BT7 Solar Backup Camera System
“
Product Specifications:
- Monitor:
- LCD size: 7 inches / 5.5 inches
- Resolution: 1024×600 / 1280×720
- Brightness: Max. 6W / Max. 4.5W
- Power Consumption: 800:1
- Contrast: U/D:85, R/L:85
- Viewing Angle: 16:9
- Aspect Ratio: 4 channels
- Operating Frequency: 2400-2483 MHZ
- Receiving Sensitivity: -85 dBm
- Video Compression: H.264
- Latency: 120ms
- Transmitting Distance: 984ft line of sight
- Micro-SD / TF Card: Max. 256G
- Video Format: AVI
- Power Supply: DC10-32V or USB Type-C 5V
- Loudspeaker: 1W/8
- Operating temperature
- Storage temperature
- Camera:
- PAIR button
- Light Sensor
- Micro SD Card Slot
- Power button
- USB Type-C DC
- Power Indicator: Red when powered on, Green when working
normally
- Accessories:
- Solar Panel
- 3M Mount Bracket
- Suction Cup Mount Bracket
- Camera Charging Conversion Cable
- Solar Panel Extension Cord
- Cigarette Lighter
- Type-C Cable
- Metal Plate with 3M Tape for Camera
- Metal Plate with 3M Tape for Solar Panel
- Power Adapter
Product Usage Instructions:
Powering the Device:
The device can be powered by DC 10-32V or USB Type-C 5V/2A.
Ensure proper cable connections to avoid damage to the monitor.
Remove the power cable connections when not in use.
Monitor Installation:
Adjust monitor height by sliding it up or down in the slot and
tighten the knob. Adjust the angle by loosening the lower knob on
the suction cup mount, tilting the monitor to the desired angle,
and then re-tighten the knob.
Battery-Operated Camera and Solar Panel:
Power Button Functions:
- Short Press: Turn ON/OFF the entire camera in
non-charging status. In charging status, turn ON/OFF the camera
itself. - Press for 5 Seconds: Enters remote control
pairing mode (remote control needs to be purchased
additionally). - Press for 20 Seconds: Enters deep sleep mode.
Short press again to awaken the camera.
Multi-Angle Adjustment Display Mount:
This mount allows for versatile adjustment options for your
display.
Frequently Asked Questions (FAQ):
Q: What power sources can be used for the device?
A: The device can be powered by DC 10-32V or USB Type-C
5V/2A.
Q: How do I adjust the monitor angle?
A: Loosen the lower knob on the suction cup mount, tilt the
monitor to the desired angle, and then re-tighten the knob.
A: The power button on the camera can be used to turn ON/OFF the
camera and enter different modes based on the duration of
pressing.
“`
2.4G Digital 1080P Touch Screen System
User Manual
CH4
120s 240s NEVER ON
REC
CH1
CH2
CH3
CH4
QMODE
Byte Tango System
BT7 Solar / BT6 Solar
The antennas of BT6 Solar is shorter than BT7 Solar, please refer to the actual product received.
1. The device can be powered by DC 10-32V or USB Type-C 5V/2A. 2. Improper cable connections may damage the monitor. Remove the power cable connections
when you do not intend to use the device.
1
2
FCC WARNING
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: — Reorient or relocate the receiving antenna. — Increase the separation between the equipment and receiver. — Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. — Consult the dealer or an experienced radio/TV technician for help. To maintain compliance with FCC’s RF Exposure guidelines, This equipment should be installed and operated with minimum distance between 20cm the radiator your body: Use only the supplied antenna.
3
7″ or 5.5″ Monitor
BTC140 Camera
Solar Panel
3M Mount Bracket
Suction Cup Mount Bracket
Camera Charging Conversion Cable
Solar Panel Extension Cord
Cigarette Lighter
Type-C Cable
Metal Plate with 3M Tape for Camera
Metal Plate with 3M Tape for Solar Panel
Power Adapter
The product is under continuous improvement and the specifications will change without notice. Picture for reference only. Please refer to the actual product and accessories.
The antennas of BT6 solar is shorter than BT7 solar, please refer to the actual product received.
4
Upgraded touch screen for easy operation. NORMAL, MIRROR, FLIP and MIR-FLIP viewing available. Split mode auto-scan mode and single-display mode available. Support 4-channel composite and single-channel recording in AVl signal format. Auto dim function available. 4 wireless camera inputs. Video input:1080P. Wide voltage input: DC10-32V or USB Type-C 5V. Camera night LED can be turned ON/OFF via monitor. The monitor turns on and the camera wakes up automatically. The camera turns off automatically one minute after the monitor turns off.
