Studio Technologies 545DC Jagorar Mai Amfani da Intercom Intercom

Wannan Jagorar Mai Amfani yana aiki don jerin lambobin M545DC-00151 kuma daga baya tare da Aikace-aikacen Firmware 1.00 kuma daga baya da sigar aikace-aikacen mai sarrafa ST 3.08.00 da kuma daga baya.

Tarihin Bita

Magana ta 2, Fabrairu 2024:

• Ana ɗaukaka Model 545DC hoto na baya.

Fitowa ta 1, Yuni 2022:

• Sakin farko.

Gabatarwa

Model 545DC Intercom Intercom yana ba da damar da'irori guda biyu na analog-line party-line (PL) da na'urorin masu amfani masu alaƙa don haɗa su cikin aikace-aikacen Dante® audio-over-Ethernet.
Ana amfani da tsarin intercom na analog-line party-line (PL) guda ɗaya a cikin gidan wasan kwaikwayo, nishaɗi, da aikace-aikacen ilimi inda ake son mafita mai sauƙi, abin dogaro, mai rahusa, da sauƙin amfani. Dante ya zama babbar hanyar haɗa siginar sauti da na'urori daban-daban ta amfani da daidaitattun hanyoyin sadarwa na Ethernet. Model 545DC kai tsaye yana goyan bayan layin jam'iyyar analog (PL) da Dante, yana ba da kyakkyawan aiki a cikin yankuna biyu. Samfuran layin jam'iyyar analog guda ɗaya tashoshi (PL) daga Clear-Com® sun dace kai tsaye tare da Model 545DC. Ana amfani da fasahar sadarwar watsa labarai ta Dante audio-over-Ethernet don jigilar aikawa da karɓar tashoshi na sauti masu alaƙa da da'irori guda biyu na layi na jam'iyyar (PL). Model 545DC's biyu matasan da'irori tare da atomatik nulling mataki samar da mai kyau rabuwa da aika da karɓar audio tare da babban koma baya da kuma m audio ingancin. (Wadannan wuraren da'irar da aka yi suna wasu lokuta ana kiransu 2-waya zuwa masu sauya waya 4.)
Siginonin sauti na dijital na Model 545DC sun dace da duk kayan aikin da ke amfani da fasahar Dante.
Haɗin Ethernet shine duk abin da ake buƙata don yin Model 545DC ɓangaren nagartaccen tsarin sauti na hanyar sadarwa.

Model 545DC na iya haɗa haɗin gwiwa tare da na'urori masu goyan bayan Dante kamar tsarin matrix intercom,
dijital audio processor, da audio consoles. Naúrar ta dace kai tsaye tare da RTS ADAM® da tsarin ODIN® intercom waɗanda ke goyan bayan fasahar cibiyar sadarwa ta OMNEO®. A madadin, nau'ikan Model 545DC guda biyu ana iya haɗa su ta hanyar hanyar sadarwar Ethernet mai alaƙa. Model 545DC kuma na iya zama wani ɓangare na tsarin layi na jam'iyya (PL) idan aka yi amfani da shi tare da na'urori kamar Model 5421 da 5422A Dante Intercom Audio Engine raka'a daga Studio Technologies. Ta wannan hanyar, layin jam'iyyar analog (PL) na intercom na iya zama wani ɓangare na babban aiki na layin jam'iyyar dijital (PL).

Model 545DC na iya samun ƙarfi ta Power-overEthernet (PoE) ko tushen waje na 12 volts DC. Ƙungiyar za ta iya samar da tushen wutar lantarki guda biyu-line (PL) da kuma hanyoyin sadarwa na dakatar da impedance analog, suna ba da damar haɗin kai tsaye na belpacks mai amfani kamar na'urorin Clear-Com RS-501 da RS-701. Model 545DC kuma na iya haɗawa zuwa ɗaya ko biyu da ake da ƙarfi da kuma ƙarewar layin jam'iyyar analog ta hanyar sadarwa ɗaya (PL). Ƙungiyar tana ba da mita matakan sauti guda huɗu waɗanda ke taimakawa don tabbatar da aikin tsarin yayin saiti da aiki. An kuma bayar da goyan baya don jigilar siginonin haske na daidaitattun masana'antu tsakanin Model 545DC raka'a biyu, da kuma tsakanin Model 545DC da sauran raka'o'in da suka dace.

Hoto 1. Model 545DC Intercom Intercom Interface gaba da baya views

Ana iya amfani da aikace-aikacen software mai sarrafa ST don saka idanu na gaske da sarrafa sigogin aiki na Model 545DC da yawa. Bugu da kari, ana yin saitunan daidaitawa guda biyu ta amfani da aikace-aikacen. Akwai nau'ikan masu sarrafa ST waɗanda suka dace da tsarin aiki na Windows® da mac OS®. Ana samun su, kyauta, daga Studio Technologies' website.

Ana amfani da daidaitattun masu haɗawa don Model 545DC party-line (PL) intercom, Ethernet, da haɗin wutar lantarki na DC. Saita da daidaitawar Model 545DC abu ne mai sauƙi. Ana amfani da jack ɗin Neutrik® etherCON RJ45 don haɗa haɗin kai tare da daidaitaccen tashar tashar Ethernet mai murɗaɗi mai alaƙa da cibiyar sadarwar yanki (LAN). Wannan haɗin yana iya samar da ƙarfin PoE duka da sautin dijital na bidirectional. LEDs suna ba da alamun matsayi na haɗin Ethernet da Dante.

Yakin aluminium mara nauyi na naúrar an yi niyya ne don amfani da tebur ko saman tebur. Na'urorin hawan zaɓi na zaɓi suna ba da damar ɗaga raka'a 545DC Model ɗaya ko biyu a cikin sarari ɗaya (1U) na daidaitaccen shinge na inch 19.

Aikace-aikace

Akwai manyan hanyoyi guda uku da Model 545DC za a iya amfani da a aikace-aikace: haɗa analog party-line (PL) intercom da'irori zuwa Dante tushen intercom aikace-aikace, ƙara jam'iyyar-line (PL) intercom goyon bayan matrix intercom tsarin, da kuma haɗa biyu standalone analog. jam'iyyar-line intercom circuits. Model 545DC's Dante transmitter (fitarwa) da tashoshi mai karɓa (shigarwar) za a iya haɗa su zuwa da'irori na PL na dijital na tushen Dante. Za a ƙirƙiri waɗannan da'irori galibi ta amfani da na'urori irin su Studio Technologies' Models 5421 ko 5422A Dante Intercom Audio Engines. Wannan zai ba da damar gadon kayan aikin intercom na partyline na analog ya zama wani ɓangare na aikace-aikacen intercom na dijital na zamani. Sakamakon ingancin sauti na duka analog da Dante-base PL yakamata ya zama kyakkyawa.

Tashoshi a kan tsarin intercom na matrix wanda ke goyan bayan Dante, kamar RTS ADAM da ODIN tare da OMNEO, ana iya tura su zuwa Model 545DC na Dante transmitter (fitarwa) da tashoshi mai karɓa (shigarwa). Model 545DC's circuitry sannan zai canza waɗannan sigina zuwa da'irori guda biyu na analog-line intercom da'irori. Ta wannan hanyar, ƙara tallafin layin jam'iyyar analog zai zama aiki mai sauƙi. Hakanan za'a iya amfani da Model 545DC tare da tsarin matrix intercom waɗanda basa goyan bayan Dante. Ana iya amfani da ƙa'idar analog-zuwa-Dante ta waje don canza albarkatun intercom na analog "4-waya" zuwa tashoshin Dante. Don misaliampHar ila yau, Model 544D Audio Interface daga Studio Technologies ya dace da aiki tare da tsarin intercom na matrix. Sau ɗaya a cikin yankin dijital na Dante, waɗannan tashoshi masu jiwuwa ana iya haɗa su tare da Model 545DC na Dante mai karɓar (shigarwa) da tashoshin watsawa (fitarwa).

Za'a iya haɗa keɓaɓɓun keɓaɓɓun layin analog-line party-line (PL) cikin sauƙin haɗin kai ta amfani da Model 545DC Model guda biyu. A kowane ƙarshen, an haɗa Model 545DC zuwa guda ɗaya ko biyu na PL da kuma hanyar sadarwar Dante. Ana amfani da aikace-aikacen software na Dante Controller don hanya (biyan kuɗi) tashoshi mai jiwuwa tsakanin sassan Model 545DC guda biyu. (Tazarar jiki tsakanin raka'a za a iyakance shi kawai ta hanyar tura LAN ta subnet.) Shi ke nan - babu wani abu da ake buƙata don cimma kyakkyawan aiki.

Hakanan za'a iya amfani da Model 545DC don "gada" (haɗin kai) ɗaya ko biyu tashoshi ɗaya ko biyu tare da da'irar layi na layi na jam'iyya mai lamba 2. Wannan ya haɗa da amfani da Model 545DC don tallafawa da'irar tashoshi guda ɗaya da Fa'idar Fasahar Fasaha ta Model 545DR Intercom Intercom don tallafawa da'irar layin jam'iyya-2-channel. Model 545DR shine "dan uwan" na Model 545DC kuma yana goyan bayan da'irar intercom-line jam'iyyar tashoshi 2 maimakon da'irori guda biyu na singe-tashar. Wannan da'irar tashoshi 2, yawanci ana goyan bayan kayan aiki daga RTS, ana amfani da su a aikace-aikacen watsa shirye-shirye.

Interface Interface

Kamar yadda aka tattauna a baya, Model 545DC's ƙungiyoyi biyu-line intercom musaya an inganta su don haɗi tare da da'irori guda biyu na jam'iyyar-layi na intercom ko ƙungiyoyi na na'urorin masu amfani da tashoshi ɗaya. (Yayin da Model 545DC kuma zai yi aiki a cikin iyakataccen hanya tare da 2-tashar RTS TW da'irori, Model 545DR Intercom Interface shine zaɓin da aka fi so. Ba za a haɗa da'irar intercom na layi ba Model 545DC's interface circuitry zai kasance barga. Wannan keɓantaccen fasalin yana tabbatar da cewa siginonin odiyo masu ƙin yarda, gami da girgizawa da “kumburi,” ba za a aika zuwa wasu na'urori masu kunna Dante ba.

Muhimmiyar iyawar Model 545DC's musaya-layi na jam'iyya guda biyu shine ikonsu na samar da wuta da ƙarewar AC 200 ohms don "ƙirƙira" da'irori masu zaman kansu guda biyu. Kowace fitowar DC 28 volts na iya kunna matsakaicin adadin na'urori kamar fakitin bel na mai amfani. Tare da har zuwa milliliters 150 (mA) na yanzu da ake samu, aikace-aikacen nishaɗi na yau da kullun na iya haɗawa har zuwa fakitin RS-501 ko RS-701 guda biyar zuwa kowane ɗayan Model 545DC biyu. A cikin aikace-aikace da yawa, wannan na iya kawar da buƙatar samar da wutar lantarki ta intercom na waje, rage jimlar farashin tsarin, nauyi, da sararin hawa da ake buƙata. Ana kula da abubuwan samar da wutar lantarki don wuce gona da iri da yanayin gajere. Ƙarƙashin firmware (software mai haɗawa) sarrafa abubuwan da aka fitar za su sake zagayowar ta atomatik kuma a kunna don taimakawa hana lalacewa ga kewayawa da kayan aikin da aka haɗa.

Dante Audio-over-Ethernet

Ana aika bayanan sauti zuwa kuma daga Model 545DC ta amfani da fasahar sadarwar Dante audio-over-Ethernet. Sigina na sauti tare da asampana tallafawa ƙimar 48 kHz da ɗan zurfin har zuwa 24.
Mai watsa sauti (fitarwa) da tashoshi masu karɓa (shigarwa) akan na'urorin da aka kunna Dante masu alaƙa za a iya tura su zuwa Model 545DC ta amfani da aikace-aikacen Dante Controller. Wannan ya sauƙaƙa don zaɓar hanyar da Model 545DC ya dace da takamaiman aikace-aikacen.

Analog Hybrids tare da Lulling Auto

Da'irori biyu, waɗanda ake magana da su a matsayin “hybrids,” suna yin mu'amala da mai watsa Dante (fitarwa) da tashoshi mai karɓa (shigarwar) tare da tashoshi biyu na layin jam'iyya. Matakan suna ba da ƙaramar amo da murdiya, kyakkyawar amsawar mita, da babban hasara mai yawa ("nulling"), ko da lokacin da aka gabatar da shi tare da yanayin layi na jam'iyya. Ba kamar layin tarho ("POTS") da'irori na tushen DSP na tushen da'irori ba, ƙirar 545DC's kwatankwacin kewayawa yana kiyaye tsawaita amsawar mitar. Tare da band ɗin wucewa na 100 Hz akan ƙaramin ƙarshen da 8 kHz akan babban ƙarshen, ana iya aika siginar murya mai sautin yanayi zuwa kuma karɓa daga da'irar layin jam'iyya.

Model 545DC's sophisticated hybrid auto bulling function yana amfani da haɗe-haɗe na dijital da kwatancen kewayawa a ƙarƙashin sarrafa microprocessor don cimma gagarumin asarar trans-hybrid. Ana samun wannan “rasa” asarar dawowa ta hanyar yin jerin gyare-gyare na firmware-directory don yin la'akari da juriya, haɓakawa, da yanayin iya aiki waɗanda ke kan kebul na layin jam'iyyar da aka haɗa da na'urorin masu amfani. A duk lokacin da aka danna ɗaya daga cikin maɓallan null na Model 545DC, ko kuma aka yi amfani da aikace-aikacen mai sarrafa ST, da'irar dijital tana daidaita matasan da ke da alaƙa don cimma matsakaicin asarar dawowar sa cikin ƙasa da daƙiƙa 15. Yayin da tsarin tursasawa ke atomatik, yana faruwa ne kawai akan buƙatar mai amfani. Ana adana ma'auni mara kyau da aka haifar a cikin ƙwaƙwalwar mara mara ƙarfi.

Pro Audio Quality

Model 545DC's audio circuitry an ƙera shi a cikin ruhun ƙwararrun kayan aikin mai jiwuwa maimakon wanda aka samo a cikin kayan haɗin gwiwar layin jam'iyya na yau da kullun. Ana amfani da kayan aiki masu girma a ko'ina, suna ba da ƙarancin murdiya, ƙaramar amo, da babban ɗakin kai. Yin amfani da matattara masu aiki, mitar amsawar tashoshi masu jiwuwa an iyakance shi zuwa 100 Hz zuwa 8 kHz. An zaɓi wannan kewayon don samar da kyakkyawan aiki don magana ta ɗan adam yayin da ake haɓaka ƙarfin da'irori don ƙirƙirar "nulls" mai mahimmanci.

