2 Single-phase
Icnopnutrtol voltage D 4 – 32 VDC
A 90 – 264 VAC
 

Rated load current

10 10 A
20 20 A
30 30 A
40 40 A
50 50 A
70 70 A
Rated load voltage 2 90 – 264 VAC
4 90 – 480 VAC
Operation method (switching mode) Z Zero cross switching
R Random switching
Heat sink Without heat sink
-T With heat sink (only for 50A, 70A)

Specifications

■ DC input type (low voltage)

Classification HSR-2D102Z HSR-2D202Z HSR-2D302Z HSR-2D402Z HSR-2D502Z HSR-2D702Z
HSR-2D102R HSR-2D202R HSR-2D302R HSR-2D402R HSR-2D502R HSR-2D702R
 

Input

Power voltage Operating 5 – 24 VDC
voltage range Impedance 4 – 32 VDC Max. 4 ㏀
Operating voltage Min. 3 VDC
Reset voltage Max. 1.5 VDC
Input current Constant current method: 10 ㎃ (±3)
Rated load voltage 100 – 240 VAC
 

 

Output

Rated load voltage 90 – 264 VAC
Load voltage range 90 – 480 VAC
Peak voltage
(non-repetition)
800 V 1200 V 1200 V 1200 V 1200 V 1200 V
Rated load current 10 A 20 A 30 A 40A 50A 70A
Frequency 50/60㎐
Surge current 170A 250 A 350 A 370 A 580 A 580 A
Leakage current Max. 20 ㎃ Max. 20 ㎃ Max. 20 ㎃ Max. 20 ㎃ Max. 20 ㎃ Max. 20 ㎃
ON state voltage drop 1.3 V 1.6 V 1.8 V 1.8 V 1.8 V 1.8 V
Min. operating current 1 A 1 A 1 A 1 A 0.5 A 0.5 A
Response
speed
Zero cross switching 1/2 cycle +1 ㎳ max.
Random switching Max. 1 ms
Insulation resistance 500 VDC, 100 ㏁ (input/output and among cases)
Dielectric strength 2500 VAC (60 ㎐ for one minute)
Vibration resistance 10 – 55 ㎐, double amplitude: 1.5 ㎜, Each X· Y· Z axis for 2 hours
Shock resistance 1000 ㎨ (about 100 G), Each X· Y· Z axis for 3 times
Storage temperature -30 ~ 90 ℃
Ambient temperature & humidity -20 ~ 80 ℃, 45 ~ 85 % R.H.
Approval CE SYMBOL
Weight (g) 150

※ Weight when packed
DC input type (high voltage)

Classification HSR-2D104R HSR-2D204R HSR-2D304R HSR-2D404R HSR-2D504R HSR-2D704R
HSR-2D104R HSR-2D204R HSR-2D304R HSR-2D404R HSR-2D504R HSR-2D704R
 

Input

Power voltage
Operating
5 – 24 VDC
voltage range 4 – 32 VDC
Impedance Max. 4 ㏀
Operating voltage Min. 3 VDC
Reset voltage Max. 1.4 VDC
Input current Constant current method: 10 ㎃ (±3)
 

 

Output

Rated load voltage 100 – 440 VAC
Load voltage range
Peak vole age
90 – 480 VAC
(non-repetition) 800 V 1200 V 1200 V 1200 V 1200 V 1200 V
Rated load current 10 A 20 A 30 A 40 A 50 A 70 A
Frequency 50/60 ㎐
Surge current 170 A 250 A 350 A 370 A 580 A 580 A
Leakage current Max. 20 ㎃ Max. 20 ㎃ Max. 20 ㎃ Max. 20 ㎃ Max. 20 ㎃ Max. 20 ㎃
ON state voltage drop 1.3 V 1.6 V 1.8 V 1.8 V 1.8 V 1.8 V
Min. operating current 1 A 1 A 1 A 1 A 0.5 A 0.5 A
Ressppeoendse Zero cross switching 1/2 cycle + 1 ㎳ max.
Random switching Max. 1 ms
Insulation resistance 500 VDC, 100 ㏁ (input/output and among cases)
Dielectric strength 2500 VAC (60 ㎐ for one minute)
Vibration resistance 10 – 55 ㎐, double amplitude: 1.5 ㎜, Each X· Y· Z axis for 2 hours
Shock resistance 1000 ㎨ (about 100 G), Each X· Y· Z axis for 3 times
Storage temperature -30 ~ 90 ℃
Ambient temperature & humidity -20 ~ 80 ℃, 45 ~ 85 % R.H.
Approval CE SYMBOL
Weight (g) 150

