KAYAN KASA SCXI-1129 Matrix Canja Module

Bayanin samfur

Samfurin da ake magana a kai a cikin littafin mai amfani shine SCXI-1129 Terminal Block don NI SCXI-1337. Abu ne da ake amfani dashi don haɗa sigina a cikin tsarin aunawa. An ƙera toshe tasha don a yi amfani da shi tare da SCXI chassis da SCXI-1129 sauya module. Yana da mahimmanci a bi umarnin da aka bayar don tabbatar da ingantaccen shigarwa da amfani da toshewar tasha.

Umarnin Amfani da samfur

Cire Tushen Tasha:

Don guje wa lalacewa, bi waɗannan matakan tsaro:

• • • Kada a taɓa fallasa fitattun masu haɗawa.
    • Bincika toshe tasha don abubuwan da ba su da sauƙi ko kowace alamar lalacewa. Sanar da NI idan an sami wata lalacewa.
    • Ajiye SCXI-1337 a cikin ambulan antistatic lokacin da ba a amfani da shi.

Tabbatar da Abubuwan:

Tabbatar kana da abubuwa masu zuwa:

• • • Tashar tashar tashar SCXI-1337
    • Farashin SCXI
    • SCXI-1129 canza launi
    • 1/8 in. flathead sukudireba
    • Lambobi 1 da 2 Phillips screwdrivers
    • Dogon hanci
    • Mai yankan waya
    • Waya mai rufe fuska

Haɗa Sigina:

Don haɗa sigina zuwa toshe tasha, bi waɗannan matakan:

1. • Tabbatar cewa ba a amfani da tsarin don haɗi zuwa sigina ko ma'auni tsakanin Rukunin II, III, ko IV, ko don hanyoyin samar da MAINS.
   • Shirya siginar siginar ta hanyar cire murfin ba fiye da 7 mm daga ƙarshen waya ba.
   • Cire dunƙule murfin saman kuma cire / cire murfin saman.
   • Sake ƙwanƙwasa nau'ikan nau'ikan nau'ikan nau'ikan nau'ikan nau'ikan nau'ikan nau'ikan nau'ikan nau'ikan nau'ikan nau'ikan nau'ikan nau'ikan iri biyu.
   • Guda wayoyi na sigina ta hanyar buɗewar damuwa.
   • Saka ƙarshen wariyar da aka cire gabaɗaya a cikin tashar kuma a tsare ta.

Bi waɗannan umarnin zai tabbatar da shigarwa da amfani da SCXI-1129 Terminal Block don NI SCXI-1337.

UMARNIN SHIGA

Toshe Tasha don NI SCXI-1129
Wannan jagorar yana bayyana yadda ake shigar da haɗa sigina zuwa National Instruments SCXI-1337 block block don saita SCXI-1129 sauya module azaman matrix 8 × 16 dual. Screw tashoshi akan SCXI-1337 yana ba ku damar samun dama ga kowane matrix 8 × 16. Hakanan SCXI-1337 yana ƙunshe da haɗin kai don ingantaccen fitarwa na na'urar daukar hotan takardu da siginonin shigar da bayanai na waje. Koma zuwa Jagoran Fara Fara Sauyawa NI don tantance lokacin shigar da toshe tasha. Ziyarci ni.com/switchs don bayani kan sauran hanyoyin sauyawa.

Taro

Ana amfani da ƙa'idodi masu zuwa a cikin wannan jagorar: Alamar » tana jagorantar ku ta abubuwan menu da aka gina da zaɓuɓɓukan akwatin maganganu zuwa mataki na ƙarshe. A jerin File» Saitin Shafi» Zaɓuɓɓuka suna jagorantar ku don saukar da File menu, zaɓi abu Saitin Shafi, kuma zaɓi Zabuka daga akwatin maganganu na ƙarshe. Wannan gunkin yana nuna bayanin kula, wanda ke faɗakar da ku ga mahimman bayanai. Wannan gunkin yana nuna taka tsantsan, wanda ke ba ku shawarar matakan kiyayewa don guje wa rauni, asarar bayanai, ko ɓarna na tsarin. Lokacin da aka yiwa wannan alamar alama akan samfur, koma zuwa Karanta Ni Farko: Tsaro da daftarin tsoma baki-Mit Radio don bayani game da matakan tsaro da yakamata a ɗauka.
M rubutu yana nuna abubuwa waɗanda dole ne ka zaɓa ko danna cikin software, kamar abubuwan menu da zaɓuɓɓukan akwatin maganganu. Rubutu mai ƙarfi kuma yana nuna sunaye.
Italic rubutu yana nuna mabambanta, girmamawa, ambaton giciye, ko gabatarwa ga maɓalli. Wannan font ɗin kuma yana nuna rubutu wanda shine ma'auni don kalma ko ƙima wanda dole ne ka bayar
monospace Rubutu a cikin wannan font yana nuna rubutu ko haruffa waɗanda yakamata ku shigar dasu daga maballin madannai, sassan lamba, programming examples, da syntax examples. Hakanan ana amfani da wannan font ɗin don ingantattun sunaye na faifai, hanyoyi, kundayen adireshi, shirye-shirye, shirye-shirye, ƙananan shirye-shirye, sunayen na'ura, ayyuka, ayyuka, masu canji, filesunaye da kari, da faifan code.