Mitar Audio

Model 545DC ya ƙunshi nau'i biyu na mita matakin LED mai kashi 5. Kowane saitin mita biyu yana nuna matakin siginar da ake aika zuwa da karɓa daga hanyar haɗin layin jam'iyya. A lokacin shigarwa da saita mita suna da kima wajen taimakawa wajen tabbatar da aiki daidai. Yayin aiki na yau da kullun, mitoci suna ba da saurin tabbatar da siginar sauti masu gudana zuwa ciki da waje na naúrar 545DC Model.

Nunin Matsayi

Ana ba da alamun LED akan Model 545DC's gaban panel, suna ba da alamar matsayi na tushen wutar lantarki na jam'iyyar, ayyukan layin jam'iyya, da ayyukan banza. Wasu LEDs guda biyu suna ba da nuni kai tsaye na abin da tushen ko tushen wutar lantarki ke haɗa zuwa Model 545DC. Aikace-aikacen STcontroller kuma yana ba da nunin matsayin “mai kama-da-wane” na ainihin tushen tushen wutar lantarki na PL, ayyukan PL, da ayyukan banza.

Kira Tallafin Haske

Yawancin da'irori na layi-layi na jam'iyyar-tashar guda ɗaya suna ba da aikin hasken kira ta hanyar DC voltage shafi hanyar audio. Model 545DC na iya gano irin wannan aikin haske na kira, yana canza shi zuwa sautin sauti na 20 kHz wanda sannan ana jigilar shi akan hanyar odiyon Dante. Model 545DC naúrar a “ƙarshe mai nisa” zai gano sautin “kira” kuma ya sake haɓaka shi azaman vol na DC.tage a kan hanyar jam'iyya-line intercom audio hanya. Wannan yana ba da damar cikakken goyan bayan haske na kira "ƙarshe-zuwa-ƙarshe" tsakanin Model 545DC guda biyu. Hakanan yana ba da damar Model 545DC don aikawa da karɓar matsayin hasken kira tare da haɗin haɗin Model 545DR Intercom Intercom. Model 545DR yawanci ana amfani dashi tare da jerin RTS TW na bel ɗin mai amfani da layi na tashoshi biyu, gami da mashahurin BP-325.

Bayanan Ethernet, PoE, da Tushen wutar lantarki na DC

Model 545DC yana haɗi zuwa cibiyar sadarwar bayanan yanki (LAN) ta amfani da madaidaicin 100 Mb/s Twied-pair Ethernet interface. Haɗin haɗin jiki yana yin ta ta hanyar jack ɗin Neutrino ether Con RJ45. Yayin da ya dace da daidaitattun matosai na RJ45, jakin ether CON yana ba da damar haɗin kai mai kauri da kulle don matsananci ko babban abin dogaro. Model 545DC ikon aiki za a iya samar da ta hanyar Ethernet dubawa ta amfani da Power-over-Ethernet (PoE) misali. Wannan yana ba da damar haɗin kai cikin sauri da inganci tare da hanyar sadarwar bayanai masu alaƙa. Don tallafawa sarrafa wutar lantarki na PoE, Model 545DC's PoE interface yana ba da rahoto ga kayan aikin samar da wutar lantarki (PSE) cewa na'ura ce ta aji 3 (tsakiyar wuta). Hakanan ana iya kunna naúrar ta amfani da tushen waje na 12 volts DC.

Don sakewa, ana iya haɗa tushen wutar lantarki duka a lokaci guda. Samar da wutar lantarki ta yanayin sauyawa na ciki yana tabbatar da cewa duk fasalulluka na 545DC, gami da layin jam'iyya-layi na intercom, suna samuwa lokacin da naúrar ke aiki ta kowane tushe. LEDs guda hudu a kan bayanan baya suna nuna matsayin haɗin yanar gizon, Dante interface, da kuma tushen wutar lantarki na PoE.

Sauƙaƙen Shigarwa

Model 545DC yana amfani da daidaitattun masu haɗawa don ba da damar haɗin kai cikin sauri da dacewa. Ana haɗa siginar Ethernet ta amfani da jack ɗin Neutrino ether Con RJ45. Idan Power-over-Ethernet (PoE) yana samuwa aiki zai fara nan da nan. Ana iya haɗa tushen wutar lantarki na waje na 12 volts DC ta hanyar haɗin XLR mata 4-pin. Ana yin haɗin haɗin layi-layi ta ƙungiya ta amfani da masu haɗin XLR na maza 3-pin biyu. Model 545DC an ajiye shi a cikin katafaren katafaren aluminium mai nauyi amma mai nauyi wanda aka ƙera don zama mai tauri. Ana iya amfani da shi azaman naúrar ɗaukuwa mai ɗaukuwa, tana goyan bayan abin da aka sani a duniyar watsa shirye-shirye azaman aikace-aikacen “jefa-ƙasa”. Akwai nau'ikan zaɓi na hawan rack waɗanda ke ba da damar ɗaga raka'a 545DC Model ɗaya ko biyu a cikin sarari ɗaya (1U) na daidaitaccen shinge na inch 19.

Futurewarewa na gaba da Sabunta Firmware

Model 545DC an ƙera shi ta yadda za a iya haɓaka iyawarsa da aikinsa cikin sauƙi a nan gaba. Wurin ajiyar USB, wanda ke kan Model 545DC's back panel, yana ba da damar sabunta aikace-aikacen firmware (wanda aka haɗa da software) ta amfani da kebul na USB. Don aiwatar da ƙa'idar Dante ta Model 545DC tana amfani da haɗin haɗin Ultimo™ daga Inordinate. Ana iya sabunta firmware a cikin wannan haɗaɗɗiyar da'irar ta hanyar haɗin Ethernet yana taimakawa don tabbatar da cewa ƙarfinsa ya kasance har zuwa yau.

Farawa

A cikin wannan sashe, za a zaɓi wuri don Model 545DC. Idan ana so, za a yi amfani da kit ɗin shigarwa na zaɓi don ɗaga naúrar a cikin yankan panel, bangon bango, ko tarkacen kayan aiki. Za a yi haɗin haɗin sigina ta amfani da masu haɗin bangon baya na naúrar. Haɗi zuwa da'irori ɗaya ko biyu da ake da su na layi na jam'iyya ko ɗaya ko fiye na'urorin mai amfani da layin jam'iyya za a yi ta amfani da masu haɗin XLR 3-pin. Haɗin bayanan Ethernet, yawanci wanda ya haɗa da damar Power-over-Ethernet (PoE), za a yi ta amfani da madaidaicin kebul na facin RJ45. Mai haɗin XLR mai 4-pin yana ba da damar haɗin tushen wutar lantarki 12 volts DC.

Me Ya Hada

Haɗe a cikin kwalin jigilar kaya akwai Model 545DC Intercom Intercom da umarni kan yadda ake samun kwafin lantarki na wannan jagorar. Kayan shigarwa na zaɓin yana ba da damar Model 545DC don a ɗaura shi a cikin buɗaɗɗen rectangular a saman tebur ko haɗe zuwa saman fili. Idan rukunin 545DC Model ɗaya ko biyu za a ɗora su a cikin rakiyar kayan aiki 19-inch to ana buƙatar samun wani na zaɓin kayan sakawa na rack-mount. Idan an sayi kayan shigarwa da yawanci ana jigilar su a cikin wani kwali na daban. A matsayin na'urar da za a iya kunna ta Power-over-Ethernet (PoE) ko tushen waje na 12 volts DC, babu tushen wutar lantarki da aka haɗa. (Madaidaicin wutar lantarki, Studio Technologies'PS-DC-02, yana samuwa azaman zaɓi.)

Gano Model 545DC

Inda za a sami Model 545DC zai dogara ne da samun damar shiga layin layin jam'iyya mai alaƙa ko wayoyi da aka tanadar don na'urorin mai amfani da ake so. Bugu da kari, dole ne a samar da naúrar ta yadda haɗin keɓaɓɓen siginar Ethernet shima zai yiwu. Ana jigilar Model 545DC azaman rukunin “jifa” mai ƙunshe da kai wanda ya dace da amfani mai ɗaukuwa ko jeri a wani wuri na dindindin. An shigar da su a kasan chassis an saka masu kariyar “kumburi” (wanda aka fi sani da roba “kafafun”). Waɗannan suna da amfani idan za a sanya naúrar a saman inda za a iya yin ɓarna ko dai shingen Model 545DC ko kayan saman. Koyaya, idan an zartar za'a iya cire "ƙafafun" lokacin shigarwa a cikin yanke panel, dutsen bango, ko shingen tarawa za a yi.

Da zarar an kafa wurin naúrar ta zahiri za a ɗauka cewa igiyar igiyar igiyar igiyar igiyar igiyar igiyar igiyar igiyar igiyar ruwa za ta kasance tsakanin mita 100 (ƙafa 325) na tashar Ethernet a kan hanyar sadarwa mai alaƙa. Idan wannan ba haka bane, to ana iya shawo kan iyakar tsayin gabaɗaya ta hanyar amfani da haɗin haɗin fiber-optic tsakanin Model 545DC mai alaƙa-Ethernet sauya da wani maɓalli na Ethernet wanda ke ɓangare na cibiyar sadarwar gida-yankin aikace-aikacen (LAN). Tare da haɗin haɗin fiber babu dalilin da zai sa ba za a iya rarraba LAN mai goyan bayan Dante fiye da mil ko mil da yawa.

Zaɓuɓɓukan hawa

Yanke Panel ko Hawan Sama Model 545DC Unit
Kit ɗin shigarwa RMBK-10 yana ba da damar Model 545DC ɗaya don a saka shi a cikin yankan panel ko a kan shimfidar wuri.
Kit ɗin yana ƙunshe da madaidaitan madaidaicin madaidaicin madaidaicin madaidaicin madauri guda biyu da 6-32 thread-pitch Phillips-head screws. Koma zuwa Karin Bayani na B don bayanin gani.

Shirya don shigar da kit ɗin ta farko cire sukurorun injin guda huɗu da haɗin gwiwa "kulle kan" masu kariya daga ƙasan Model 545DC's chassis. Ana cire su ta amfani da screwdriver # 1 Phillips. Ajiye mashinan injin guda huɗu da masu karewa huɗu don yuwuwar amfani daga baya.

Don shirya naúrar don hawa a cikin yanke ko wani buɗewa a cikin panel, yi amfani da screwdriver #2 Phillips da screws 6-32 guda biyu don haɗa ɗaya daga cikin madaidaicin madaidaicin madaidaicin gefen hagu (lokacin da viewed daga gaba) na shingen Model 545DC. Gabatar da daidaitaccen madaidaicin sashi kamar yadda gabansa yayi daidai da na'urar gaban Model 545DC. Sukullun za su haɗu tare da ɗigon zaren da za a iya gani a gefen shingen Model 545DC, kusa da gaban naúrar. Yin amfani da ƙarin sukurori guda biyu na 6-32, haɗa sauran madaidaicin sashi a gefen dama na shingen Model 545DC.

Da zarar an shigar da madaidaitan madaidaitan madaidaicin madaidaicin madaidaicin 545DC Model XNUMXDC zai kasance a shirye don a saka shi cikin buɗaɗɗen buɗewa. Aminta naúrar zuwa saman hagu da gefen dama na buɗewa ta amfani da sukurori biyu masu hawa kowane gefe.

Don shirya naúrar da za a ɗora a kan filaye kawai yana buƙatar madaidaicin madaidaicin madaidaicin madaidaicin zuwa Model 545DC a digiri 90 daga yadda ake ɗora su don amfani a cikin yanke panel. Yi amfani da screwdriver #2 Phillips da screws 6-32 guda biyu don haɗa ɗaya daga cikin madaidaicin madaidaicin madaidaicin gefen hagu (lokacin da viewed daga gaba) na yadi.

Gabatar da madaidaicin kamar yadda gabansa yayi daidai da saman saman shingen Model 545DC. Sukullun za su haɗu tare da ɗigon zaren da za a iya gani a gefen shingen Model 545DC, kusa da gaban naúrar. Biyan daidaitawa iri ɗaya, yi amfani da ƙarin sukurori guda 6-32 na injuna don haɗa sauran ma'auni mai tsayi a gefen dama na shingen Model 545DC.

Da zarar an shigar da madaidaitan madaidaitan madaidaitan madaidaicin madaidaicin 545DC Model XNUMXDC zai kasance a shirye don a saka shi a saman fili. Tsare naúrar zuwa saman ta amfani da kusoshi biyu masu hawa kowane gefe.

Hagu- ko Gefen Dama-Hagu Model Ɗayan Ƙirar 545DC
Kit ɗin shigarwa RMBK-11 yana ba da damar Model 545DC ɗaya don hawa a gefen hagu ko dama na sarari ɗaya (1U) na daidaitaccen shinge mai inci 19. Kit ɗin yana ƙunshe da madaidaicin madaidaicin madaidaicin sashi ɗaya, sashi mai tsayi ɗaya, da 6-32 thread-pitch Phillips-head screws. Koma zuwa Karin Bayani na C don bayanin gani.

Shirya don shigar da kit ɗin ta hanyar cire sukurorun injin guda huɗu da haɗin gwiwa "kumburi akan" masu kariya daga ƙasan Model 545DC's chassis. Ana cire su ta amfani da screwdriver # 1 Phillips. Ajiye mashinan injin guda huɗu da masu karewa huɗu don yuwuwar amfani daga baya.

Don shirya naúrar don hawa a gefen hagu na shingen tara, yi amfani da screwdriver #2 Phillips da screws 6-32 guda biyu don haɗa madaidaicin madaidaicin madaidaicin gefen hagu (lokacin da viewed daga gaba) na yadi. Sukullun za su haɗu tare da ɗigon zaren da za a iya gani a gefen shingen Model 545DC, kusa da gaban naúrar. Yin amfani da ƙarin sukurori guda biyu 6-32, haɗa madaidaicin tsayin tsayi a gefen dama na shingen Model 545DC.

Don shirya naúrar don hawa a gefen dama na shingen tara, yi amfani da screwdriver #2 Phillips da screws 6-32 guda biyu don haɗa madaidaicin tsayin daka a gefen hagu na shingen. Yin amfani da ƙarin sukurori guda biyu 6-32, haɗa madaidaicin madaidaicin sashi a gefen dama na shingen Model 545 DC.

Da zarar an shigar da ma'auni mai tsayi da tsayi mai tsayi Model 545DC zai kasance a shirye don a saka shi a cikin kayan aiki da aka keɓe.
sarari ɗaya (1U ko 1.75 inci tsaye) a cikin madaidaicin rak ɗin kayan aiki 19-inch ana buƙata. Kiyaye naúrar a cikin tarkacen kayan aiki ta amfani da sukurori biyu masu hawa kowane gefe.

