HAMMER WORKPAD LTE Tablet User Manual

HAMMER WORKPAD LTE Tablet

Setup and use

1. Before first start: switch off the tablet before installing cards.
2. Install SIM/microSD: open the SIM/microSD tray (top of casing, right-hand side). Ensure the nanoSIM is correctly positioned, then slide the tray back in.
3. Charge the battery: connect the USB‑C plug to the device and the USB plug to the charger, then plug the charger into a wall socket.
4. Use the strap (included): unclip quick-release fasteners from both strap ends, thread the cord through the loop in the pad, pull the fastener through the loop formed by the cord, snap fasteners back to the ends, then adjust length using the buckle.
5. Basic screen control: touch to open options/apps, swipe to scroll, triple-click for zoom (if enabled), and hold+swipe to delete/uninstall an element.
6. Turn off the screen: press the blockade button (the screen also turns off after inactivity).
7. eSIM (if needed): ensure an internet connection (Wi‑Fi or cellular data), then go to Settings → Mobile Network/eSIM and follow the eSIM profile setup/activation using the carrier’s QR code.

Safety

Attention

Statement

The manufacturer is not responsible for any consequences caused by improper use of the device and not following the above instructions.

The software version can be upgraded without prior notice.

• Read these guidelines carefully. Not following them may be dangerous or illegal.

DO NOT RISK

• All wireless devices may cause interference, which could affect the performance of other devices. Do not switch on the device when the use of mobile phones is prohibited or if it might cause interference or danger.

ROAD SAFETY

• Do not use this device while driving any kind of vehicle.

RESTRICTED AREAS

• Switch OFF the device in an airplane since it may disturb the operation of other equipment located therein. The device may interfere with the operation of medical equipment in hospitals and health protection entities.
• Abide by any kinds of prohibitions, regulations, and warnings conveyed by the medical staff.

PETROL STATIONS

• Always turn off the device while refuelling your car at a petrol station. Do not use your device close to chemicals.

WI-FI (WLAN)

• In the European Union Member States, a WLAN network may be used indoors without any restrictions. In France, a WLAN network may not be used outdoors.

QUALIFIED SERVICE

• Only qualified personnel or an authorized service center may install or repair this product. Repairing the device by an unqualified or unauthorized service technician may result in damage to the device and void the warranty.

CHILDREN AND PHYSICALLY OR MENTALLY DISABLED PEOPLE

• This device should not be operated by people (including children) with limited physical or mental abilities, as well as by people with no prior experience in the operation of electronic equipment.
• They may use the device only under supervision of people responsible for their safety. This device is not a toy. Memory cards are small enough to be swallowed by a child and cause choking. Keep the device and its accessories out of reach of children.

WATER AND OTHER LIQUIDS

• The device is IP69-rated. This means it is resistant to water and dust provided that all seals are intact and correctly fitted. Where possible, do not deliberately expose the device to water or other liquids.
• Water and other liquids are detrimental to the operation of electronic components. If the device gets wet, wipe it down and dry it as soon as possible.
• Before plugging the USB cable into the phone’s charging port, make sure it is dry. Plugging the cable into a wet port exposes it to gradual corrosion and may cause problems with charging the phone.

BATTERY AND ACCESSORIES

• Avoid exposing the battery to very high/low temperatures (below 0°C/32°F and above 40°C/104°F). Extreme temperatures may influence capacity and battery life.
• Avoid contact with liquids and metal objects, as it may cause partial or complete battery damage.
• The battery should be used according to its purpose. Do not destroy, impair, or throw the battery into flames – it might be dangerous and may cause fire. A worn-out or impaired battery should be placed in a dedicated container.
• Overcharging the battery can cause damage. Therefore, a single battery charge should not last longer than 3 days. Installing an incorrect battery type can cause an explosion. Never open the battery. Please dispose of the battery according to the instructions.
• Disconnect an unused charger from the power grid. In case of charger wire damage, it should not be repaired but replaced with a new one. Use the original manufacturer’s accessories only.

HEARING

• To avoid hearing damage, do not use the device at high volume levels for a long period of time; do not put the operating device directly to an ear.