Buɗe Tushen Tasha

Don guje wa lalacewa wajen sarrafa toshewar tashar, ɗauki matakan tsaro masu zuwa:
Tsanaki Kada a taɓa fallasa fitattun masu haɗawa.

• Yi ƙasa ta amfani da madauri na ƙasa ko ta taɓa wani abu mai ƙasa.
• Taɓa fakitin antistatic zuwa wani ɓangaren ƙarfe na chassis na kwamfutarka kafin cire toshe tasha daga fakitin.

Cire toshe tasha daga kunshin kuma duba tashar tashar don abubuwan da ba su da tushe ko kowace alamar lalacewa. Sanar da NI idan tashar tashar ta bayyana lalacewa ta kowace hanya. Kar a shigar da toshe tasha mai lalacewa a cikin tsarin ku. Ajiye SCXI-1337 a cikin ambulan antistatic lokacin da ba a amfani da shi.

Tabbatar da Abubuwan

Tabbatar cewa kuna da abubuwa masu zuwa:

• Tashar tashar tashar SCXI-1337
• Farashin SCXI
• SCXI-1129 canza launi
• 1/8 in. flathead sukudireba
• Lambobi 1 da 2 Phillips screwdrivers
• Dogon hanci
• Mai yankan waya
• Waya mai rufe fuska

Haɗa Sigina

Don haɗa siginar (s) zuwa toshe tasha, koma zuwa Figures 1 da 2 yayin kammala waɗannan matakai:
Tsanaki An ƙididdige wannan ƙirar don Ma'auni na I kuma an yi niyya don ɗaukar sigina voltages ba ya fi 150 V. Wannan module ɗin na iya jure har zuwa 800 V mai ƙarfin kuzaritage. Kada kayi amfani da wannan tsarin don haɗi zuwa sigina ko don ma'auni tsakanin Rukunin II, III, ko IV. Kar a haɗa zuwa hanyoyin samar da MAINS (misaliample, kantunan bango) na 115 ko 230 VAC. Koma zuwa Jagoran Farawa na Sauyawa NI don ƙarin bayani kan nau'ikan aunawa. Lokacin da m voltages (> 42.4 Vpk / 60 VDC) suna nan akan kowane tashoshi na relay, aminci low-vol.tage (≤42.4 Vpk/60 VDC) ba za a iya haɗa shi zuwa kowane tashar relay ba.

1. Shirya siginar siginar ta hanyar cire murfin ba fiye da 7 mm daga ƙarshen waya ba.
2. Cire dunƙule murfin saman.
3. Cire kuma cire murfin saman.
4. Sake ƙwanƙwasa nau'ikan nau'ikan nau'ikan nau'ikan nau'ikan nau'ikan nau'ikan nau'ikan nau'ikan nau'ikan nau'ikan nau'ikan nau'ikan nau'ikan iri biyu.
5. Guda wayoyi na sigina ta hanyar buɗewar damuwa.
6. Saka ƙarshen wariyar da aka cire gabaɗaya a cikin tashar. Aminta da waya ta hanyar ƙara dunƙule tasha. Babu waya mara waya da zata wuce ta screw terminal. Wayar da aka fallasa tana ƙara haɗarin gajeriyar kewayawa ta haifar da gazawa.
7. Haɗa ƙasa amintaccen ƙasa zuwa mashin ƙasa mai aminci.
8. Matse sukurori biyu akan taron taimako don kiyaye igiyoyin.
9. Sake sanya murfin saman.
10. Sauya dunƙule murfin saman.
    1. Babban Rufin
    2. Top Cover Screw

Hoto na 1. SCXI-1337 Babban Hoton Hoton

1. Screw Terminals
2. Rear Connector
3. Umunƙun yatsa
4. Matsala-Relief Screw
5. Barci-Relief
6. Safety Ground Lug

Hoto na 2. SCXI-1337 Zane-zane Mai gano Sassan

Shigar da Terminal Block

Don haɗa SCXI-1337 zuwa gaban SCXI-1129, koma zuwa Hoto 3 kuma kammala waɗannan matakai:
Lura Shigar da SCXI-1129 idan ba ku riga kun yi haka ba. Koma zuwa Jagoran Farawa na Sauyawa don ƙarin bayani.