Rack-Hawa Model Biyu 545DC Raka'a
Ana amfani da kit ɗin shigarwa RMBK-12 don ba da damar Model 545DC raka'a biyu don hawa a sarari ɗaya (1U) na daidaitaccen rakiyar kayan aiki 19-inch. Hakanan za'a iya amfani da kit ɗin don hawa Model 545DC ɗaya da ɗayan samfuran Studio Technologies waɗanda suka dace da RMBK-12, kamar Model 545DR Intercom Interface ko Model 5421 Dante Intercom Audio Engine. Kit ɗin shigarwa na RMBK-12 yana ƙunshe da madaidaicin madaidaicin madaidaicin madaukai guda biyu, faranti guda biyu, faranti guda 6-32 na mashin-pitch Phillips-head screws, da 2-56 thread-pitch Torx ™ T7 na ƙirar injin zaren. Koma zuwa Karin Bayani na D don bayanin gani.

Yi shiri don shigar da kit ɗin ta hanyar cire sukurorun injin guda huɗu da masu kariyar “kumburi” daga ƙasan kowane chassis. Ana cire su ta amfani da screwdriver # 1 Phillips. Ajiye mashinan na'ura takwas da masu kariya takwas don yuwuwar amfani daga baya.

Tare da taimako daga screwdriver #2 Phillips, yi amfani da biyu daga cikin screws 6-32 don haɗa ɗaya daga cikin madaidaicin madaidaicin madaidaicin gefen hagu (lokacin da viewed daga gaba) na ɗayan Model 545DC raka'a. Sukullun za su haɗu tare da ɗigon zaren da za a iya gani a gefen shingen Model 545DC, kusa da gaban naúrar. Yin amfani da ƙarin biyu na 6-32 na'ura mai ba da hanya tsakanin hanyoyin sadarwa, haɗa ɗaya daga cikin faranti na haɗin gwiwa zuwa gefen dama na wannan Model 545DC guda ɗaya.

Sake amfani da biyu daga cikin skru 6-32, haɗa madaidaicin madaidaicin sashi na biyu a gefen dama na Model 545DC na biyu ko wata naúrar da ta dace. Yin amfani da sukurori biyu na 6-32 na ƙarshe, haɗa farantin haɗin gwiwa na biyu a gefen hagu na Model 545DC na biyu ko wata naúrar da ta dace tare da daidaitawar digiri 180 daga hanyar da aka shigar da farantin farko.

Don kammala taron, "haɗa" raka'a tare ta zamewa kowane farantin haɗin haɗin gwiwa ta ɗayan. Gilashin da ke cikin kowane farantin haɗin haɗin gwiwa za su daidaita a hankali tare da juna kuma su samar da ɗanɗano mai ƙarfi. Layi raka'o'i biyu ta yadda bangarorin gaba su zama jirgin sama na gama-gari. Tare da taimakon screwdriver na Torx T7, yi amfani da screws guda biyu na Torx 2-56 don amintar da faranti guda biyu tare. Ya kamata sukurori su dace da kyau a cikin ƙananan buɗe ido da aka kafa ta hanyar mating na faranti biyu masu haɗawa.

Taron na raka'a 2 yanzu yana shirye don a saka shi a cikin kayan aikin da aka keɓe. sarari ɗaya (1U ko 1.75 inci tsaye) a cikin madaidaicin rak ɗin kayan aiki 19-inch ana buƙata. Tsare taro a cikin tarkacen kayan aiki ta amfani da sukurori biyu masu hawa kowane gefe.

Cibiyar Rack Dutsen Model Daya 545DC Unit
Kit ɗin shigarwa RMBK-13 yana ba da damar Model 545DC ɗaya don hawa a tsakiyar sarari ɗaya (1U) na daidaitaccen shinge mai inci 19. Kit ɗin yana ƙunshe da madaidaicin madaidaicin tsayi biyu da 6-32 thread-pitch Phillips-head screws. Koma zuwa Karin Bayani E don bayanin gani.

Shirya don shigar da kit ɗin ta hanyar cire sukurorun injin guda huɗu da haɗin gwiwa "kumburi akan" masu kariya daga ƙasan Model 545DC's chassis. Ana cire su ta amfani da screwdriver # 1 Phillips. Ajiye mashinan injin guda huɗu da masu karewa huɗu don yuwuwar amfani daga baya.

Don shirya naúrar don hawa a tsakiyar shingen rak, yi amfani da screwdriver #2 Phillips da screws 6-32 guda biyu don haɗa ɗaya daga cikin maƙallan matsakaicin tsayi a gefen hagu (lokacin da viewed daga gaba) na yadi. Sukullun za su haɗu tare da ɗigon zaren da za a iya gani a gefen shingen Model 545DC, kusa da gaban naúrar. Yin amfani da ƙarin sukurori guda biyu na 6-32, haɗa sauran madaidaicin sashi a gefen dama na shingen Model 545DC.

Da zarar an shigar da ɓangarorin matsakaicin tsayi biyu na Model 545DC zai kasance a shirye don a saka shi cikin rakiyar kayan aiki da aka keɓe. sarari ɗaya (1U ko 1.75 inci tsaye) a cikin madaidaicin rak ɗin kayan aiki 19-inch ana buƙata. Kiyaye naúrar a cikin tarkacen kayan aiki ta amfani da sukurori biyu masu hawa kowane gefe.

Haɗin Ethernet tare da PoE

Ana buƙatar haɗin Ethernet wanda ke goyan bayan 100 BASE-TX (100 Mb/s akan karkatattun-biyu) don aikin Model 545 DC. Haɗin BASE-T 10 bai isa ba; Ba a tallafawa haɗin 1000 BASE-T (GigE) sai dai idan zai iya "fadi baya" ta atomatik zuwa aikin 100 BASE-TX. An fi son haɗin Ethernet wanda ke goyan bayan Power-over-Ethernet (PoE) kamar yadda kuma zai samar da ikon aiki don Model 545 DC. Don tallafawa canjin Poe Ethernet (PSE) wanda ya haɗa da ikon sarrafa wutar lantarki Model 545 DC zai ƙididdige kansa azaman na'urar PoE class 3.

Ana yin haɗin 100 BASE-TX Ethernet ta hanyar jack Neutrino ether CON RJ45 wanda ke kan bangon baya na Model 545DC. Wannan yana ba da damar haɗi ta hanyar filogin ether CON mai ɗorewa ko madaidaicin filogin RJ45. Ba za a taɓa buƙatar kebul na crossover ba kamar yadda Model 545DC's Ethernet interface ke goyan bayan MDI/MDI-X ta atomatik. Dangane da ma'auni na Ethernet, iyakance tsawon na'urar Ethernet Canja-zuwa-Ethernet don igiyar igiyar igiyar igiya-biyu shine mita 100 (ƙafa 325).

Input DC 12 Volt na waje

Ana iya haɗa tushen waje na 12 volts DC zuwa Model 545DC ta hanyar haɗin XLR na namiji 4-pin wanda ke kan ɓangaren baya na naúrar.
Yayin da abin da ake buƙata don tushen waje shine 12 volts DC, daidaitaccen aiki zai gudana akan kewayon 10 zuwa 18 volts DC. Model 545DC yana buƙatar matsakaicin halin yanzu na 1.0 amperes don aiki daidai. Ya kamata a dakatar da tushen DC akan mai haɗin XLR mata 4-pin tare da fil 1 korau (-) da fil 4 tabbatacce (+); fil 2 da 3 ya kamata su kasance batattu. An saya azaman zaɓi, wutar lantarki ta PS-DC-02, wanda ake samu daga Studio Technologies, yana dacewa kai tsaye. Shigar da wutar lantarki ta AC yana ba da damar haɗi zuwa 100-240 volts, 50/60 Hz kuma yana da 12 volts DC, 1.5 ampmafi girman fitarwa da aka ƙare akan mahaɗin mata 4-pin.

Kamar yadda aka tattauna a baya, haɗin Ethernet wanda ke ba da damar Power-over-Ethernet (PoE) zai iya zama tushen wutar lantarki na Model 545DC. A madadin, ana iya haɗa tushen 12 volts DC na waje.
Don sakewa, duka PoE da na waje 12 volts DC tushen za a iya haɗa su a lokaci guda. Idan an haɗa duka PoE da na waje na 12 volts DC tushen, za a jawo wutar lantarki daga wadatar PoE kawai. Idan tushen PoE ya zama mara aiki, tushen 12 volts DC zai samar da ikon Model 545DC ba tare da katsewa cikin aiki ba. (Tabbas, idan duka bayanan bayanan PoE da Ethernet sun ɓace wannan lamari ne na daban!)

Haɗin Intanet na Party-Line

Model 545DC's guda biyu musaya na layi na jam'iyya-line intercom an tsara su don yin aiki da kansu ta hanyoyi guda biyu. Ana iya haɗa su zuwa da'irori mai zaman kansa "mai ƙarfi" ɗaya tashoshi ɗaya-layi na intercom. A madadin haka, ana iya haɗa su kai tsaye zuwa na'urorin masu amfani da layi-layi na jam'iyya.Tsarin layin intercom na jam'iyyar-line-tashar guda ɗaya, sau da yawa hade da kayan aiki daga Clear-Com, zai sami ikon DC da tashar sauti ɗaya akan mai haɗin XLR 3-pin. Za a yi amfani da waɗannan masu haɗin kai kamar yadda na kowa ke kan fil 1, 28 zuwa 32 volts DC yana kan fil 2, kuma sautin magana yana nan akan fil 3. Da'irar intercom na jam'iyya mai lamba ɗaya tashoshi zai kuma haɗa da cibiyar sadarwa mai haɓaka impedance. wanda ke ba da nauyin 200 ohms audio (AC) daga fil 3 zuwa fil 1. (Kuma a wasu lokuta, siginar "kira" na DC na iya, idan an zartar, kuma yana kasancewa akan fil 3.) Lokacin da Model 545DC's party-line interface. an haɗa shi da da'irar intercom da ke akwai zai yi aiki, daga yanayin sauti, kama da na daidaitaccen na'urar mai amfani da layin jam'iyya-line.
Model 545DC's interface ba zai zana (amfani) kowane ikon DC daga fil 2 ba ko da yake yana da ikon yin amfani da DC "kira" vol.tage na pin 3.

Model 545DC's biyu na layin layi na jam'iyya kuma na iya yin aiki don ƙirƙirar da'irori "ƙananan" guda biyu. Kowannensu yana ba da tushen wutar lantarki ta intercom tare da janareta na impedance 200 ohms, yana ba da damar iyakance adadin na'urorin masu amfani da intercom guda ɗaya tashoshi kai tsaye. Kowane Model 545DC's intercom musaya zai iya samar da 28 volts DC akan fil 2 tare da matsakaicin halin yanzu na 150mA. Duk da yake yana da sauƙi, wannan adadin ƙarfin zai iya zama da amfani sosai amma yana buƙatar nau'in da adadin na'urorin masu amfani da aka haɗa da kyau. Yawancin aikace-aikacen nishaɗi suna amfani da fakitin bel na Clear-Com RS-501 da kuma Model 545DC intercom na iya tallafawa kai tsaye zuwa uku daga cikinsu. Aikace-aikacen da ke amfani da sabbin kuma mafi inganci mai ƙarfi Clear-Com RS-701 yakamata su ba da damar haɗa har zuwa biyar don haɗawa da sarrafa su ta kowane Model 545DC intercom circuit. Waya daga Model 545DC intercom interface's 3-pin namiji XLR haši zuwa na'urorin masu amfani suna buƙatar kiyaye tsarin wayoyi 1-zuwa-1, 2-zuwa-2, 3-zuwa-3 akan masu haɗin XLR 3-pin.

Dace da 2-Channel Intercom Systems
Kamar yadda aka tattauna a baya, Model 545DC an ƙirƙira shi don tallafawa kai tsaye da'irori guda biyu na layin jam'iyyar-layi da ƙungiyoyin na'urorin masu amfani. Hakanan yana yiwuwa aikace-aikacen da suka haɗa da da'ira-line intercom na jam'iyyar-tashar 2-tashar da na'urorin masu amfani (yawanci masu alaƙa da jerin samfuran RTS TW) ana iya tallafawa. Wadannan da'irori da na'urori yawanci suna amfani da haɗin gama gari akan fil 1, 28 zuwa 32 volts DC da tashar 1 audio akan fil 2, da tashar tashar 2 akan fil 3. Lokacin da kewayar tashar tashoshi 2 ko na'ura aka haɗa zuwa Model 545DC, kawai tashar na'urar 2 za ta kasance mai aiki; tashar na'urar 1 ba za ta yi aiki ba. Hanya mafi kyau don tallafawa waɗannan da'irori na tashoshi 2 da na'urori shine amfani da Intercom Model 545DR Intercom Intercom Studio Technologies. Wannan rukunin, "dan uwan" na Model 545DC, an inganta shi don aikace-aikacen intercom na jam'iyyar-tashar 2. Maimakon samar da musaya guda biyu na tashoshi guda ɗaya Model 545DR yana samar da hanyar sadarwa guda biyu. Ana samun cikakken bayani game da Model 2DR akan Studio Technologies' website.

Teaddamarwar Dante

Don haɗa Model 545DC cikin aikace-aikacen yana buƙatar saita adadin sigogi masu alaƙa da Dante. Za a adana waɗannan saitunan saitin a cikin ƙwaƙwalwar da ba ta da ƙarfi a cikin Model 545DC's Dante interface circuitry. Kanfigareshan yawanci za a yi ta amfani da aikace-aikacen software na Dante Controller wanda ke samuwa don saukewa kyauta a audinate.com. Akwai nau'ikan Dante Controller don tallafawa tsarin aiki na kwamfuta na sirri na Windows da macOS. Model 545DC yana amfani da UltimoX2 2-input/2-fitarwa hadedde da'ira don aiwatar da aikin Dante. Model 545DC's Dante interface ya dace da aikace-aikacen software na Dante Domain Manager (DDM).

Audio Routing

Tashoshi biyu na Dante mai watsawa (fitarwa) akan kayan aikin da aka haɗa yakamata a tura su (basu rijista) zuwa tashoshi biyu na Dante mai karɓa (shigarwar) Model 545DC.
Model 545DC's biyu na Dante transmitter (fitarwa) tashoshi ya kamata a ruguza (subscribe) zuwa tashoshi biyu na Dante mai karɓa (shigarwar) akan kayan haɗin gwiwa.
Wannan yana samun haɗin haɗin sauti na Model 545DC ta tashoshin intercom guda biyu na layi tare da cibiyar sadarwar Dante da na'urar Dante mai alaƙa ko na'urori.

A cikin Dante Controller "biyan kuɗi" shine kalmar da aka yi amfani da ita don sarrafa tashar watsawa ko gudana (rukuni na har zuwa tashoshin fitarwa hudu) zuwa tashar mai karɓa ko gudana (rukuni na har zuwa tashoshin shigarwa hudu). Adadin kwararar mai watsawa da ke da alaƙa da haɗaɗɗiyar da'irar UltimoX2 an iyakance zuwa biyu. Waɗannan na iya zama ko dai su zama unicast, multicast, ko haɗin biyun. Idan Model 545DC's transmitter (fitarwa) tashoshi na bukatar a ruguza ta yin amfani da fiye da biyu kwarara yana yiwuwa na'urar tsaka-tsaki, kamar Studio Technologies 'Model 5422A Dante Intercom Audio Engine, za a iya amfani da su "maimaita" sigina.