※ Weight when packed
■ AC input type (low voltage)

Classification HSR-2A102Z HSR-2A202R HSR-2A302R HSR-2A402R HSR-2A502R HSR-2A702R
HSR-2A102R HSR-2A202R HSR-2A302R HSR-2A402R HSR-2A502R HSR-2A702R
 

Input

Power voltage Operating 100 – 240 VAC
voltage range 90 – 264 VAC
Impedance Max. 40 ㏀
Operating voltage Min. 72 VAC Min. 72 VAC Min. 72 VAC Min. 72 VAC Min. 75 VAC Min. 75 VAC
Reset voltage Max. 40 VAC
Input current 240 VAC / 9 ㎃(±4)
 

 

Output

Rated load voltage 100 – 240 VAC
Load voltage range 90 – 264 VAC
Peak voltage
(non-repetition)
600 V 600 V 600 V 600 V 800 V 800 V
Rated load current 10 A 20 A 30 A 40 A 50 A 70 A
Frequency 50/60 ㎐
Surge current 170 A 250 A 350 A 370 A 580 A 580 A
Leakage current 15 ㎃ 15 ㎃ 15 ㎃ 15 ㎃ Max. 20 ㎃ Max. 20 ㎃
ON state voltage drop 1.3 V 1.6 V 1.8 V 1.8 V 1.8 V 1.8 V
Min. operating current 1 A 1 A 1 A 1 A 0.5 A 0.5 A
Response
speed
Zero cross switching 1/2 cycle +1 ㎳ max.
Random switching Max. 1 ms
Insulation resistance 500 VDC, 100 ㏁ (input/output and among cases)
Dielectric strength 2500 VAC (60 ㎐ for one minute)
Vibration resistance 10 – 55 ㎐, double amplitude: 1.5 ㎜, Each X· Y· Z axis for 2 hours
Stock resistance e

orange temperature

1000 ㎨ (about 100 G), Each X· Y· Z axis for 3 times

-30 ~ 90 ℃

Ambient temperature & humidity -20 ~ 80 ℃, 45 ~ 85 % R.H.
Approval CE SYMBOL
Weight (g) 150

■ AC input type (high voltage)

Classification HSR-2A104Z HSR-2A204Z HSR-2A304Z HSR-2A404Z HSR-2A504Z HSR-2A704Z
HSR-2A104R  HSR-2A204R HSR-2A304R HSR-2A404R HSR-2A504R HSR-2A704R
 

Input

Power voltage 100 – 240 VAC
Operating voltage range 90 – 264 VAC
Impedance Max. 4 ㏀
Operating voltage Min. 80 VAC Min. 80 VAC Min. 80 VAC Min. 80 VAC Min. 75 VAC Min. 75 VAC
Reset voltage Max. 40 VAC
Input current 240 VAC / 9 ㎃(±4)
 

 

Output

Rated load voltage 100 – 440 VAC
Load voltage range 90 – 480 VAC
Peak voltage
(non-repetition)
800 V 1200 V 1200 V 1200 V 1200 V 1200 V
Rated load current 10 A 20 A 30 A 40 A 50 A 70 A
Frequency
Surge current
170 A              250 A              350 A 50/60 ㎐ 370 A             580 A              580 A
Leakage current Max. 20 ㎃ Max. 20 ㎃ Max. 20 ㎃ Max. 20 ㎃ Max. 20 ㎃ Max. 20 ㎃
ON state voltage drop 1.3 V 1.6 V 1.8 V 1.8 V 1.8 V 1.8 V
Min. operating current 1 A 1 A 1 A 1 A 0.5 A 0.5 A
Ressppeoendse Zero cross switching 1/2 cycle + 1 ㎳ max.
Random switching Max. 1 ms
Insulation resistance 500 VDC, 100 ㏁ (input/output and among cases)
Dielectric strength 2500 VAC (60 ㎐ for one minute)
Vibration resistance 10 – 55 ㎐, double amplitude: 1.5 ㎜, Each X· Y· Z axis for 2 hours
Shock resistance 1000 ㎨ (about 100 G), Each X· Y· Z axis for 3 times
Storage temperature -30 ~ 90 ℃
Ambient temperature & humidity -20 ~ 80 ℃, 45 ~ 85 % R.H.
Approval CE SYMBOL
Weight (g) 150