Monitor
LCD size Resolution Brightness Power Consumption Contrast Viewing Angle Aspect Ratio Channel Operating Frequency Receiving Sensitivity Video Compression Latency Transmitting Distance Micro-SD /TF Card Video Format Power Supply Loudspeaker Operating temperature Storage temperature
7″ 16:9
5.5″ 16:9
1024×600
1280×720
1000 cd/m²
550 cd/m²
Max.6W
Max.4.5W
800:1
U/D:85,R/L:85
16:9
4 channels
2400-2483 MHZ
-85 dBm
H.264
120ms
984ft line of sight
Max.256G
AVI
DC10-32V or USB Type-C 5V
1W/8
-20~+70°C, RH90%
-30~+80°C, RH90%
5
Camera
lmage Device TV System Effective Pixels Pixel Size Video Output Scanning System Sync.System Gamma Consumption AGC White Balance BLC Electronic Shutter Operation Frequency Transmission Distance (barrier free) Transmission Power Video Code Spread Spectrum Latency RF Bit Rate Minimum lllumination Power supply Night Vision Distance Viewing Angle Audio Battery Capacity Charging Voltage Charging Time Discharging Time Mounting Connection Waterproof Rating Charging Temperature Discharging Temperature Storage Temperature
1/2.9″CMOS 25 f/s 30 f/s 1920×1080 pixels 2.8umx2.8um 8bits YUV Progressive Scanning Internal 0.45 Auto Auto Auto Electronic Rolling Shutter 2400-2483MHz 300m(984ft) 18dBm H.264 DSSS 120ms 12Mbps 0Lux DC5-16V 8~10m(26~32ft) 120° Yes 37Wh DC: 5~16V 5.5H@12V 14H Magnetic mount Camera Charging Conversion Cable IP67 -10~45°C -10~60°C -20~60°C
6
PAIR button Light Sensor Micro SD Card Slot
Power button USB Type-C DC
Power Indicator It turns to red when the monitor is powered on. Indicator is green when the monitor is working normally.
7
Speaker
Installation of Suction Cup Mount: 1. Adjust monitor height by sliding monitor up or down in slot, then tighten knob.
Adjust monitor angle by loosening lower knob on suction cup mount, tilting monitor to desired angle and re-tighten knob.
2. Installation of 3M Mount
8
This multi-purpose multi-angle adjustment display mount can be used like below
9
7 Battery-Operated Camera and Solar Panel
Power Button
Power Button
Short Press Power Button
In non-charging status, turn ON/OFF the entire camera (camera itself and battery)
In charging status, turn ON/OFF the camera itself (the battery will continue charging or discharging)
Press Power Button for 5 Seconds
Pressing power button for 5 seconds when device power on, two indicator lights blinking at the same time, entering remote control pairing mode (the remote control needs to be purchased additionally).
Press Power Button for 20 Seconds
When device power on, pressing power button for 20 seconds until all indicator lights off, the device will enter deep sleep mode. Short press power button again to awaken the camera.
Pairing
Two methods for pairing
Method 1: Press the pair button on the monitor first
, and then press the pair button on the
camera(The camera is turned on). After successful pairing, the monitor will display the image
captured by the camera.
Note: To realize the remote power on/off, the camera must be paired on the channel of CAM4.
PAIR button
Indicators
10
Method 2: Press the pair button on the monitor first , and then press the power button on the camera(The camera is turned off). After successful pairing, the monitor will display the image captured by the camera. Note: To realize the remote power on/off, the camera must be paired on the channel of CAM4.
Automatic Standby
Unplug the charger when charging, the camera will automatically enter standby mode after 5 minutes. Under normal working condition, turn off the monitor or the camera has signal loss for over 1 minute, the camera will automatically enter standby mode.
Indicators
Indicators OFF
The standby current of the camera after manually entering the deep sleep state is 60uA, and the camera can be stored for a long time while the battery is fully charged. Note: If you need to store the camera for a long time, please disconnect the solar panel, otherwise the solar panel will automatically recharge under certain conditions, prompting the camera to exit the deep sleep state.
Short press the camera power button to enter standby mode, or turn off the camera remotely by monitor, the camera can be woken up by the monitor at any time. If the battery is fully charged, the camera can be placed for 8 months.
Red Indicator ON
Reverse positive and negative polarity.
1st Indicator ON and 4th Indicator Blinking
The battery temperature is greater than 65°C/149°F. The camera
will stop charging and working. The camera will resume charging and working automatically when the battery temperature return to normal. Note: If the temperature is often too high, please keep the product away from heat sources.
Second and Third Indicators Blinking
Second Indicator Blinking and 4th Indicator ON
Load short-circuit
Charging voltage is higher than 16V (every 10 seconds the second indicator flashes and 4th indicator lights up for 2 seconds).
11
Charging and Discharging
Charging by DC Adaptor
Supports DC 5-16V, battery can be fully charged in 5.5 hours with DC 12V.