Model 545DC raka'a za a yawanci amfani da a daya daga biyu na kowa jeri: "point-to-point" ko a hade tare da sauran Dante-enabled kayan aiki. Tsarin farko zai yi amfani da Model 545DC guda biyu waɗanda ke "aiki" tare don haɗa wurare biyu na zahiri. A kowane wuri ko dai za a kasance da'ira-line intercom na jam'iyya ko saitin na'urorin intercom masu amfani (kamar fakitin bel). Ƙungiyoyin Model 545DC guda biyu za su yi aiki da "ma'ana-zuwa-ma'ana," haɗin kai ta hanyar hanyar sadarwar Ethernet mai alaƙa. Don aiwatar da wannan aikace-aikacen abu ne mai sauqi qwarai. Tashar Daga Layin Jam'iyya Tashoshi akan kowace raka'a za'a tura shi (yi rijista) zuwa tashar Zuwa Party-Line Channel akan ɗayan rukunin.
Kuma tashar Daga Party-Line Channel B akan kowane raka'a za'a tura su zuwa tashar B ta hanyar Party-Line akan ɗayan rukunin.

Sauran aikace-aikacen na yau da kullun za su sami Model 545DC guda ɗaya da aka haɗa zuwa da'irar intercom-layin jam'iyya mai gudana ko saitin na'urorin masu amfani. Sannan tashoshin sauti na Dante na naúrar za a tura su (subscribe) zuwa tashoshi na Dante transmitter (fitarwa) da tashoshi mai karɓa (shigarwar) akan kayan aikin Dante masu alaƙa.
Tsohonampna wannan kayan aiki na iya zama tsarin RTS ADAM matrix intercom wanda ke ba da damar haɗin gwiwar Dante ta amfani da katin ƙirar OMNEO. Tashoshi masu jiwuwa akan Model 545DC za a tura su zuwa kuma daga tashoshin sauti akan katin OMNEO. Sauran kayan aikin da ke goyan bayan Dante, irin su na'ura mai jiwuwa ko musaya mai jiwuwa (Dante-to-MADI, Dante-to-SDI, da dai sauransu), na iya samun tashoshi masu jiwuwa (subscribe) zuwa kuma daga Model 545DC.

Na'ura da Sunayen Channel

Model 545DC yana da tsoho sunan na'urar Dante na ST-545DC- wanda ke biye da suffix na musamman. (Dalilin fasaha ya hana sunan tsoho ya zama ST-M545DC da aka fi so- (wanda aka haɗa da "M"). Amma mai amfani zai iya ƙara wannan. Haƙiƙanin haruffan alpha da/ko lambobi suna da alaƙa da adireshin MAC na haɗin haɗin haɗin UltimoX545 na rukunin. Tashoshi biyu na Dante masu watsawa (fitarwa) naúrar suna da tsoffin sunaye daga Ch A kuma Daga Ch B. Tashoshin masu karɓar Dante guda biyu na Theunit suna da tsoffin sunayen Ku PL Ch A kuma Ku PL Ch B. Amfani da Dante Controller, tsoho na'urar da sunayen tashoshi za a iya bita kamar yadda ya dace da takamaiman aikace-aikace.

Kanfigareshan Na'ura

Model 545DC yana goyan bayan s mai jiwuwa kawaiampƙimar 48 kHz ba tare da ƙima mai ƙima/ ja-sau da ake samu ba. An gyara rikodin rikodin sauti don PCM 24. Ana iya daidaita Latency na Na'ura da Clocking idan an buƙata amma ƙimar tsoho yawanci daidai ne.

Kanfigareshan hanyar sadarwa – Adireshin IP

Ta hanyar tsoho, adireshin IP na Dante na Model 545DC da sigogin cibiyar sadarwar da ke da alaƙa za a ƙayyade ta atomatik ta amfani da DHCP ko, idan ba a samu ba, ƙa'idar hanyar sadarwar gida-gida. Idan ana so, Dante Controller yana ba da damar adireshin IP da sigogin cibiyar sadarwar da ke da alaƙa don saita da hannu zuwa ƙayyadaddun tsari (tsaye). Duk da yake wannan tsari ne da ya ƙunshi fiye da barin DHCP kawai ko haɗin kai-na gida "yi abin nasu," idan kafaffen magana ya zama dole to wannan damar tana samuwa. A wannan yanayin, ana ba da shawarar sosai cewa naúrar a yi alama a zahiri, misali, kai tsaye ta amfani da alamar dindindin ko “console tef,” tare da takamaiman adireshin IP ɗin sa. Idan sanin adireshin IP na Model 545DC ya ɓace babu maɓallin sake saiti ko wata hanya don mayar da naúrar cikin sauƙi zuwa saitunan IP na asali.

Kanfigareshan AES67 - Yanayin AES67
Ana iya saita Model 545DC don aikin AES67. Wannan yana buƙatar Yanayin AES67 don saita don Kunnawa. Ta hanyar tsoho, an saita yanayin AES67 don Naƙasassu.
Lura cewa a cikin yanayin AES67 tashoshi na Dante transmitter (fitarwa) za su yi aiki a multicast; unicast baya tallafawa.

Model 545DC Tushen agogo
Duk da yake a zahiri Model 545DC na iya zama agogon Jagora don cibiyar sadarwar Dante (kamar yadda duk na'urorin da ke kunna Dante) a kusan dukkanin lokuta za a saita naúrar don karɓar “sync” daga wata na'ura. Don haka, akwatin rajistan Jagoran da aka zaɓa wanda ke da alaƙa da Model 545DC ba zai so a kunna shi ba.

Model 545DC Kanfigareshan

Ana amfani da aikace-aikacen software na STcontroller don daidaita ayyukan Model 545DC guda biyu, tallafin haske, da gano aiki na PL. (Stcontroller kuma yana ba da damar nunin lokaci na ainihi da sarrafa sauran ayyukan Model 545DC.
Wadannan ayyuka za a yi dalla-dalla a cikin sashin Aiki.) Ba a yi amfani da saitunan sauya DIP ko wasu ayyuka na gida don daidaita sashin. Wannan ya sa ya zama wajibi cewa STcontroller ya kasance don dacewa da amfani akan kwamfuta na sirri wanda ke da alaƙa da LAN mai alaƙa.

Sanya STcontroller

Ana samun STcontroller kyauta akan Studio Technologies' website (studio-tech.com). Siffofin su ne
akwai waɗanda suka dace da kwamfutoci na sirri waɗanda ke gudanar da zaɓaɓɓun nau'ikan tsarin aiki na Windows da macOS. Idan an buƙata, zazzagewa kuma shigar da STcontroller akan keɓaɓɓen kwamfuta na sirri. Dole ne wannan kwamfuta ta sirri ta kasance a kan cibiyar sadarwa ta gida ɗaya (LAN) da kuma subnet kamar ɗaya ko fiye Model 545DC raka'a waɗanda za a daidaita su. Nan da nan bayan fara STcontroller aikace-aikacen zai gano duk na'urorin Studio Technologies waɗanda zai iya sarrafawa. Model 545DC raka'a da za a iya daidaita za su bayyana a cikin jerin na'urar. Yi amfani da ƙayyadaddun umarni don ba da izinin ganewa cikin sauƙi na takamaiman naúrar 545DC ta musamman. Danna sau biyu akan sunan na'ura zai sa menu na daidaitawa mai alaƙa ya bayyana. Review daidaitawar halin yanzu da yin kowane canje-canjen da ake so.

Canje-canje na daidaitawa da aka yi ta amfani da STcontroller za a nuna su nan da nan a cikin aikin naúrar; babu Model 545DC sake yi da ake buƙata. A matsayin nuni da cewa an yi canjin sanyi LEDs guda biyu masu alaƙa da ikon shigarwa, masu lakabi DC da PoE, akan gaban Model 545DC na gaba zai haskaka a cikin wani tsari na musamman.

Tsarin - Taimakon Hasken Kira

Zaɓuɓɓuka suna Kashe da Kunnawa.
A cikin mai sarrafa ST, aikin daidaitawar Taimakon Hasken Kira yana ba da damar kunna aikin goyan bayan hasken kira kamar yadda ake so. Lokacin da aikin ke Kunna, ana kunna aikin goyan bayan hasken kira. Lokacin da aka zaɓi saitin Tallafin Hasken Kira don Kashe aikin yana kashe. Don yawancin aikace-aikacen aikin goyan bayan hasken kira yakamata ya kasance a kunne. Yanayi na musamman ne kawai zai cancanci kashe aikin.

Tsarin – PL Active Gane

Zaɓuɓɓuka suna Kashe da Kunnawa.
Aikin gano Model 545DC na yanzu don mu'amalar layin jam'iyya zai yi aiki lokacin da aka kunna tushen wutar gida biyu kuma an zaɓi saitin Gano Active PL don Kunnawa. Lokacin da aka zaɓi waɗannan sigogi biyu mafi ƙarancin halin yanzu na 5 mA (masu ƙima) dole ne a zana su daga fil 2 na ƙirar PL don Model 545DC don gane yanayin "PL aiki". Lokacin da wannan ƙaramar yanayin halin yanzu ya cika LED mai lakabin Active na takamaiman tashar zai haskaka kore, alamar matsayin PL Active akan shafin menu na STcontroller zai nuna kore, kuma hanyar mai watsawa ta Dante (fitarwa) zai kasance mai aiki.
Samun aikin Gano Active na PL ya dace da yawancin aikace-aikacen, yana taimakawa wajen kiyaye ingantaccen aikin sauti. Sai kawai lokacin da aka zana isasshiyar halin yanzu daga fil 2 na dubawa za a aika da sauti daga wannan tashar PL ta tashar watsawa ta Dante (fitarwa).

Lokacin da aka zaɓi saitin Ganewar Active PL zuwa Kashe (an kashe), ba a buƙatar mafi ƙarancin zane na yanzu akan fil 2 na ko dai na musaya na PL don kunna LED Active su, gumakan masu sarrafa ST don nuna kore, da Dante. tashoshin watsawa (fitarwa) don aiki. Duk da haka, kawai a cikin musamman
yanayi zai dace da daidaitawar PL Active Detection da aka zaɓa don Kashe.

Tsohonampinda Kashe zai dace zai zama yanayin da ake amfani da Model 545DC tare da na'urar hasashe wanda ke da haɗin layin jam'iyya mai tashoshi guda ɗaya wanda baya jan wutar DC. Wannan naúrar na iya tsammanin za a haɗa shi zuwa da'irar intercom ta amfani da mai haɗin XLR 3-pin tare da na kowa akan fil 1, ikon DC akan fil 2, da kuma sautin 3. Model 545DC na iya samar da da'irar PL mai dacewa lokacin da tushen wutar lantarki na gida yake. kunna. Amma matsala na iya tasowa saboda wannan rukunin bazai iya zana halin yanzu daga fil 2 na Model 545DC's PL intercom circuit. Maiyuwa baya aiki ta hanya ɗaya da na al'ada PL intercom beltpack ko na'urar mai amfani. Ba zai yi amfani da wuta daga haɗin PL ba, maimakon yin amfani da tushen wutar lantarki na ciki don aiki. A wannan yanayin, Model 545DC's party-line interface ba zai samar da halin yanzu ba, LED Active ba zai yi haske ba, gunkin mai aiki a cikin mai sarrafa ST ba zai zama kore ba, kuma ba za a kunna hanyar sauti ta Dante (fitarwa) ba. Masu amfani da na'urar za su karɓi Model 545DC Dante mai karɓar sauti (shigarwa) amma ba za su aika da sautin tashar Dante mai watsawa (fitarwa). Yin amfani da mai sarrafa ST don kashe aikin Gano Active PL zai warware wannan batun. Ko da yake ba za a iya samar da halin yanzu na DC ta Model 545DC's PL interface, za a kunna tashar watsawa ta Dante (fitarwa) kuma za a iya aiwatar da aikin dubawar PL mai nasara.

Lokacin da Model 545DC jam'iyyar-line intercom da'ira da aka saita don ba samar da ikon gida aikin PL Active Gane yana aiki ta wata ɗan daban.
Sai kawai idan DC voltage na kusan 18 ko mafi girma yana nan akan fil 2 na PL dubawa zai Model 545DC gane cewa an yi ingantacciyar hanyar haɗin gwiwa ta PL. A wannan yanayin, LED Active LED na tashar a gaban panel zai haskaka kore, maɓallin kama-da-wane a cikin mai kula da ST zai haskaka kore, kuma tashar mai watsawa ta Dante (fitarwa) don wannan keɓancewar za ta yi aiki. Lokacin da aka kashe aikin Gane Active PL, saka idanu na DC voltage akan fil 2 na Model 545DC's PL musaya ba zai faru ba. A cikin wannan yanayin, LEDs masu aiki a kan Model 545DC's gaban panel za su kasance koyaushe suna haskakawa, za a kunna alamun kama-da-wane a cikin mai sarrafa ST, kuma tashoshin sauti na Dante (fitarwa) za su yi aiki. Ba a ƙayyade aikace-aikacen aikace-aikacen wannan ƙayyadaddun ƙayyadaddun tsarin ba, amma yana shirye idan buƙatar ta taso!

Aiki

A wannan gaba, Model 545DC yakamata ya kasance a shirye don amfani. Ya kamata a yi haɗin haɗin layin jam'iyya da Ethernet. Dangane da aikace-aikacen, ana iya yin tushen waje na ƙarfin 12 volts DC. (Ba a haɗa tushen wutar lantarki na 12 volts DC tare da Model 545DC. Ana iya siyan ɗaya azaman zaɓi.) Tashoshin mai karɓar Dante (shigarwa) da watsawa (fitarwa) yakamata an lalata su ta amfani da aikace-aikacen software na Dante Controller. Aiki na yau da kullun na Model 545DC na iya farawa yanzu.

A gaban panel, LEDs da yawa suna ba da alamar yanayin aiki na naúrar. Bugu da kari, ana samar da maɓallan turawa guda biyu don zaɓar matsayin kunnawa/kashe ayyukan yanayin wutar gida da kunna ayyukan ɓoyayyiyar atomatik. Ana iya amfani da aikace-aikacen software mai sarrafa ST don lura da matsayin wasu yanayin aiki na naúrar. Maɓallin maɓallin turawa na zahiri mai alaƙa da mai sarrafa ST kuma yana ba da damar sarrafa yanayin kunnawa/kashe na yanayin wutar gida ban da ƙaddamar da ayyukan banzar auto.