EYESIGHT

• To avoid eyesight damage, do not look closely at the flashlight during its operation. A strong beam of light may cause permanent eye damage!

The use of the manual

The device and screenshots contained in this manual may differ from the actual product. Accessories attached to the set may differ from the illustrations included in the manual. Options described in the manual are found in the Android™ system. Those descriptions may differ, depending on the version of the operating system and applications installed on the device.

Important information

The majority of applications that can be installed on the device are mobile apps. The modus operandi of such applications may be different from their counterparts installed on a personal computer. Apps installed on the device may vary depending on country, region, and hardware specifications. The manufacturer is not liable for problems caused by third-party software. The manufacturer is not responsible for anomalies that may occur when editing the registry settings and modifying the operating system software. Attempts to modify the operating system can cause malfunctions and problems with applications. It may cause a loss of warranty.

Technical Specification

Model	Tablet WORKPAD LTE
Operating system	Android 16
Display	8.68” 1340×800 16,7K, IPS
Processor	Unisoc T7250 (ARM Mali-G57)
Rear camera (main)	16 Mpx
Front camera (selfie)	8 Mpx
RAM memory	8 GB + Virtual 8GB
Internal memory	128 GB
SIM	nano SIM + nano SIM + microSD
microSD	max. 2048 GB
Connectors	1 x USB-C, Pogo Pin docking port, 3.5 mm headphone jack
Connectivity	WiFi (2.4GHz+5GHz), Bluetooth 5.2, NFC, Galileo, BEIDOU, GLONASS,
2G	850, 900, 1800, 1900 MHz
3G	850, 900, 1700. 1900. 2100 MHz
4G	700, 800, 850, 900, 1700, 1800, 1900, 2100,2300, 2500, 2600 MHz
Battery	7100 mAh, Li-ion
Features	PowerBank, VoLTE, VoWiFi, Face recognition, Gravity sensor, Magnetometer, Light sensor, Proximity sensor, Accelerometer, Reverse charging
Water resistance	IP69 standard, MIL-STD-810H military certification
Dimensions	222 x 131.5 x 12.35 mm
Weight	540 g

• Technical specifications of the power supply used with the tablet.
• The power delivered by the charger must be between min 10 Watts required by the radio equipment and max 18 Watts in order to achieve the maximum charging speed.

Package content

• Tablet WORKPAD LTE
• USB cable
• Strap
• User manual
• If any of the above items is missing or damaged, please contact your dealer.
• We advise keeping the container in case of any complaints. Keep the container out of reach of children.
• Dispose of the container in accordance with local regulations when it is no longer needed.
• To help protect the environment, this pack does not include a charger. This device can be powered using most USB power adaptors and a cable with a USB Type-C plug.

Appearance of the tablet

Number	Funcitons
1	Brightness sensors
2	Digital camera lens: 8 Mpx (selfie)
3	SIM card and microSD slot
4	Blockade on/off button
5	Volume control buttons
6	Microphone
7	USB-C port
8	External speaker
9	Touchscreen
10	Slot Pogo Pin
11	Digital camera lens: 16 Mpx (main)
12	Flash light
13	SuperTorch
14	NFC
15	uSmart multifunction connector
16	Programmable button (Hammer Key)
17	3.5 mm headphone jack
18	Strap clip
19	Pressure relief vent! Do not insert any objects into it! Damage will invalidate the warranty!

Strap

A brief guide to the strap included in the set

1. Unclip the quick-release fasteners from both ends of the strap.
2. Thread the cord from the quick-release fastener through the loop in the pad. Then thread the quick-release fastener through the loop formed by the cord and pull firmly to secure it to the pad.
3. Snap both quick-release fasteners back into the ends of the strap.
4. Use the quick-release fasteners to fasten and unfasten the strap quickly.
5. Adjust the length of the strap using the buckle on the strap.