Dimensions

HANYOUNG NUX HSR 2D 2A Single Phase Solid State Relay - Dimensions

HEAT SINK

■ Model name: HSP series

HANYOUNG NUX HSR 2D 2A Single Phase Solid State Relay - HEAT SINK+

Model Applicable Model Capacity(A) Weight
HSP-10 HSR-2E110EID 10 A 208 g

HANYOUNG NUX HSR 2D 2A Single Phase Solid State Relay - HEAT SINK 1

Model Applicable Model Capacity(A) A B C Weight
HSP-20 HSR-2120❑❑ 20 A 85.0 60. 85.0 404 g
HSP-40 HSR-20300❑ 30 A 114.0 60. 114.0 570 g
HSR-2❑40❑40 A

Model name: HSM series

HANYOUNG NUX HSR 2D 2A Single Phase Solid State Relay - HSM series

Model Applicable Model Capacity(A) A BCD E Weight
HSM-70 HSR-2010❑❑ 10 A 70.0 35.0 49. 364 g
I-ISM 110 HSR-2 M 20E10 20A 110.0 55.0 49. 568g
HSR-2❑30❑❑ 30 A
HSM-150 HSR-274000 40A 150.0 75.0 49. 97.0 32.0 768g

Model name: HSN80-F series

HANYOUNG NUX HSR 2D 2A Single Phase Solid State Relay - series

■ Model name: HSN120-F series

HANYOUNG NUX HSR 2D 2A Single Phase Solid State Relay - series1

Model Applicable Model Capacity(A) Weight
HSN80-F HSR-2050❑❑ 50A 1,474g
HSN120-F HSR-2770❑❑ 70A 2,052g

The above contents are subject to change without prior notice for performance improvement.

Application circuits

AC input type (10 A ~ 40 A)HANYOUNG NUX HSR 2D 2A Single Phase Solid State Relay - circuitsEquivalent circuits

HANYOUNG NUX HSR 2D 2A Single Phase Solid State Relay - Equivalent

Load Current Characteristics

■ Input Voltage / Current Characteristics
HANYOUNG NUX HSR 2D 2A Single Phase Solid State Relay - Load Current

■ Load Current Characteristics

HANYOUNG NUX HSR 2D 2A Single Phase Solid State Relay - Load Current1

■ Surge Current Characteristics
HANYOUNG NUX HSR 2D 2A Single Phase Solid State Relay - Surge Current

■ Precautions while using the heat sinks
HANYOUNG NUX HSR 2D 2A Single Phase Solid State Relay - heat sinks

  • Using standard heat sink and heat-dissipation grease is mandatory for this product.
  • Even the standard heat sink is used, HSR damage may occur if the environment temperature rises or if the ventilation does not work well (environment temperature : over 40 °C)
  • The normal HSR element is damaged at the maximum temperature of 125 °C or more. When the temperature of heat sink is 85 ° C or higher, or more, the temperature of the element reaches around 125 °C. Therefore, during operation, measure the temperature of heat sink.
  • When you connect HSR to the heat sink, heat-transmitting grease is needed for smooth heat transmission.
  • To prevent separation by vibration, tighten up with bolts.
  • Before installation, be sure to apply heat-dissipation grease to the contact surface i using the standard heat sink, as shown in the above picture. Do not use on insulation boards (wood, plastic, rubber)
    For further information, please visit our homepage (www.hanyoungnux.com) and refer to the user’s manual in the archive.

HANYOUNG logoHANYOUNGNUX CO.,LTD
28, Gilpa-ro 71beon-gil, Michuhol-gu,
Incheon, Korea TEL : +82-32-876-4697
http://www.hanyoungnux.com
MC1001KE220701

Documents / Resources

HANYOUNG NUX HSR-2D-2A Single Phase Solid State Relay [pdf] Instruction Manual
HSR-2D-2A, HSR-2D-2A Single Phase Solid State Relay, Single Phase Solid State Relay, Phase Solid State Relay, Solid State Relay, State Relay, Relay

References

Leave a comment

Your email address will not be published. Required fields are marked *