Aiki na farko

Model 545DC zai fara aikinsa na farko bayan an haɗa tushen wutar lantarki.
Kamar yadda aka tattauna a baya, ana iya samar da ƙarfin naúrar ta Power-over-Ethernet (PoE) ko tushen waje na 12 volts DC. Idan duka biyun sun haɗa tushen PoE zai ƙarfafa naúrar. Idan PoE daga baya ya daina samuwa aiki zai ci gaba da amfani da waje 12 volts DC tushen.

A kan Model 545DC iko da yawa daga cikin matsayi da meter LEDs a gaba da baya panels za su kunna a cikin jerin gwaji. A gefen baya, LED ɗin da ke da alaƙa da ma'ajin USB, mai lakabin Sabuntawar Firmware, zai haskaka kore na ɗan daƙiƙa kaɗan. Ba da daɗewa ba bayan haka Dante SYS da Dante SYNC LEDs za su yi haske ja. Bayan ƴan daƙiƙa kaɗan za su fara nuna matsayin aikin Dante interface, suna juya kore kamar yadda aka kafa ingantattun yanayi. Ethernet LINK/ACT LED, wanda kuma ke kan bangon baya, zai fara haskaka kore don amsa bayanan da ke shiga ciki da waje na keɓancewar Ethernet.

A gaban panel, ikon shigarwa, auto null, partyline intercom circuit status, da matakin mita LEDs za su yi haske a cikin sauri jerin gwaji. Model 545DC yanzu zai fara aiki na yau da kullun. Ainihin hanya
a cikin abin da LINK / ACT, SYS, da SYNC LEDs (duk suna kan bangon baya da ke ƙasa da ether Con RJ45jack) haske zai dogara ne akan halayen da suka danganci siginar Ethernet da aka haɗa da kuma daidaitawar haɗin Dante na naúrar. Za a rufe cikakkun bayanai a sakin layi na gaba. A gaban panel, an gabatar da mai amfani tare da maɓallin turawa guda biyu, matsayi na shigar da wutar lantarki guda biyu, LEDs na layin intercom na jam'iyya guda huɗu, LEDs null LEDs guda biyu, da matakan matakan LED guda huɗu 5. Waɗannan albarkatun suna da sauƙin fahimta da sarrafawa, kamar yadda za a bayyana a cikin sakin layi na gaba.

Ethernet da Dante Yanayin LEDs

Matsayin LEDs guda uku suna ƙarƙashin jack ɗin ether CON RJ45 akan sashin baya na Model 545DC.
LED ɗin LINK/ACT zai haskaka kore a duk lokacin da aka kafa haɗin kai mai aiki zuwa cibiyar sadarwar Ethernet 100 Mb/s. Zai yi walƙiya don amsa ayyukan bayanai. SYS da SYNC LEDs suna nuna matsayi na aiki na Dante interface da haɗin haɗin gwiwa. SYS LED zai haskaka ja akan Model 545DC ikon har zuwa nuna cewa Dante interface bai shirya ba. Bayan ɗan gajeren tazara, zai yi haske kore don nuna cewa a shirye yake don ƙaddamar da bayanai tare da wata na'urar Dante.
SYNC LED zai yi haske ja lokacin da Model 545DCis ba ya aiki tare da cibiyar sadarwar Dante. Zai yi haske mai ƙarfi kore lokacin da Model 545DC ke aiki tare tare da hanyar sadarwar Dante kuma ana karɓar tushen agogon waje (bayanin lokaci). A hankali zai yi haske kore lokacin da wannan takamaiman Model 545DC naúrar ke cikin hanyar sadarwar Dante kuma yana aiki azaman agogon Jagora. (Yana da mahimmanci a lura cewa aikace-aikacen yau da kullun ba za su sami Model 545DC naúrar aiki azaman agogon Jagoran Dante ba.)

Yadda ake Gano Takamaiman Model 545DC
Duk aikace-aikacen software na Dante Controller da ST masu kulawa suna ba da umarnin gano umarnin da za a iya amfani da su don taimakawa gano takamaiman Model 545DC. Lokacin da aka zaɓi umarnin ganowa don takamaiman Model 545DC naúrar LEDs ɗin mitoci za su yi haske a cikin tsari na musamman. Bugu da ƙari, SYS da SYNC LEDs, waɗanda ke ƙasa kai tsaye a ƙasa da ether CON jack a kan bangon baya, za su yi haske a hankali. Bayan 'yan seconds, da LED ganewa alamu zai gushe da al'ada Model 545DC matakin mita da Dante matsayi LED aiki zai sake faruwa.

Matsayin Mita

Model 545DC ya ƙunshi mita matakin LED mai kashi 5 guda huɗu. Ana ba da waɗannan mitoci azaman taimakon tallafi yayin shigarwa, daidaitawa, aiki, da kuma gyara matsala. Mitoci suna wakiltar ƙarfin siginar sauti da ke zuwa da kuma fitowa daga da'irar intercom-line-party.

Gabaɗaya

An tsara mitoci zuwa rukuni biyu tare da kowane rukuni mai wakiltar tashar sauti guda ɗaya ana aika zuwa da'irar layin jam'iyya kuma tashar sauti guda ɗaya ana mayar da ita ta hanyar layin jam'iyya. An ƙirƙira mitoci don nuna matakin a dB dangane da matakin nuni (na ƙima) na da'ira-line intercom. Model 545DC's nominal party-line-line level an zaba ya zama -14 dBu, wanda ya dace da abin da aka saba amfani da shi ta hanyar da'irar layi na jam'iyyar-layi guda ɗaya. (Lura cewa farkon tsarin Clear-Com guda ɗaya yana da matakin ƙididdiga na -20 dBu amma wannan ba gaskiya bane ga raka'a na zamani.)

Kowane mitar matakin ya ƙunshi koren LED guda huɗu da LED mai rawaya ɗaya. Ledojin kore guda huɗu suna nuna matakan siginar tashar intercom na layin jam'iyya waɗanda ke a ko ƙasa -14 dBu. Babban LED ɗin rawaya ne kuma yana nuna sigina da ke 6 dB ko mafi girma fiye da matakin ƙima -14 dBu. Siginonin sauti waɗanda ke haifar da fitilun rawaya zuwa haske ba lallai ba ne suna nuna yanayin matakin da ya wuce kima, amma suna ba da faɗakarwa cewa rage matakin siginar na iya zama da hankali. Aiki na yau da kullun tare da matakan sigina na yau da kullun yakamata nemo hasken mita kusa da maki 0. Kololuwar sigina na iya sa LED mai launin rawaya ya yi walƙiya.
LED mai launin rawaya wanda ke haskakawa cikakke yayin aiki na yau da kullun zai nuna girman daidaitawar matakin sigina da/ko matsalar daidaitawa tare da kayan aikin Dante mai alaƙa.

A matsayin exampyadda mita ke aiki, bari mu sakeview halin da ake ciki inda tashar A To meter yana da LEDs uku na kasa (-18, -12, da -6) masu haske da 0 LED kawai da kyar. Wannan zai nuna cewa ana aika sigina tare da kimanin matakin -14 dBu zuwa tashar intercom na layi na jam'iyyar A. Wannan zai zama matakin siginar da ya dace kuma ya kamata ya samar da kyakkyawan aiki. (Har ila yau, lura cewa siginar -14 dBu da ake aika zuwa tashar intercom-line-line A zai nuna cewa siginar sauti na dijital -20 dBFS yana nan akan tashar mai karɓar Dante (shigarwar) A. Wannan ya faru ne saboda zaɓin Studio Technologies - 20 dBFS azaman matakin tunani (masu ƙima) don tashoshin sauti na Dante.)

Matakan Sigina Mara Kyau

Idan ɗaya ko fiye na mita suna nuna matakan da ke ƙasa ko mafi girma fiye da ma'anar 0 yana yiwuwa akwai matsalar daidaitawa. Wannan yawanci yana da alaƙa da saitunan da ba daidai ba akan kayan aikin da aka haɗa zuwa tashoshi masu karɓa na Dante (shigarwa) da/ko Dante transmitter (fitarwa). (Ba zai yuwu ba don wannan yanayin ya faru idan an saita raka'a 545DC Model guda biyu "madaidaicin ma'ana" kamar yadda ba a samar da daidaitaccen matakin sauti na dijital na Dante. an sanya shi zuwa takamaiman tashar ko tashar jiragen ruwa. Domin misaliample, tsarin RTS/Telex/Bosch ADAM yana da matakin sauti na ƙima da aka buga na +8 dBu, amma ba a bayyana yadda wannan ke fassara zuwa matakin sauti na dijital akan tashar Dante ko OMNEO mai alaƙa ba. (OMNEO shine kalmar da RTS ke amfani da ita don komawa zuwa tashar jiragen ruwa na Dante.) Yin amfani da software na AZedit yana yiwuwa a saita matakin ƙididdiga na maɓallan maɓalli na intercom ko tashar jiragen ruwa zuwa wani abu daban-daban fiye da +8 dBu. Mafi kyawun bayani a cikin wannan yanayin na iya zama daidaita madaidaitan tashoshin OMNEO (Dante-compatible) masu alaƙa don cimma matakan sauti na ƙima na -20 dBFS akan haɗin haɗin Dante transmitter (fitarwa) da tashoshi mai karɓa (shigarwa). Samar da matakan nunin sauti na dijital masu jituwa zai haifar da mafi kyawun aiki na Model 545DC da na'urorin masu amfani da layin ƙungiya masu alaƙa.

Matakan Audio da Ƙare Layin Jam'iyya

Biyu Daga mita suna nuna matakan siginar sauti da ke fitowa daga tashoshi biyu masu alaƙa da Model 545DC's party-line intercom channels A da B. Waɗannan siginar analog ɗin ana canza su zuwa dijital sannan kuma suna fitarwa akan tashoshi na Dante transmitter (fitarwa). da'irar intercom na layi mai alaƙa da Model 545DC don aiki daidai, rashin ƙarfi (juriya ga siginar AC kamar sauti) dole ne ya zama kusan 200 ohms.
Yawanci, don cimma wannan ya dogara da kayan aiki guda ɗaya wanda ke samar da ƙarewar sauti ɗaya a kowane tashar intercom. Wannan ƙarewa, 200 ohms na ƙima, ana yin kusan koyaushe a tushen samar da wutar lantarki ta intercom. (Nau'in samar da wutar lantarki na intercom yawanci yana ba da wutar lantarki ta DC da cibiyar sadarwa ta ƙarewa.)

Wani batu na iya tasowa idan siginar mai jiwuwa ta fito daga da'irar intercom-line jam'iyya da aka haɗa ko na'urorin masu amfani
ba a isa matakin da za a iya kaiwa ga matakan nuni na al'ada ba. Yana yiwuwa wata na'ura, kamar na'ura mai ba da wutar lantarki ta biyu a kan layin intercom na jam'iyya ɗaya, na iya haifar da yanayin "ƙashewa biyu". Wannan zai haifar da lalacewar tashar intercom na layi na jam'iyya na kusan 100 ohms (maɓuɓɓuka biyu, kowane 200 ohms, haɗin da ba daidai ba) wanda zai haifar da babbar matsala.
Matsalolin da ta fi fitowa fili ita ce matakan jiwuwar sauti na tashar intercom na iya ragewa (saukar da kai) da kusan 6 dB (rabin juzu'in sauti.tage). Bugu da kari, auto null da'irori, kamar samar da Model 545DC, ba za su iya samun mai kyau rabuwa (nulling) yi. Cire ƙarewar na biyu maras so (na biyu impedance na 200 ohms) shine kawai ingantacciyar hanyar kawar da matsalolin.

A mafi yawan lokuta, batun ƙarewa sau biyu zai zama mai sauƙi don warwarewa. A matsayin exampHar ila yau, yana yiwuwa ɗayan tushen wutar lantarki na Model 545DC, wanda ke ba da ƙarfin DC da ƙarewar ohms 200, an kunna shi da gangan lokacin da Model 545DC ke haɗa zuwa da'irar layi na waje da ƙare. Wannan ba daidai ba ne, yana haifar da yanayin "ƙarewa sau biyu". Kashe tushen wutar lantarki na gida na Model 545DC ta latsawa da riƙe maɓallin cirewa ta atomatik ko amfani da aikace-aikacen software na mai sarrafa ST shine duk abin da ake buƙata.

Wasu raka'o'in samar da wutar lantarki na intercom suna ba da damar zaɓin ƙarancin ƙarewa ya zama 200 ko 400 ohms.
Ana haɗa wannan ƙarfin sau da yawa a cikin madaidaicin matsayi 3 wanda kuma ba zai ba da damar yin amfani da ƙarancin ƙarewa ba. Tabbatar cewa saitin sauyawa da aka zaɓa, da kuma saituna da tura wasu kayan aikin da aka haɗa, suna haifar da rashin daidaituwar da'ira na 200 na kowane ɗayan tashoshin tashoshi guda biyu.

Matsayin Ƙarfin Ido

Ledojin koren LED guda biyu suna gefen hagu na gaban panel kuma suna da alaƙa da ikon aiki. Alamar PoE LED za ta yi haske a duk lokacin da aka haɗa haɗin Ethernet tare da damar Power-over-Ethernet (PoE). Wutar wutar lantarki ta DC zata yi haske a duk lokacin da DC voltage an yi amfani da shi. Matsakaicin yarda shine 10 zuwa 18 volts DC. Idan duka hanyoyin wutar lantarki suna nan duka LEDs za su yi haske, duk da haka tushen PoE ne kawai zai samar da ikon aiki na Model 545DC.

Zaɓin Yanayin Aiki-Layin Jam'iyya

Kamar yadda aka tattauna a baya, kowane ɗayan layin layin jam'iyya mai tashoshi guda biyu yana ba da yanayin aiki guda biyu. Ana amfani da yanayi ɗaya lokacin da ake buƙatar Model 545DC don ƙirƙirar da'irar layi ta jam'iyya, tana ba da 28 volts DC da cibiyar sadarwa ta ƙarewar ohms 200. A wannan yanayin, ana iya tallafawa na'urorin masu amfani kamar fakitin bel kai tsaye. Matsayin Ƙarfin Gida mai alaƙa LED zai haskaka kore lokacin da aka zaɓi wannan yanayin. Maɓallin kama-da-wane (tushen-software) wanda ke ɓangaren aikace-aikacen mai sarrafa ST zai nuna rubutun Kunna don nuna cewa an kunna wutar gida. Yanayin na biyu yana ba da damar Model 545DC don haɗawa zuwa da'irar layi na layi na jam'iyya guda ɗaya wanda ke ba da ƙarfin DC da 200 ohms na ƙarewa impedance. A cikin wannan yanayin, naúrar za ta yi aiki daidai da na'urar mai amfani kuma ba za a kunna LED Matsayin Wutar Wuta ba. A cikin wannan yanayin, Rubutun Kashe za a nuna shi a cikin maɓallin turawa mai kama da mai sarrafawa.