Before the first start

Mounting the SIM card(s) and memory card

1. Switch off the tablet before starting the installation.
2. The tray for the nanoSIM and microSD cards is located at the top of the casing, on the right-hand side.
3. Gently pry up and slide off the rubber cover protecting the slot.
4. Gently pry up the protruding tab on the tray with your fingernail.
5. Carefully pull the tray out of the tablet.
6. Place the nanoSIM card and/or microSD card into the appropriate slot on the tray. Position the card to match the shape of the embossed recess, paying attention to the position of the cut-off corner.
7. Carefully slide the tray back into the tablet, then gently press it down until it is fully seated.
8. Close the rubber cover securely, ensuring that it properly seals the slot.
   • Do not use excessive force when removing or inserting the SIM tray. Ensure that the nanoSIM card is correctly positioned before sliding the tray back into the tablet.
   • Use only memory cards recommended by the manufacturer. Pay attention to the selection of the proper format-the microSD card, capacity, and type/class. Incompatible memory cards may damage the device and cause the stored data to be destroyed as well. Incompatibility of memory card can be caused, among others, by an incorrect card format (required format microSD) or an unsupported card capacity – above the value recommended by the manufacturer.

Charging the battery

• Charge the battery before the first use. The battery should be charged by the attached charger or another charger intended for this type of equipment. If in doubt, contact the seller or manufacturer’s service. Use only chargers and wires recommended by the manufacturer. Using incompatible chargers or cables can cause an explosion of the battery or damage to your device. When the battery is near a complete discharge, the notification is displayed on a low battery charge. To continue using the device, charge the battery. If the battery is completely discharged, the device can not be switched on even when the charging process is ongoing. Before the device can be turned on again, the battery has to be charged for at least a few minutes.
• If there is a problem with the battery or if it needs to be replaced, the device should be delivered to the manufacturer’s service centre. To charge the battery, connect the USB-C plug to the socket in the device and the USB plug to the charger.
• Incorrect charger connection (USB cable) can cause damage to the AC adapter or the device. Damage resulting from improper handling is not covered by the warranty.
• Plug the charger into the wall socket. Once you start charging, an icon of the battery situated in the upper right corner will change to an animated symbol of lightning. If the device is turned off, an animation depicting the level of battery charge should appear.
• The device can heat up during charging. It is a regular occurrence and should not affect the stability or performance of the device.
• When the charge reaches 100%, it means that the battery is fully charged; finish charging. Unplug the charger from the wall socket and from the device.
• If the device does not charge properly, deliver it with the charger to a service center of the manufacturer.

Buttons

• Menu (virtual)
• Pressing it will cause the list of open apps to appear, where you can switch between them or turn them off.
• Home (virtual)
• One quick press takes you to the phone’s desktop. A longer press launches Google Assistant.
• Back (virtual)
• Press to exit the application / return to the previous screen.
• Blockade on/off button
• One quick press locks/unlocks the screen.
• Pressing the button for about 3 sec. will cause:
  • If the device is off – the device will switch on,
  • If the device is switched on – Calling up the Google Assistant – Gemini

Volume increase and decrease buttons

• Pressing during a voice call will cause an increase or decrease of the audio connection volume.
• Pressing while playing the incoming call sound mutes the ringer.
• Pressing the button when no calls are active will decrease or increase the volume of the ringtone, change sound profile on “vibration only” or “alarms only”.
• Pressing the button while the camera app is open might start the shutter and take a picture. (Works only if the software provides the function).
• Pressing the button in any other app will control the volume level of music, spoken instructions, or other sounds.

Turning on/off

• To switch the device on, press and hold (for about 3 seconds) on/off button.
• To turn off the device, with the home screen active, press the power button and the volume up button at the same time, and then select: [Power Off].

Using the touch screen

• A touch screen of the device lets you easily select items or perform operations.
• The touchscreen can be controlled by the following actions.

Touch

• Touch one to start options, app, menu

Swipe

• Quickly swipe up, down, to the left or to the right, to scroll the list or the screen.

Triple click

• Quickly tap the screen three times to start zooming – if this option is enabled in your device settings.

Hold and swipe

• Touch an element (an icon perhaps) and hold it for about 1 seconds. Then you can delete/uninstall that element.