The 9V 8W solar panel can fully charge the camera battery in Charging by Solar Panel 48 hours when there is enough light and the camera is not working.
Discharging when Solar The camera can work for 14 hours with a fully charged battery
Panel Disconnected
(at 25°C/77°F with night light turned off).
Discharging when Solar If the camera works for 4 hours a day, the solar panel can keep the
Panel Connected
camera working continuously (abundant sunlight and 25°C/77°F).
8 CCaammeerraaaWndiriSnoglaMrePthaondel: Wiring Method:
Magnet
Magnet
Note: Make sure the magnet part is attached to the metal plate
12
Monitor Wiring:
Connect the monitor to the cigarette lighter power adapter. Power the monitor through the vehicle’s 12V cigarette lighter or USB Type-C.
18
9
Solar Panel Extension Cord If the solar panel is mounted close to the camera, it can be used without connecting the solar panel extension cord.
13
19
CH1
CH1
2
2 Image freezing may occur when the vehicle is 42-65ft long and the antenna is mounted in a poor location (the antenna is not placed on the roof of the vehicle or there is obstruction around the antenna). In this case, it is recommended to purchase the Haloview 10M or 12M antenna extension cable and place it on the roof without any obstacles.
14
It is recommended to choose an antenna length that is 2-3ft longer than the length of the RV.
To achieve better signal, it is recommended to purchase the Haloview antenna extension cable and place it in front of the RV where near the roof without any obstacles.
CH1
If you get poor signal reception, or signal cannot reach at least 2 bars,
please keep the antennas perpendicular and adjust the angle of
antenna to find best signal reception position.
10
Shortcut Menu
Tap the screen when in single image mode, it pops-up the first group of shortcut MENU. You can easily switch to each of the four channels of cameras or go to Quad Mode. Tap to go to Main MENU.
CH4
120s 240s
NEVER ON
REC
CH1 CH2 CH3 CH4 QMODE
15
The camera with solar panel must be paired in the CH4. After successful pairing, you can see the UI shown as below in the CH4 channel.
CH4
120s 240s
NEVER ON
REC
CH1 CH2 CH3 CH4 QMODE
120S: The camera automatically wake up when the monitor is turned on, and the camera will be automatically turned off after 120 seconds.
240S: The camera automatically wake up when the monitor is turned on, and the camera will be automatically turned off after 240 seconds.
NEVER: The camera automatically wake up when the monitor is turned on. The camera will continue to work and won’t be turned off automatically. If NEVER is selected, the camera won’t be turned off even when switching from CH4 to other CH. To turn off camera in CH4, please tap OFF.
ON/OFF: Tap ON/OFF to easily turn ON/OFF the camera manually.
Notice: Even if NEVER is selected, turn off the monitor or the monitor lose signal with the
camera for over 1 minute, the camera will automatically turn off.
Tap the screen again, it pops-up the second group of shortcut MENU.
CH4
120s 240s
NEVER ON
REC SCAN
16
Tap to turn on/off parking line in current channel of camera. When parking line is turned on, exit the shortcut menu to display the parking line.
Tap to turn on/off voice in current channel of camera.
Tap to adjust the screen brightness. Tap to turn on/off current camera night light. When camera night light is turned on, the indicator will turns from to .
Tap to start recording or pause recording. Tap SCAN to automatically switch channels of cameras.
In quad mode (QMODE), an audio icon highlighted in CH1 that has the audio active.
CH1
REC CH2
CH3
CH4
Tap any of the audio icon to hear the audio of any channels of cameras.
CH1
REC CH2
CH3
CH4
17
The audio icon is highlighted to indicate that audio is turned on for that channel.
CH1
REC CH2
CH3
CH4
Notice: Please tap the audio icon instead of other areas. Otherwise the display will switch to the certain channel of camera.
Press
to go to Main Menu
CH1
REC
SCAN
Press
to exit.
10.1 MENU
CH1
REC
SCAN
18
10.2 VOLUME
CH1
REC
9
MUTE
OFF
Tap
to get access to VOLUNE setting
Tap the bar to adjust volume. Tap ON/OFF to MUTE or UNMUTE the volume.
10.3 PAIRING
PAIR button
Camera and monitor are paired at the channel of CAM4 as factory default setting. When you open the box, power on the monitor and camera, tap the monitor to find the first group of shortcut Menu and tap CH4, the image will be displayed. Otherwise, please try below methods for pairing.
Tap
to get access to Main Menu. Tap
to enter pairing status, you will
have 50 seconds for pairing. Press the pairing button on the bottom of the camera
until you hear a “tah”. Video will be displayed after pairing complete.
CH1
REC
Please Press Pair key on Camera or Transmitter Box
50
19
Quick Access to Pairing Status: Press the PAIR button for 3 seconds to enter pairing status.