Don canza yanayin aikin mu'amalar layin jam'iyya abu ne mai sauƙi, kawai yana buƙatar maɓallan maɓallin turawa na atomatik mai alaƙa da za a danna kuma a riƙe shi na ɗan daƙiƙa biyu. Wannan zai sa yanayin aiki na Model 545DC ya canza ("juyawa") daga wannan yanayin zuwa wancan. Yayin da yanayin ke canzawa, madaidaicin Matsayin Wutar Gida mai alaƙa LED da aikace-aikacen mai sarrafa ST za su nuna daidai. Da zarar yanayin ya canza za a iya sake kunna maɓallin turawa. Hakanan za'a iya zaɓar yanayin aiki ta amfani da maɓallin turawa na kama-da-wane a cikin aikace-aikacen software mai sarrafa ST. Yanayin aiki da aka zaɓa za a adana shi a cikin ƙwaƙwalwar ajiyar da ba ta da ƙarfi, yana tabbatar da cewa zai dawo zuwa waccan ƙimar bayan sake zagayowar saukar da wutar lantarki.

Aiki Yanayin Wutar Wuta

Lokacin da Model 545DC's na gida ikon yanayin da aka kunna don intercom kewaye, naúrar za ta samar da DC ikon da 200 ohms impedance don ƙirƙirar "misali" guda-tashar jam'iyyar-line intercom kewaye. Matsakaicin layin jam'iyya zai samar da 28 volts DC akan fil 2 na masu haɗin XLR 3-pin tare da matsakaicin zane na yanzu na 150mA akwai. Wannan halin yanzu ya isa ya kunna na'urorin masu amfani da intercom daban-daban kamar ƙananan tashoshi masu amfani da fakitin bel. Aikace-aikacen watsa shirye-shirye na gama gari na iya amfani da Clear-Com RS-501 ko RS-701 fakitin bel. Zaɓi na'urorin da aka haɗa domin jimlar iyakar halin yanzu kada ta wuce 150mA. Wannan ba koyaushe shine mafi sauƙin adadi ba amma a web bincike gabaɗaya zai nemo ƙayyadaddun bayanai don duk na'urorin da aka saba amfani da su. Domin misaliample, bincike ya gano cewa RS-501 da ke ko'ina yana cinye iyakar 50 mA na halin yanzu. Dangane da wannan adadi, ana iya haɗa har zuwa uku daga cikin waɗannan raka'a zuwa Model 545DC. Sabuwar RS-701 tana da matsakaicin halin yanzu na 12mA da matsakaicin matsakaicin 23mA. Daga wannan bayanin ana iya kimanta cewa har zuwa biyar daga cikin waɗannan raka'a za a iya tallafawa cikin sauƙi.

Lokacin da yanayin wutar lantarki ya kunna, madaidaicin Matsayin LED mai alaƙa zai haskaka kore lokacin da ƙaramin adadin halin yanzu ke gudana daga da'irar layin jam'iyyar Model 545DC zuwa na'urar mai amfani da aka haɗa ko na'urori. Wannan kuma zai haifar da alaƙa mai kama da LED mai suna PL Active a cikin aikace-aikacen mai sarrafa ST zuwa haske kore. Wannan na yanzu, 5mA mara kyau, yana ba da siginar tushen wutar lantarki-layin jam'iyya zuwa firmware na Model 545DC yana nuna cewa ana yin aiki na yau da kullun. Firmware, bi da bi, zai haifar da Matsayin Active LED zuwa haske, aikace-aikacen mai sarrafa ST don haskaka LED ɗin sa na yau da kullun, da tashar mai watsawa ta Dante (fitarwa) ta kasance cikin yanayin aiki (wanda ba a saka). (Ta hanyar ɓata tashar watsawa ta Dante (fitarwa) lokacin da kewayar intercom ba ta aiki da siginar sauti maras so za a hana shi wucewa zuwa duniyar waje lokacin da ba a haɗa na'urar layin jam'iyya ba.)

Lura cewa saiti a cikin aikace-aikacen mai sarrafa ST na iya kashe buƙatun cewa zana na yanzu na 5 mA (na ƙima) ko mafi girma akan fil 2 na haɗin layin jam'iyya-XLR ana buƙata don Matsayin Active LED zuwa haske, mai kama da LED a cikin Aikace-aikacen mai sarrafa ST zuwa haske kore, da kuma hanyar sauti mai watsawa (fitarwa) don aiki. Ana kiran wannan aikin PL Active Detection kuma kashe shi zai iya dacewa da aikace-aikace na musamman. Koma zuwa sashin Kanfigareshan Model 545DC don cikakkun bayanai game da wannan aikin da yadda za'a iya amfani da shi.

Model 545DC's biyu-line intercom samar da wutar lantarki da'irori aiki a karkashin firmware iko. Wannan yana ba da damar gano yanayin kuskure kuma yana kare kewayen naúrar. Bayan fara kunna wutar lantarki ta layin jam'iyya ba a sanya ido kan fitarwar wutar lantarkin na tsawon daƙiƙa uku ba. Wannan yana ba da damar da'ira mai ba da wutar lantarki ta Model 545DC da na'urar mai amfani ta intercom ko na'urori don daidaitawa. Matsayin Wutar Wutar Gida mai alaƙa da LED za a haskaka ta da ƙarfi kuma maɓallin turawa na kama-da-wane a cikin aikace-aikacen mai sarrafa ST zai nuna Kunnawa rubutu. Matsayin Active LED, wanda ke amsa matsayin DC voltage a kan fil 2 na mai haɗin XLR mai 3-pin na layin jam'iyya, zai yi haske don nuna cewa fitarwar tana aiki. PL Active kama-da-wane LED a cikin mai sarrafa ST zai haskaka kore. Bayan wannan jinkirin farko, saka idanu yana aiki. Ana gano yanayin kuskure idan voltage akan fil 2 ya faɗi ƙasa da 24 don ci gaba da tazarar daƙiƙa 1. Firmware yana amsa wannan yanayin ta ɗan lokaci kaɗan don kashe tushen wutar lantarki na DC zuwa fil 2. Hakanan, azaman gargaɗi, zai kunna LED matsayi mai alaƙa da filashi mai kama da LED a cikin mai sarrafa ST. Bayan tazarar "sanyi-ƙasa" na 5-na biyu fitarwa na DC zai dawo daidai da yanayin da aka kunna na farko; Ana sake amfani da wuta zuwa fil 2, Matsayin Active LED zai haskaka, PL Active LED mai kama da wuta zai haskaka kore, kuma saka idanu ba zai fara ba na tsawon daƙiƙa uku. Cikakken yanayin gajeriyar kewayawa da aka yi amfani da da'irar samar da wutar lantarki ta jam'iyya zai haifar da ci gaba da zagayowar na daƙiƙa huɗu akan (daƙiƙa uku don farawa da daƙiƙa ɗaya don ganowa) sannan a kashe daƙiƙa biyar.

Aiki na Waje na Jam'iyyar-Layi

Lokacin da Matsayin Matsayin Wuta na Gida a gaban panel ɗin ba a kunna ba kuma ana yiwa maballin turawa ta atomatik a cikin mai sarrafa ST Lakabi Kashe layin layin jam'iyyar Model 545DC baya samar da wutar DC akan XLR fil 2 kuma yana ba da 200 ohms ƙarewa akan XLR fil 3. A wannan yanayin, Model 545DC ana nufin haɗa shi zuwa da'ira-layi mai ƙarfi na waje. Dole ne wannan da'irar-layin jam'iyya ta samar da wutar lantarki da ƙarewar da ake buƙata don ƙirƙirar da'irar intercom-line jam'iyya. A cikin wannan yanayin, Model 545DC yana aiki kawai a cikin salo iri ɗaya kamar na wata na'ura mai amfani da tashoshi ɗaya da aka haɗa. (A sakamakon haka, Model 545DC zai sami halayen fasaha na na'urar mai amfani mara ƙarfi.) Lokacin da aka haɗa zuwa da'irar layin jam'iyya mai ƙarfi Model 545DC's Active status LED zai haskaka lokacin da kusan 18 volts DC ko mafi girma ya kasance akan fil 2 na mai haɗin XLR mai alaƙa. Bugu da kari, STcontroller's PL Active kama-da-wane LED zai haskaka kore.
Lokacin da aka gano wannan yanayin, ana sanya tashar watsawar Dante mai alaƙa (fitarwa) a cikin yanayin aiki (wanda ba a kashe ba). In ba haka ba, an kashe (batattu) don kiyaye ingantaccen aikin Model 545DC.

Kamar yadda aka bayyana a baya, saiti a cikin aikace-aikacen mai sarrafa ST na iya kashe buƙatun cewa 18 volts DC ko mafi girma ya kasance akan fil 2 na haɗin layin XLR na jam'iyyar don Matsayin Active LED zuwa haske, thePL Active Virtual LED zuwa haske kore, da hanyar sauti mai watsawa (fitarwa) don zama mai aiki. Ana kiran wannan aikin PL Active Detection aikin kuma kashe shi zai iya dacewa da aikace-aikace na musamman. Koma zuwa sashin Kanfigareshan Model 545DC don cikakkun bayanai game da wannan aikin da yadda za'a iya amfani da shi.

Auto Null

Model 545DC yana ƙunshe da kewayawa don lalata hanyar sadarwar matasan da ke da alaƙa da kowane haɗin layin jam'iyya ta atomatik. Wannan hanya tana raba siginar mai jiwuwa yayin da ake aika su kuma ana karɓar su daga tashoshi mai jiwuwa da ke da alaƙa da da'irar intercom-line-party. Ana ba da maɓallan turawa guda biyu, waɗanda ke kan gaban panel, don kunna ayyukan ɓoyayyiyar atomatik, ɗaya don kowane tashoshi. Maɓallai na gani ("laushi") a cikin aikace-aikacen software mai sarrafa ST kuma suna ba da damar kunna ayyukan ɓoyayyiyar atomatik. LEDs matsayi guda biyu, waɗanda ke kan gaban gaban naúrar, da LEDs guda biyu na kama-da-wane (tushen zane-zane) da aka samar a cikin mai sarrafa ST suna ba da nuni ga ayyukan da'irori na atomatik.

Don fara null ta atomatik don kewayawa da farko yana buƙatar hasken LED mai alaƙa da ke aiki. Lokacin da aka saita yanayin aiki don wutar gida matsayin Active LED zai haskaka lokacin da mafi ƙarancin adadin halin yanzu da ake buƙata yana gudana daga wutar lantarki ta ciki. A madadin, lokacin da ba a kunna LED Power na gida ba dole ne a kunna matsayin Active LED, yana nuna cewa isasshe DC vol.tage yana nan akan fil 2 na da'irar layin jam'iyyar da aka haɗa. Da zarar an kunna matsayin Active LED, fara aikin banza kawai yana buƙatar latsawa da sakewa (“taɓawa”) maɓallin null na gaba-gaba. A madadin, maɓallin kama-da-wane a cikin aikace-aikacen mai sarrafa ST ana iya amfani da shi don fara ɓarna ta atomatik. Tsarin cirewa ta atomatik yana ɗaukar kusan daƙiƙa 10 don kammalawa. LEDs a gaban panel ɗin naúrar suna ba da alamar gani na tsarin ɓoyayyiyar atomatik, mai walƙiya orange lokacin da tsarin lalata auto ke aiki. LEDs na gani a cikin aikace-aikacen mai sarrafa ST suna ba da aiki iri ɗaya. Ana yi musu lakabin Ch A (Pin 3) da Ch B (Pin 3) don nuna kai tsaye wanda aikin ɓoyayyiyar atomatik ke aiki.

Idan an danna maɓallin null ta atomatik, ko dai a gaban panel ko a cikin mai sarrafa ST, lokacin da ba a kunna matsayin Active LED ba, tsarin lalata auto ba zai fara ba. Fitilar null ta atomatik za ta yi saurin walƙiya orange sau huɗu don nuna wannan yanayin.

A al'ada, ana aiwatar da tsarin rushewa a lokacin daidaitawar Model 545DC na farko amma babu wani dalili da zai sa ba za a iya fara shi ba kowane lokacin da mutum yake so.
Iyakar lokacin da dole ne a yi watsi da atomatik shine idan yanayi sun canza tare da na'urorin mai amfani da layin jam'iyya da wayoyi da aka haɗa zuwa mai haɗin layin jam'iyyar Model 545DC. Ko da ɗan ƙaramin canji zuwa da'ira-line intercom, kamar ƙara ko cire wani sashe na kebul, na iya isa ya ba da garantin cewa za a aiwatar da tsarin lalata ta atomatik.

Matsakaicin ɓarna ta atomatik yana farawa tare da ɓata mai karɓar Dante (shigarwa) da Dante transmitter (fitarwa) hanyoyin siginar sauti. Idan Model 545DC yana ba da iko akan haɗin layin jam'iyya, wannan yana biye da gajeriyar hanyar cire haɗin (hutu) a cikin 28 volts DC wanda aka aika zuwa fil 2. Wannan zai kashe makirufo akan waɗancan na'urorin masu amfani da aka haɗa waɗanda suka dace da Clear-Com “mic kill” yarjejeniya. Ana aiwatar da ainihin tsarin kawar da kai na gaba. Za a ba da jerin sautunan sautuna zuwa haɗin layin jam'iyya. Sauran Model 545DC kewaye, ƙarƙashin sarrafa firmware, za su yi gyare-gyare cikin sauri don cimma mafi kyawun ɓarna mai yuwuwa. Bayan gyare-gyaren da aka yi ana adana sakamakon a cikin Ƙwararren Ƙwararren Ƙwararren Ƙwararren Ƙwararren 545DC. Da zarar aikin ya cika, ana sake kunna mai karɓar Dante (shigarwa) da Dante transmitter (fitarwa) hanyoyin sauti.

Idan za ta yiwu, kafin yin lalata ta atomatik yana da kyau a faɗakar da duk ma'aikatan da ke amfani da na'urorin intercom na layin jam'iyya da ke da alaƙa. Sautunan da aka aika zuwa da'irar-layin jam'iyya yayin aikin cin zarafi ba su da ƙarfi sosai ko abin ban tsoro, amma yawancin masu amfani za su so su cire naúrar kai yayin aiwatarwa. Baya ga gargaɗin masu amfani, yana iya zama lokaci mai kyau don tambayar su su kashe duk wani makirifo mai aiki. Yayin da siginar "mic kisa" ta atomatik zai dace da yawancin na'urorin masu amfani bazai shafi kowa ba. Rufe makirufo yana da mahimmanci, saboda samun "zurfin" null yana buƙatar cewa babu sigina na waje ya kasance a cikin da'irar intercom.

Kira Tallafin Haske

Model 545DC yana ba da aikin goyan bayan haske na kira, yana ƙyale voltage hade da aikin hasken kira akan Model 545DC mai haɗin na'urorin mai amfani don aiki tare a aikace-aikacen haɗin gwiwar Dante. Hakanan aikin yana ba da damar Model 545DC don haɗin kai tare da Model 545DR Intercom Interface Unit da goyan bayan ayyukan hasken kiran tsaka-tsakin. Wannan yana ba da damar dacewa da hasken kira tsakanin tashoshi ɗaya mai kunna hasken kira na DC da fitilun kira mai ƙarfi na tashoshi 2. Ba a buƙatar aikin afareta don ayyukan goyan bayan hasken kira don aiwatar da ayyukansu.