1. Toshe SCXI-1337 akan mahaɗin gaba na SCXI-1129.
2. Tsara babban yatsan yatsan hannu na sama da na ƙasa a bayan ƙarshen toshewar bango don riƙe shi amintacce a wurin.
   1. Babban yatsan yatsa
   2. Mai Haɗin Gaba
   3. Saukewa: SCXI-1129
   4. Saukewa: SCXI-1337

Ƙayyadaddun bayanai

Matsakaicin Aiki Voltage

• Matsakaicin aiki voltage yana nufin siginar voltage da na gama-gari voltage.
• Channel-zuwa-ƙasa………………………………………. 150V, Matsayin Shigarwa I
• Tashar-zuwa-tashar………………………………………. 150 V

Matsakaicin Yanzu

• Matsakaicin halin yanzu (kowane tashoshi) …………………………………………

Muhalli

• Yanayin aiki………………………………. 0 zuwa 50 ° C
• Ma'ajiyar zafin jiki………………………………. -20 zuwa 70 ° C
• Zama ................................................................................................ 10 zuwa 90%
• Degree Pollution……………………………………………… 2
• An amince da shi a tsayi har zuwa mita 2,000
• Amfani na cikin gida kawai

Tsaro
An ƙera wannan samfurin don biyan buƙatun ma'auni na aminci don kayan lantarki don aunawa, sarrafawa, da amfani da dakin gwaje-gwaje:

• IEC 61010-1, EN 61010-1
• UL 3111-1, UL 61010B-1
• CAN/CSA C22.2 Lamba 1010.1

Lura Don UL da sauran takaddun shaida na aminci, koma zuwa alamar samfur, ko ziyarta ni.com/certification, bincika ta lambar samfuri ko layin samfur, kuma danna hanyar haɗin da ta dace a cikin Shagon Takaddun shaida.

Daidaitawar Electromagnetic

• Wurshe ............................................
• Kariya
• EMC/EMI ……………………………………………….CE, C-Tick da FCC Sashe na 15 (Class A) Mai yarda

Lura Don yarda da EMC, dole ne kuyi aiki da wannan na'urar tare da igiya mai kariya.

Yarda da CE

Wannan samfurin ya cika mahimman buƙatun ƙa'idodin ƙa'idodin Turai, kamar yadda aka gyara don alamar CE, kamar haka:

• Ƙananan-Voltage Umarnin (lafiya)……………….73/23/EEC
• Daidaitawar Electromagnetic
• Umarni (EMC)……………………………………….89/336/EEC

Lura Koma zuwa Bayanin Daidaitawa (DoC) don wannan samfurin don kowane ƙarin bayanin yarda da tsari. Don samun DoC don wannan samfurin, ziyarci ni.com/certification, bincika ta lambar samfuri ko layin samfur, kuma danna hanyar haɗin da ta dace a cikin Shagon Takaddun shaida.

National Instruments, NI, ni.com, da LabVIEW alamun kasuwanci ne na National Instruments Corporation. Koma zuwa sashin Sharuɗɗan Amfani akan ni.com/legal don ƙarin bayani game da alamun kasuwanci na Instruments na ƙasa. Sauran samfura da sunayen kamfani da aka ambata a nan alamun kasuwanci ne ko sunayen kasuwanci na kamfanoni daban-daban. Don haƙƙin mallaka da ke rufe samfuran Kayan Ƙasa, koma zuwa wurin da ya dace: Taimako ikon mallaka.txt file na CD, ko ni.com/patents. © 2001-2007 National Instruments Corporation. An kiyaye duk haƙƙoƙi. 372791C Nov07 NI SCXI-1337 Umarnin Shigarwa 2 ni.com.

Takardu / Albarkatu

	KAYAN KASA SCXI-1129 Matrix Canja Module [pdf] Jagoran Shigarwa SCXI-1129, SCXI-1129 Matrix Canja Module, Matrix Canja Module, Canja Module, Module
	KAYAN KASA SCXI-1129 Matrix Canja Module [pdf] Jagoran Jagora SCXI-1129, SCXI-1129 Matrix Canja Module, Matrix Canja Module, Canja Module, Module

Magana

• Manual mai amfani