Slide in and out

• Touch the screen with two fingers and slide them together or apart to zoom in or out a photo or a map.
• The touch screen will be turned off after some time of inactivity. To turn off the screen press the blockade button.
• In most tablets, you can set how long your device waits before turning off the screen. From the list of applications, it is usually sufficient to select [Settings] [Display] > [Screen Blanking].

eSIM Feature

• The tablet supports eSIM technology

Setting Up and Activating the eSIM

• An internet connection (Wi-Fi or cellular data) is required to install the eSIM profile.
• Next, go to [Settings] and select [Mobile Network/eSIM] from the menu list. Activating the eSIM involves downloading its profile by going through the setup process.
• If a SIM card is in the phone and already has an eSIM profile assigned by the carrier, the phone will automatically download and install that profile.
• To set up a new eSIM profile, enter the special QR code provided by your carrier. You can scan it using a QR code scanner or enter it manually by going to the [Need help?] tab while scanning.
• After scanning or entering the code, the SIM profile will download automatically. Once the profile is downloaded, a tab with the carrier’s name and the label “eSIM” will appear in [Menu] > [Settings] > [Cellular/eSIM], and a network coverage icon will appear in the top status bar.
• You can also view the process for setting up and activating an eSIM on the page linked below.

Disabling and Deleting a Profile

• To disable an eSIM profile, go to [Settings] > [Mobile Network/eSIM] > [eSIM Carrier Name], expand the advanced options, then in the [Carrier] tab, tap the settings icon and select Disable/Enable. Once the eSIM is disabled, the signal icon will disappear from the top bar.
• To completely delete the selected eSIM profile, select Delete.

Bluetooth

• A built-in Bluetooth module is a wireless, short-range communication technology used to exchange data up to 10 meters distance. The most commonly used Bluetooth devices are headphones or wireless speakers used to make voice calls and listening to music.
• Also car kits and other wireless mobile devices such as laptops, tablets, and mobile phones are often used.

Internet

• Select [Application menu] > [Settings] > [Network and Internet] > [Wi-Fi] and slide the slider to the right (turn it on). If you wish to add or give a new Wi-Fi network press the button and choose [Wi-Fi].
• Press the button or select the [View All] option. In this field you can see a list of available Wi-Fi networks, the connection status between the device and given network, an icon depicting network signal strength, security (a padlock visible).
• If a Wi-Fi network is secured then on an attempt to connect an enquiry for password will appear, which is to be entered by a virtual alphanumeric keyboard.
• If you do not have the Internet enable it in: [Applications menu] > [Settings] [Networks & Internet] > [Mobile network] [Data roaming] roaming of national calls or all calls.

Location

• There is a possibility to permit applications to use data and GPS satellites to determine the approximate location of the device. Also the possibility to allow Google to use location data in order to improve i.e. search results. Before using location services, such as map and navigation applications, or internet services, ensure that there is an active wireless connection to the Internet and the function of the GPS satellites in the [Application Menu]> [Settings]> [Location].

Maintenance of the device

• To prolong the life span of the device act according to these instructions.
• Keep the device and its accessories out of reach of children.
• Avoid contact with liquids; it can cause damage to electronic components of the device.
• Avoid very high temperatures for it can shorten the life of device electronic components, melt the plastic parts and destroy the battery.
• Do not try to disassemble the device. Tampering with the device in an unprofessional manner may cause serious damage to the device or destroy it completely.
• For cleaning use only a dry cloth. Never use any agent with a high concentration of acids or alkalis.
• Use only the original accessories. Violation of this rule may result in an invalidation of the warranty.
• The packaging of the device can be recycled in accordance with local regulations.

The use of the manual

Consents

• Without prior written consent of the manufacturer, no part of this manual may be photocopied, reproduced, translated, or transmitted in any form or by any means, electronic or mechanical, including photocopying, recording or storing in any systems of storing and sharing information.

Appearance

• The device and screen shots contained in this manual may differ from the actual product. Accessories attached to the set may differ from the illustrations included in manual.