Aikin goyan bayan hasken kira yana da ban sha'awa sosai. An aiwatar da shi a cikin software, yana ba da damar DC voltage an gano shi akan fil 3 na haɗin layin jam'iyya don haifar da siginar siginar siginar sine na 20 kHz da aka ƙirƙira ta lambobi akan tashar watsawar Dante (fitarwa). Sigina mai girma (wanda aka sani da 20 kHz) da aka karɓa akan tashar mai karɓar Dante (shigarwa) zai haifar da Model 545DC's circuitry yana fitar da DC vol.tage akan fil 3 na haɗin haɗin layin jam'iyya. Matsalolin ƙaramar wucewa (LP) da aka aiwatar da dijital ta hana manyan sautunan mitoci wucewa ta hanyar da'ira mai jiwuwa.

Zaɓi a cikin aikace-aikacen mai sarrafa ST yana ba da damar kashe goyan bayan hasken kira. A fasaha, wannan yana ba da umarnin firmware na naúrar (software mai haɗawa) don kada ya samar da sautin 20 kHz lokacin da aka gano DC akan fil 3. Hakanan yana hana DC vol.tage daga aika zuwa fil 3 lokacin da ake karɓar sautin "kira" mai girma. Tace siginar babban mitoci (ta amfani da matattarar ƙarancin wucewa) koyaushe zai kasance yana aiki. Kashe tallafin hasken kira zai dace kawai a cikin ƙa'idodi na musamman.

USB Interface

Nau'in USB A rumbun ajiya da matsayi mai alaƙa LED, mai lakabin Sabuntawar Firmware, suna kan ɓangaren baya na Model 545DC. Ana amfani da wannan kebul na mai masaukin baki ne kawai don sabunta firmware na naúrar; babu bayanan sauti kowane iri da zai wuce ta cikinsa. Don cikakkun bayanai kan tsarin sabuntawa don Allah koma zuwa sashin Bayanan fasaha.

Bayanan fasaha Kira Tallafin Haske

Alamar "kira" ko "hasken kira" akan da'irar layi na layi na Clear-Com ana watsa shi ta hanyar DC vol.tage wanda ake amfani da shi zuwa hanyar sauti, wanda yawanci fil 3 ne na kebul na haɗin kai. Wannan DC voltage ana tarawa (ƙara) ga duk wani sauti da yake halarta. Model 545DC yana gano lokacin da siginar hasken kira ke aiki ta hanyar lura da hanyar sauti don kasancewar DC vol.tage. Ana buƙatar sigina na kusan 5 volts DC ko mafi girma don nuna cewa aikin kira yana aiki. Model 545DC kuma na iya samar da siginar kira ta amfani da volt na DCtage zuwa hanyar sauti. Siginar DC, kusan 16 volts, shine dampsama da ƙasa don rage ƙarar dannawa ko buɗa zuwa siginar sauti.

Yayin da Model 545DC zai iya ganowa da samar da siginar kira, ba zai yiwu a aika da karɓar waɗannan siginar DC kai tsaye akan haɗin Dante ba saboda ainihin abin da aka yi niyya don jigilar sauti kawai. Model 545DC yana aiki a kusa da wannan batu ta hanyar canza siginar hasken kiran kira na DC zuwa wanda ya dogara da sautin 20 kHz. Mai amfani da basira zai gane wannan azaman hanyar kira da jerin TW ke amfani dashi daga RTS; maimakon sigina ta hanyar DC a cikin hanyar sauti, ana amfani da siginar 20 kHz. A cikin duniyar “telco” ana kiran wannan azaman siginar in-band, ba kamanceceniya da hanyar buga sautin taɓawa da ake amfani da ita akan layukan wayar analog ba.
Ba kamar siginar sautin taɓawa ba, siginar 20 kHz yana da advantage na kasancewa sama da kewayon ji na yawancin mutane. Wannan yana ba da damar sauti na intercom na al'ada da siginar kira 20 kHz suyi aiki lokaci guda. Kuma jigilar wannan haɗakar magana / siginar kira akan Model 545DC's Dante haɗin bai kamata ya zama matsala a matsayin ƙwararrun ƙwararrun watsa shirye-shiryen sauti na dijital da ke amfani da 48 kHz sampƘididdigar na iya ɗaukar siginar 20 kHz cikin sauƙi.

Lokacin da Model 545DC ya gano DC akan ɗayan hanyoyin mai jiwuwa (filin 3 na ko dai na masu haɗin layin layi na baya-baya) zai samar da sautin 20 kHz a cikin lambobi kuma ya haɗu ( jimla) tare da kowane siginar sauti da aka gabatar akan haɗin gwiwa. Dante transmitter (fitarwa) tashar.
Da'irar ganowa a cikin Model 545DC's Dante mai karɓar (shigarwa) hanyoyin sauti na ci gaba da saka idanu don kasancewar sautin 20 kHz. Idan an gano wannan siginar (a cikin yankin dijital) zai haifar da volt na DCtage da za a yi amfani da shi zuwa hanyar sauti na da'irar mu'amala da layin jam'iyya mai alaƙa. Lokacin da siginar 20 kHz ya daina kasancewa da DC voltage za a cire. Aikin fassarar 20 kHz-zuwa-DC yana faruwa ta atomatik ba tare da wani tsari da ake buƙata ba. Wannan hanya tana da amfani sosai saboda dalilai da yawa. Yana ba da damar nau'ikan Model 545DC guda biyu waɗanda ke haɗin haɗin kai ta hanya-zuwa-aya don jigilar sauti da siginar kira tsakanin su. Hakanan zai ba da damar goyan bayan siginar kira tsakanin Model 545DC (mai tallafawa da'irorin layin jam'iyyar Clear Com guda biyu) da Model 545DR (mai goyan bayan da'irar layin jam'iyyar RTS 2). Kuma a ƙarshe, zai ba da damar kayan aiki waɗanda ke da ikon jigilar siginar kira na 20 kHz waɗanda ke da alaƙa da da'irar layin jam'iyyar RTS, kamar tashoshin jiragen ruwa na RTS ADAM SOMEONE, don aikawa da karɓar siginar kira na tushen DC waɗanda ke da alaƙa da layin jam'iyyar Clear-Com guda ɗaya. na'urori.

Lura cewa masu tace dijital a cikin Model 545DC's firmware suna hana ainihin duk bayanan da ke sama da 10 kHz aika zuwa tashoshi masu jiwuwa na layin jam'iyya. Wannan yana taimakawa don tabbatar da cewa hanyoyin haɗin gwiwar suna samar da "zurfin" mara kyau kamar yadda yake kiyaye siginar kira na 20 kHz daga kowace hanyar sauti ta layin jam'iyya.

Dandalin gama gari

Model 545DC yana ba da musaya tsakanin layin jam'iyya-line mai zaman kansa guda biyu masu zaman kansu. Ana iya haɗa waɗannan musaya zuwa nau'ikan na'urorin masu amfani guda biyu, da'irori biyu na layi na jam'iyya, tashoshi biyu daga ma'aunin wutar lantarki na layin jam'iyya na waje, ko kowane haɗin gwiwa. Wani abu mai mahimmanci da za a tuna shi ne cewa tushen wutar lantarki da haɗin tashar sauti masu alaƙa da Model 545DC tashoshi guda biyu na layin mu'amalar jam'iyya-layi suna raba wuri ɗaya. Wannan kamar yadda ake tsammani amma yana ba da iyakancewar aikace-aikacen guda ɗaya. Ba a nufin hanyoyin haɗin kai guda biyu don haɗa haɗin kai (gada) da'irori biyu na intercom waɗanda ke ware da juna. Idan an yi haka ta hanyar haɗin haɗin fil 1 akan Model 545DC masu haɗin XLR guda biyu 3-pin mutum na iya tsammanin ƙirƙira hum, hayaniya, ko wasu kayan aikin sauti. Wannan zai zama sakamakon yuwuwar bambance-bambancen da yawanci za a iya samu akan da'irori biyu na layi na jam'iyya. Idan ana buƙatar wannan haɗin kai tare da aikin keɓewa samfur kamar Clear-Com TW-12C zai zama dole.

 Adireshin IP Adireshin

Ta hanyar tsohuwa, Model 545DC's Dante-associated Ethernet interface zai yi ƙoƙarin samun adireshin IP ta atomatik da saitunan haɗin gwiwa ta amfani da DHCP (Dynamic Host Configuration Protocol). Idan ba a gano uwar garken DHCP ba za a sanya adireshin IP ta atomatik ta amfani da hanyar haɗin kai-na gida. An san wannan ƙa'idar a cikin duniyar Microsoft® azaman Adireshin IP Mai Zaman Kanta (APIPA). Har ila yau, wani lokaci ana kiranta da auto-IP (PIPPA). Link-local zai sanya adireshin IP na musamman a cikin kewayon IPv4 na 169.254.0.1 zuwa 169.254.255.254. Ta wannan hanyar, ana iya haɗa na'urori masu kunna Dante da yawa tare kuma suna aiki ta atomatik, ko uwar garken DHCP yana aiki ko a'a akan LAN. Hatta na'urorin Dante guda biyu waɗanda ke da haɗin kai kai tsaye ta amfani da igiyar facin RJ45, a mafi yawan lokuta, za su sami adiresoshin IP daidai kuma su sami damar sadarwa tare da juna.

Togiya yana tasowa lokacin ƙoƙarin haɗa na'urorin Dante guda biyu kai tsaye waɗanda ke amfani da haɗaɗɗun da'irori na Ultimo don aiwatar da Dante. Model 545DC yana amfani da Ultimo X2 “guntu” kuma, don haka, haɗin kai tsaye ɗaya zuwa ɗaya tsakaninsa da wani samfurin tushen Ultimo galibi ba za a sami tallafi ba. Ana buƙatar canjin Ethernet mai haɗa waɗannan raka'a don samun nasarar haɗa na'urorin tushen Ultimo guda biyu. Dalilin fasaha da ake buƙatar sauyawa yana da alaƙa da buƙatar ɗan jinkiri (jinkiri) a cikin kwararar bayanai; Ethernet mai sauyawa zai samar da wannan. Wannan ba zai zama matsala ba kamar yadda Model 545DC ke amfani da Power-over Ethernet (PoE) don samar da ƙarfin aiki. Don haka, a mafi yawan lokuta za a yi amfani da canjin Ethernet mai kunna PoE don tallafawa Model 545DC raka'a.

Yin amfani da aikace-aikacen software na Dante Controller, adireshin IP na Model 545DC da sigogin cibiyar sadarwar da ke da alaƙa za a iya saita don daidaitawar jagora (daidaitacce ko a tsaye). Duk da yake wannan tsari ne wanda ya fi dacewa fiye da barin DHCP ko haɗin kai-na gida "yi abin nasu," idan kafaffen magana ya zama dole to wannan damar tana samuwa. A wannan yanayin, ana ba da shawarar sosai cewa kowace naúrar a yi alama a zahiri, misali, kai tsaye ta amfani da alamar dindindin ko “console tef,” tare da takamaiman adireshin IP ɗin sa. Idan sanin adireshin IP na Model 545DC ya ɓace babu maɓallin sake saiti ko wata hanya don mayar da naúrar cikin sauƙi zuwa saitunan IP na asali.

A cikin abin takaici cewa adireshin IP na na'urar ya “ɓace,” ana iya amfani da umarnin hanyar sadarwa na Resolution Protocol (ARP) don “bincike” na'urori akan hanyar sadarwa don wannan bayanin. Domin misaliampHar ila yau, a cikin Windows OS za a iya amfani da arp -a umurnin don nuna jerin bayanan LAN wanda ya haɗa da adireshin MAC da adiresoshin IP masu dacewa. Hanya mafi sauƙi na gano adireshin IP ɗin da ba a sani ba shine ƙirƙirar LAN "mini" tare da ƙaramin PoE-enabled Ethernet mai haɗa kwamfuta ta sirri zuwa Model 545DC. Sannan ta amfani da umarnin ARP da ya dace ana iya samun “alamu” da ake buƙata.

Inganta Ayyukan hanyar sadarwa

Don mafi kyawun aikin Dante audio-over-Ethernet ana ba da shawarar hanyar sadarwa da ke goyan bayan iyawar VoIP QoS. A cikin aikace-aikacen da ke amfani da zirga-zirgar zirga-zirgar Ethernet multicast da ke ba da damar IGMP snooping na iya zama mai mahimmanci. (A wannan yanayin, tabbatar da cewa goyan bayan saƙon lokaci na PTP yana nan.) Ana iya aiwatar da waɗannan ka'idoji akan kusan duk maɓallan Ethernet da aka sarrafa na zamani. Akwai ma maɓalli na musamman waɗanda aka inganta don aikace-aikacen da ke da alaƙa da nishaɗi. Koma zuwa ga Inordinate website (inordinate. com) don cikakkun bayanai kan inganta hanyoyin sadarwa don aikace-aikacen Dante.

Nunin Firmware Na Aikace-aikacen

Zaɓin a cikin aikace-aikacen software na mai sarrafa ST yana ba da damar gano sigar firmware na aikace-aikacen Model 545DC. Wannan na iya zama da amfani yayin aiki tare da ma'aikatan masana'anta akan tallafin aikace-aikacen da magance matsala. Don gano sigar firmware, fara da haɗa naúrar Model 545DC zuwa cibiyar sadarwa (ta hanyar Ethernet tare da PoE) kuma jira har sai naúrar ta fara aiki. Sa'an nan, bayan fara ST controller, sakeview Jerin na'urorin da aka gano kuma zaɓi takamaiman Model 545DC wanda kuke son tantance sigar firmware ɗin aikace-aikacen sa. Sannan zaɓi Shafin da Bayani a ƙarƙashin Na'ura shafin. Sannan shafi zai nuna wanda zai ba da bayanai masu amfani da yawa. Wannan ya haɗa da sigar firmware ɗin aikace-aikacen da kuma cikakkun bayanai akan firmware ɗin Dante interface.

Tsarin Sabunta Firmware na Aikace-aikace

Yana yiwuwa za a fitar da sabbin sigogin firmware na aikace-aikacen (software mai haɗawa) waɗanda ke amfani da na'urar haɗaɗɗiyar ƙirar ƙirar 545DC's micro controller (MCU) don ƙara fasali ko daidaitattun batutuwa. Koma zuwa Studio Technologies' webshafin don sabuwar manhajar aikace -aikace file. Naúrar tana da ikon ɗaukar nauyin da aka bita file A cikin ƙwaƙwalwar ajiyar MCU mara ƙarfi ta hanyar kebul na USB. Model 545DC yana aiwatar da aikin rundunar USB wanda ke goyan bayan haɗin kebul na filasha kai tsaye. Samfurin 545DC ku MCU tana sabunta firmware ta aikace-aikacen ta amfani da a file mai suna M545DCvXrXX.stm inda Xs ke da lambobi na goma waɗanda ke wakiltar ainihin lambar sigar firmware.