PAIR button
If you press the pair button by mistake and the monitor enters the pairing status, you can tap to exit the pairing status.
CH1
REC
Please Press Pair key on Camera or Transmitter Box
50
10.4 PICTURE
CH1
REC
9 9 9
ON
Tap
to get access to Main Menu. Tap
to enter Picture setting.
Tap the bars to the adjust BRIGHTNESS/CONTRAST/COLOR.
Tap ON/OFF to turn on/off the current camera night led light.
20
10.5 MIRROR
CH1
REC
Tap
to get access to Main Menu. Tap
Tap Normal/Mirror/Mir-flip/Flip at your will.
10.6 QMODE
to enter MIRROR setting.
CH1
REC
13
SPLIT-1/3
14
SPLIT-1/4
23
SPLIT-2/3
24
SPLIT-2/4
34
SPLIT-3/4
4 12
TRIPLE 1
4 13
TRIPLE 2
4 23
TRIPLE 3
12 4
TRIPLE 4
13 4
TRIPLE 5
23 4
TRIPLE 6
4 21
TRIPLE 7
3 12
TRIPLE 8
3 21
TRIPLE 9
12 34
QUAD 1
1
3 4
2
QUAD 2
2
3 4
1
QUAD 3
Tap
to get access to Main Menu. Tap
Tap any of desired display mode.
10.7 SETTING
to enter QMODE setting.
CH1
REC
CAM
TRIGGER
COLOR-SYS
ON NTSC
AUTODIM
ON
SCREEN OFF
0
21
Tap
to get access to Main Menu. Tap
Tap ON/OFF to turn on/off Trigger.
Tap NTSC/PAL to switch video format.
to enter.
Tap ON/OFF to turn on/off Autodim. When Autodim is turned on, monitor will automatically decrease brightness in low light. Tap the bar from 0 to 45 to set screen off duration. If 0 is selected, the screen stays on. If 45 is selected, the display will turn off after 45 seconds of inactivity.
10.8 SCAN
CH1 ON ON
CH3
REC
ON
CH2
ON
CH4 45
Tap
to get access to Main Menu. Tap SCAN to enter SCAN setting.
The SCAN function allows the monitor to automatically switch channels of cameras.
In the shortcut menu, you can tap
to start Scan or exit Scan. A Scan icon will
appear on the display if the display enters scan mode.
22
10.9 Park Line Adjustment
CH1
REC
Tap
to get access to Main Menu. Tap to enter parking line setting.
You can slide the screen to adjust the inclination and the width of the parking line.
CH1
REC
Slide left/right to adjust park lines horizontally
CH1
REC
Slide up/down to adjust park lines vertically
23
10.10 RECORD
CH1
REC. RECORD FORMAT
COVER
TIME
REC
ON OFF
ON
2023/12/03 00:00:00
Tap
to get access to Main Menu. Tap to enter RECORD setting.
Please insert TF card in TF card slot, max 256G Micro SD card.
Note: TF card must be formatted before using. Tap Format ON and Confirm Format.
After TF card is formatted, a yellow folder icon will be shown on the screen,
indicating TF card is available now.
When COVER is turned on, overwrite function will be activated. Previously recorded video files will be overwritten when TF card memory is full. Note: When in QUAD or SPLIT display, the monitor will record all displayed channel of CAM at the same time.
24
TIME Setting:
CH1
REC. RECORD FORMAT
COVER
TIME
REC
ON OFF
ON
2023/12/03 00:00:00
Tap Year/Month/Date/Hour/Minute/Second, it will pops-up and , tap and to adjust Year/Month/Date/Hour/Minute/Second.
10.11 PLAY
Free : 20.69G Total : 29.73G
DCIM
FOLDER
Tap
to get access to Main Menu. Tap to enter PLAY setting.
Tap
to select, Tap and to move up or down.
Tap
to play the selected file.
Read the SD card through PC, there will be two formats of files. It is suggested to play the AVI format file for higher video resolution.
25
10.12 Trigger Function
Tap
to get access to . The Trigger switch off by default.
CH1
REC
CAM
TRIGGER
COLOR-SYS
ON NTSC
AUTODIM
ON
SCREEN OFF
0
Tap ON to activate Trigger function. If trigger switch is turned on, the yellow icon will appear on display. To achieve trigger function, you also need to complete trigger wiring.
In Triggering status, MENU operation invalid, and the screen prompts TRIGGER LOCK.
CH1
REC
26
19 19
Touch screen invalid
For example, if you connect the camera to left turn signal light, the camera will automatically displayed on the monitor every time the left turn signal light turned on. Touch screen invalid during triggering. Once triggering released, touch screen be operational again.
27
Documents / Resources
![]() | Haloview BT7 Solar Backup Camera System [pdf] User Manual BT7 Solar Backup Camera System, BT7 Solar, Backup Camera System, Camera System, System |