Trademarks

• Google, Android, Google Play, Chrome and other marks are trademarks of Google LLC.
• Oracle and Java are a registered trademarks of Oracle and / or its affiliates.
• Wi-Fi® Wi-Fi logo are a registered trademarks Wi-Fi Alliance association.
• All other trademarks and copyrights belong to their respective owners.

Correct disposal of used equipment

The device is marked with a crossed-out garbage bin, in accordance with the European Directive 2012/19/EU on used electrical and electronic Equipment (Waste Electrical and Electronic equipment – WEEE). Products marked with this symbol should not be disposed of or dumped with other household waste after a period of use. The user is obliged to get rid of used electrical and electronic equipment by delivering it to designated recycling point in which dangerous waste are being recycled. Collecting this type of waste in designated locations, and the actual process of their recovery contribute to the protection of natural resources. Proper disposal of used electrical and electronic equipment is beneficial to human health and environment. To obtain information on where and how to dispose of used electrical and electronic equipment in an environmentally friendly manner, user should contact their local government office, the waste collection point, or point of sale, where the equipment was purchased.

Correct disposal of used battery

According to the EU directive 2006/66/EC with changes contained in EU directive 2013/56/UE on the disposal of batteries, this product is marked with crossed-out garbage bin symbol. The symbol indicates that the batteries used in this product should not be disposed with regular household waste, but treated according to the legal directives and local regulations. It is not allowed to dispose of accumulators with unsorted municipal waste. Users of batteries and accumulators must use the available collection points of these items, which allows them to return, recycle and disposal. Within the EU, the collection and recycling of batteries and accumulators is a subject to separate procedures. To learn more about existing procedures of recycling of batteries and accumulators please contact your local office or an institution for waste disposal or landfill.

Specific absorption rate SAR

• SAR is a value indicating the amount of radiation emitted by the device. The SAR limit recommended by the Council of the European Union is 2 W/kg.

Declaration of conformity with European Union Directives

• mPTech Ltd. hereby declares that the techBite WORKPAD LTE tablet is compliant with Directive 2014/53/EU.
• The full text of the EU Declaration of Conformity is available at the following Internet address: https://hammerphones.com/wsparcie-dla-hammer-workpad-lte

CUSTOMER SERVICE

• We create for you.
• Thank you for choosing the techBite device. This product has been designed especially for you. We are doing everything to make its use pleasurable and comfortable.
• We made sure that elegance, functionality, and convenience of use were combined with an affordable price. For your own safety, please read this manual carefully.
• Manufacturer:
  • mPTech Ltd.
  • Nowogrodzka 31 Street
  • 00-511 Warsaw
• Poland
  • Helpline: (+48 71) 71 77 400
  • E-mail: pomoc@mptech.eu
  • Equipment delivery location:
  • mPTech Ltd.
  • Krakowska Street 119
  • 50-428 Wrocław
• Poland
  • Website: www.mptech.eu
  • Manufactured in China

User manual

• The actual product, accompanying accessories, and some of its features may differ from the images and descriptions presented in this manual.
• The latest manual is available on the product website: https://hammerphones.com/wsparcie-dla-hammer-workpad-lte
• To open this page, simply scan this QR Code

Troubleshooting

• Device won’t charge properly: If the device does not charge properly, deliver it (with the charger) to the manufacturer’s service center.
• Tablet can’t be powered on after full discharge: if the battery is completely discharged, the device cannot be switched on even while charging is ongoing—charge the battery for at least a few minutes before turning it on again.
• SIM tray issues: avoid using excessive force when removing/inserting the SIM tray; ensure the nanoSIM card is correctly positioned before sliding the tray back in.
• Using incompatible memory cards: use only memory cards recommended by the manufacturer; incompatible cards may damage the device and destroy stored data.
• Screen not responding/turned off: the touchscreen turns off after inactivity; press the blockade button to turn the screen off/on as described in the manual.
• Device got wet: wipe it down and dry it as soon as possible; the device is IP69-rated only if seals are intact and correctly fitted.
• Incorrect charger/cable connection: an incorrect charger connection (USB cable) can damage the AC adapter or the device; damage from improper handling is not covered by warranty.