Tsarin sabuntawa yana farawa ta shirya kebul na filasha. Fil ɗin ba dole ba ne ya zama fanko (blak) amma dole ne ya kasance a cikin tsarin FAT32 na kai-komfuta. Kebul na USB a cikin Model 545DC ya dace da USB 2.0-, USB 3.0-, da USB 3.1 masu dacewa da filasha. Ajiye sabon firmware na aikace-aikacen file a cikin tushen directory na flash drive tare da sunan M545DCvXrXX.stm inda XrXX shine ainihin lambar sigar. Studio Technologies za su ba da firmware na aikace-aikacen file ciki na .zip archive file. Sunan zip file zai nuna aikace-aikacen file's version number kuma zai ƙunshi biyu files. Daya file zai zama ainihin aikace-aikacen file da sauran rubutu readme (.txt). file. Ana ba da shawarar cewa karantawa (.txt) file be reviewed kamar yadda zai ƙunshi cikakkun bayanai game da firmware aikace-aikacen da ke da alaƙa. Firmware na aikace-aikacen file cikin zip file zai bi yarjejeniyar suna.

Da zarar an shigar da kebul na filasha a cikin kebul na mai watsa shiri na USB, ta hanyar nau'in USB A ma'ajin da ke kan layin baya na Model 545DC, dole ne a kashe naúrar kuma a sake kunna shi. A wannan lokaci, da file daga kebul na flash ɗin zai yi lodi ta atomatik. Madaidaicin matakan da ake buƙata za a ba da haske a cikin sakin layi na gaba.

Don shigar da firmware ɗin aikace -aikacen file, bi waɗannan matakan:

1. Cire haɗin wuta daga Model 545DC. Wannan na iya haɗawa ko dai cire haɗin PoE Ethernet wanda aka yi zuwa jack RJ45 akan ɓangaren baya. A madadin, yana iya haɗawa da cire tushen 12 volts DC wanda aka haɗa zuwa mai haɗin XLR 4-pin, kuma wurin da ke bayan panel.
2. Saka kebul na filasha da aka shirya a cikin ma'ajin kebul na baya na naúrar.
3. Aiwatar da wutar lantarki zuwa Model 545DC ko dai ta haɗa siginar PoE Ethernet ko tushen 12 volts DC.
4. Bayan 'yan dakiku Model 545DC zai gudanar da shirin "boot loader" wanda zai loda sabon firmware ta atomatik. file ( M545DCvXrXX.stm ). Wannan aikin lodawa zai ɗauki 'yan daƙiƙa kaɗan kawai. A wannan lokacin koren LED wanda ke kusa da rumbun USB zai yi haske a hankali. Da zarar an gama ɗaukan aikin gabaɗaya, yana ɗaukar kusan daƙiƙa 10, Model 545DC zai sake farawa ta amfani da sabuwar firmware ɗin aikace-aikacen da aka ɗora.
5. A wannan lokacin, Model 545DC yana aiki tare da sabuwar firmware aikace-aikacen da aka ɗora kuma ana iya cire kebul na filasha. Amma don zama mai ra'ayin mazan jiya, cire haɗin PoE Ethernet ko tushen wutar lantarki na 12 volts da farko sannan cire kebul na filasha. Sake haɗa haɗin PoE Ethernet ko tushen wutar lantarki 12 volts DC don sake kunna naúrar.
6. Yin amfani da mai sarrafa ST, tabbatar da cewa an ɗora sigar firmware ɗin aikace-aikacen da ake so daidai.

Lura cewa idan ana amfani da wutar lantarki zuwa Model 545DC idan na'urar filasha ta USB da aka haɗa ba ta da daidai file (M545DCvXrXX.stm) a cikin tushen fayil ɗinsa babu wani lahani da zai faru. Bayan kunna koren LED ɗin, wanda ke kusa da ma'aunin USB a bangon baya, zai kunna da kashewa cikin sauri na ƴan daƙiƙa don nuna wannan yanayin sannan aiki na yau da kullun ta amfani da firmware ɗin aikace-aikacen naúrar da ke akwai.

Ultimo Firmware Sabunta

Kamar yadda aka tattauna a baya, Model 545DC yana aiwatar da haɗin gwiwar Dante ta amfani da haɗin haɗin Ultimo daga Inordinate. Ana iya amfani da mai sarrafa ST ko aikace-aikacen software na Dante Controller don tantance sigar firmware (software da aka haɗa) da ke zaune a cikin wannan haɗaɗɗiyar da'ira. Ana iya sabunta firmware (software ɗin da aka haɗa) da ke zaune a cikin UltimoX2 ta hanyar tashar tashar Ethernet ta Model 545DC. Ana aiwatar da tsarin ɗaukakawa cikin sauƙi ta amfani da hanyar sarrafa kai da ake kira Dante Updater wanda ke kunshe a matsayin wani ɓangare na aikace-aikacen Dante Controller. Ana samun wannan aikace-aikacen, kyauta, daga Audinate website (audinate. com). Sabbin Model 545DC firmware file, tare da suna a cikin nau'i na M545DCvXrXrX.dnt, yana samuwa a kan Studio Technologies' webrukunin yanar gizo da kuma kasancewa ɓangare na bayanan ɗakunan karatu na samfuran Ordinate. Ƙarshen yana ba da damar aikace-aikacen software na Dante Updater wanda aka haɗa tare da Dante Controller don yin tambaya ta atomatik kuma, idan an buƙata, sabunta Model 545DC's Dante interface.

Maido da Tsoffin Factory

Umurni a cikin aikace-aikacen software na mai sarrafa ST yana ba da damar sake saita kuskuren Model 545DC zuwa ƙimar masana'anta. Daga STcontroller zaži Model 545DC wanda kake son dawo da abubuwan da basu dace ba. Zaɓi shafin na'ura sannan kuma zaɓin Factory Defaults. Sannan danna kan akwatin Ok. Koma zuwa Karin Bayani A don jerin ɓangarorin ƙirar masana'anta na Model 545DC.

Ƙayyadaddun bayanai

Tushen wutar lantarki:
Power-over-Ethernet (PoE): class 3 (tsakiyar iko) kowane IEEE® 802.3af
Na waje: 10 zuwa 18 volts DC, 1.0 A max a 12 volts DC

Hanyar Sadarwa ta Hanyar Sadarwa:
Nau'in: Dante audio-over-Ethernet
Taimakon AES67-2018: eh, ana iya kunnawa/kashewa
Taimakawa Manajan Domain Dante (DDM): iya
Zurfin Bit: har zuwa 24
Sampku Rate: 48 kHz
Tashoshin watsawa na Dante (Fitarwa): 2
Tashoshin Mai karɓar Dante (Input): 2
Dante Audio yana gudana: 4; 2 watsawa, 2 mai karɓa
Analog zuwa Daidaitan Dijital: a -10 dBu siginar analog akan tashar tashar keɓaɓɓiyar layin jam'iyya a cikin matakin fitarwa na dijital na Dante na -20 dBFS da mataimakin versa.

Interface Interface:
Nau'in: 100BASE-TX, Fast Ethernet da IEEE 802.3u (10BASE-T da 1000BASE-T (GigE) ba a tallafawa)
Power-over-Ethernet (PoE): Ta IEEE 802.3af
Yawan Bayanai: 100 Mb/s (10 Mb/s da 1000 Mb/s ba a tallafawa)

Gabaɗaya Audio:
Martanin Mitar (PL zuwa Dante): -0.3 dB @ 100 Hz (-4.8 dB @ 20 Hz), -2 dB @ 8 kHz (-2.6 dB @ 10 kHz)
Martanin Mitar (Dante zuwa PL): -3.3 dB @ 100 Hz (-19 dB @ 20 Hz), -3.9 dB @ 8 kHz (-5.8 dB @ 10 kHz)
Karya (THD+N): <0.15%, an auna a 1 kHz, shigar da Dante zuwa PL interface fil 2 (0.01% fil 3)
Alamar siginar-zuwa-Noise Ratio: > 65 dB, A-nauyi, aunawa a 1 kHz, shigar da Dante zuwa PL interface fil 2 (73 dB, PL interface fil 3)

Hanyoyin Sadarwar Sadarwar Jam'iyyar-Layi (PL): 2
Nau'in: Analog na tashar tashar guda ɗaya PL (XLR fil 1 gama gari; XLR fil 2 DC; XLR fil 3 audio mara daidaituwa)
Daidaituwa: Tsarukan intercom na PL guda-tashar kamar waɗanda Clear-Com® ke bayarwa
Tushen wutar lantarki, XLR Pin 2: 28 volts DC, 150mA matsakaita Impedance, XLR Pin 3 - Ƙarfin PL na gida
An kunna:> 10k ohms
Impedance, XLR Pin 3 - Ƙarfin PL na Gida: 200 ohms
Analog Audio Level, XLR Pin 3: -14 dBu, maras muhimmanci, +7 dBu mafi girma
Tallafin Siginar Haske na Kira, XLR Pin 3: DC voltage a kan fil 3; ganowa a>= 5 5 volts DC maras kyau; Yana haifarwa a 16 volts DC mai suna Mic Kill Support Signal Support, XLR Pin 2 - Ƙarfin Gida
An kunna: hutu na ɗan lokaci a cikin DC voltage
Layin Jam'iyyar (PL) Haɓaka: 2
Topology: 3-section analog circuitry rama domin resistive, inductive, da capacitive lodi
Hanyar Rushewa: atomatik akan ƙaddamar da mai amfani, na'ura mai sarrafawa yana aiwatar da sarrafa dijital na kewayen analog; saituna da aka adana a cikin ƙwaƙwalwar mara mara ƙarfi
Rage Line Impedance Range: 120 zuwa 350 ohms
Tsawon Tsayin Kebul: 0 zuwa 3500 ƙafa
Asarar Trans-Hybrid: > 55 dB, yawanci a 800 Hz
Mitaku: 4
Aiki: yana nuna matakin shigar da sauti da tashoshin fitarwa
Nau'in: 5-segment LED, gyaggyarawa VU ballistics

Masu haɗawa:
Layin Jam'iyyar (PL) Intercom: biyu, 3-pin namiji XLR
Ethernet: Neutrik etherCON RJ45 jack
DC na waje: 4-pin namiji XLR
USB: rubuta A receptacle (amfani da kawai don sabunta aikace-aikace firmware)
Tsari: yana buƙatar aikace-aikacen software na STcontroller Studio Technologies
Ɗaukaka Software: Kebul na USB da aka yi amfani da shi don sabunta firmware aikace-aikace; Aikace-aikacen Dante Updater da aka yi amfani da shi don haɓaka firmware na Dante interface

Muhalli:
Yanayin Aiki: 0 zuwa 50 C (32 zuwa 122 F)
Yanayin Ajiya: -40 zuwa 70 C (-40 zuwa 158 digiri F)
Danshi: 0 zuwa 95%, wanda ba a haɗa shi ba
Matsayi: ba halin

Girma - Gabaɗaya:
8.70 inci fadi (22.1 cm)
1.72 inci tsayi (4.4 cm)
8.30 inci zurfi (21.1 cm)
Nauyi: 1.7 fam (0.77 kg); Na'urorin shigarwa masu hawa rak suna ƙara kusan fam 0.2 (0.09 kg)
Aiki: yi nufin aikace-aikacen tebur.
Akwai kuma kayan hawa na zaɓi huɗu:
RMBK-10 yana ba da damar sanya raka'a ɗaya a cikin yankan panel ko a saman fili
RMBK-11 yana ba da damar hawa raka'a ɗaya a gefen hagu ko dama na sarari ɗaya (1U) na ma'auni mai inci 19.
RMBK-12 yana ba da damar hawa raka'a biyu a cikin sarari ɗaya (1U) na ma'auni mai girman inci 19
RMBK-13 yana ba da damar hawa raka'a ɗaya a tsakiyar sarari ɗaya (1U) na daidaitaccen rak ɗin inci 19.
Zaɓin Samar da Wuta na DC: Studio Technologies'PS-DC-02 (100-240 V, 50/60 Hz, shigarwar; 12 volts DC, 1.5 A, fitarwa), sayayya daban

Ƙayyadaddun bayanai da bayanan da ke ƙunshe a cikin wannan Jagorar mai amfanin batun canzawa ba tare da sanarwa ba.

Karin Bayani A-ST Mai Gudanarwa Tsoffin Ƙimar Kanfigareshan

Tsarin - Taimakon Hasken Kira: Kunna
Tsarin - PL Gane Mai Aiki: On

Shafi B– Bayanin Zane na Kit ɗin Shigarwa don Yanke Panel ko Amfani da Haƙuri (Lambar oda: RMBK-10)
Ana amfani da wannan kayan shigarwa don hawan Model 545DC naúrar guda ɗaya a cikin yankan panel ko saman fili.

Shafi C– Bayanin Zane na Kit ɗin Shigar Rack-Hagu ko Gefen Dama don Rukunin “1/2-Rack” ɗaya (Lambar oda: RMBK-11)
Ana amfani da wannan kayan shigarwa don hawan Model 545DC naúrar ɗaya zuwa sarari ɗaya (1U) na rakiyar kayan aiki mai inci 19. Ƙungiyar za ta kasance a gefen hagu- ko dama na buɗewar 1U.

Shafi D– Bayanin Zane na Kit ɗin Sanya Dutsen Rack don Raka'a "1/2-Rack" Biyu (Lambar oda: RMBK-12)
Ana iya amfani da wannan kayan shigarwa don hawan Model 545DC raka'a biyu ko Model 545DC naúrar ɗaya da wani samfurin da ya dace da RMBK-12 (kamar Studio Technologies' Model 5421 Dante Intercom Audio Engine) cikin sarari ɗaya (1U) na 19-inch kayan aiki tara.

Shafi E– Bayanin Zane na Kit ɗin Shigar Dutsen Cibiyar Rack-Mount don Rukunin “1/2-Rack” ɗaya (Lambar oda: RMBK-13)
Ana amfani da wannan kayan shigarwa don hawan Model 545DC naúrar ɗaya zuwa sarari ɗaya (1U) na rakiyar kayan aiki mai inci 19. Ƙungiyar za ta kasance a tsakiyar buɗewar 1U.

Haƙƙin mallaka © 2024 ta Studio Technologies, Inc., duk haƙƙin mallaka  studio-tech.com

Takardu / Albarkatu

Studio Technologies 545DC Intercom Intercom [pdf] Jagorar mai amfani 545DC Intercom Interface, 545DC, Intercom Interface, Interface

Magana

• Manual mai amfani