McWill 2ASIC GameGear Cikakken Jagorar Mai Amfani
Ƙayyadaddun bayanai
- Model SEGA Game Gear McWill FULL REV 2.1
- Abubuwan da ake buƙata: McWill GG FULL MOD PCB tare da 640 × 480 IPS, sabon allon wuta tare da batir LiPo, sabon allon sauti (na zaɓi), allon 'yar mata don 2ASIC KO 1ASIC da tashar iska mai zafi.
HANKALI! Cire da siyar da ASICs yana buƙatar ɗan gogewar siyar kuma yana kan haɗarin ku! Alhaki ba zai yiwu ba!
Abubuwan da ake buƙata:
McGill GG FULL MOD PCB tare da 640 × 480 IPS, sabon allon wuta tare da batir LiPo, sabon allon sauti (na zaɓi), allon 'yar mata don 2ASIC KO 1ASIC da tashar iska mai zafi.
Umarnin Amfani da samfur
Mataki 1: Cire ASICs da tashar jirgin ruwa na Cartridge
HANKALI! Tabbatar cewa duk wuta a kashe. Cire haɗin duk igiyoyi.
- Tabbatar cewa duk wuta a kashe kuma cire haɗin duk igiyoyi.
- Cire kristal 32.2159 MHz da tashar harsashi daga ainihin GG PCB.
- Amfani da tashar iska mai zafi, cire ASICs 2 da Z80 CPU (na PCBs 2ASIC) KO 1 ASIC (na PCB 1ASIC).
- Tsaftace duk fil ɗin guntu/kwakwalwa idan ya cancanta.
Mataki 2: Siyar da ASICs zuwa Allolin 'ya mace
Sayar da ASIC zuwa allon 'yar. Idan kuna da PCB 2ASIC kuma kuna buƙatar siyar da Z80 zuwa bayan allon 'yar. Sannan saka tashar harsashi. Bayan haka zaku iya siyar da kristal 32.2159 MHz zuwa PCB. Da fatan za a sake duba duk pads, musamman VCC da GND! Idan akwai gajeriyar kewayawa ASICs da FULL MOD na iya lalacewa!
PATCH na PCB 1ASIC: PINs 115, 116 da 117 (haɗe tare) suna buƙatar yin waya zuwa +5V VCC.
- PIN na 7 na hagu na ƙasa shine PIN 115, PIN na 8th PIN 116 kuma PIN na 9 shine PIN 117
- Don 1ASIC PCBs kuna buƙatar cire iyakoki 2 kuma ku maye gurbin resistor ta 0 Ohm ko gada (duba hoto na ƙarshe).
Lura: COPYRIGHT McWill 2023
Daughter board na 1ASIC GG:
- Sayar da ASIC zuwa allon 'yar.
- Idan kuna da PCB 2ASIC, kuma kuna siyar da Z80 zuwa bayan allon 'yar.
- Saka tashar harsashi.
- Sayar da kristal 32.2159 MHz zuwa PCB.
- Bincika duk pads sau biyu, musamman VCC da GND, don kowane gajeriyar kewayawa wanda zai iya lalata ASICs da FULL MOD.
PATCH don PCBs 1ASIC
PIN 115, 116, da 117 (haɗe tare) suna buƙatar yin waya zuwa +5V VCC. Kuna iya samun +5V VCC a hular tantalum mai rawaya a hannun dama na sama ko a hagu a resistor 912. PIN na 7 na hannun hagu shine PIN 115, PIN na 8 shine PIN 116, PIN na 9 kuma shine PIN 117. Domin 1ASIC PCBs, cire iyakoki 2 kuma maye gurbin resistor da 0 Ohm ko gada (duba hoto na ƙarshe).
Analog Stick / Saitunan Dpad
sandar analog na zaɓi ne. Idan kana son amfani da Dpad, cire sandar analog kuma saita sauyawa zuwa KASHE. Saitin ON yana sake kunna sandar analog. Ana ba da shawarar gwada halin sandar analog tare da wasanni daban-daban kafin cire shi. sandar analog na zaɓi ne! Idan kana son amfani da Dpad zaka iya cire sandar analog kuma saitin sauyawa ya kasance KASHE. Saitin ON yana sake kunna sandar analog. Amma ina ba da shawarar gwada halayen sandunan analog tare da wasanni daban-daban kafin cirewa.
Riƙe BUTTON UP sannan danna START don shigar da menu. Don barin menu danna BUTTON 2 koyaushe. Menu na 1 shine don sauyawa daga 3.5 ″ nuni zuwa DIGITAL VIDEO OUT ta latsa BUTTON 1. Danna maɓallin RIGHT sau ɗaya don menu na gaba don canzawa zuwa scanline ta danna BUTTON 1. Ta danna BUTTIN HAGU zaku shigar da menu na RGB LED. Danna BUTTON UP ko BUTTON DOWN yana canza launi na LED da aka zaɓa. Tabbatar da launi na LED ta danna BUTTON 1. BUTTON 2 yana kashe zaɓaɓɓen LED. Da zarar an kunna menu har yanzu sautin yana kunne kuma CPU yana aiki. Don musaki sauti da / ko cpu kuna buƙatar sanya ɓangarorin solder akan jumper SND da / ko JIRA jumper a dama.
ƘARIN GAME GAME:
Idan kuna son amfani da wasanpad, joysticks, ko kebul na hanyar haɗin GG, kuna buƙatar ƙara masu haɗin mata 1 ko 2 DSUB 9pin. Ana buƙatar datsa babba da ƙarami. Idan kuma kuna son amfani da gamepads, joysticks ko kebul na GG kuna buƙatar ƙara masu haɗin mata 1 ko 2 DSUB 9pin. Tabbas dole ne ku datsa babba da ƙananan harafin to.
Gyara Tagar Babban Harka
Don samun cikakken girman hoto kuna buƙatar datsa taga a hagu da dama don 640 × 480 IPS kaɗan kaɗan. Idan kuma kuna amfani da sandar analog kuna buƙatar datsa ƙaramin sashi a cikin babban harka a yankin Dpad. Wannan kit ɗin na zamani yana da sikelin lamba kawai kuma yanayin sikeli ba sa jin daɗi! In ba haka ba za ku iya amfani da daidaitaccen kayan aikin McWill GG tare da 320 × 240 LCD da yanayin ƙira.
GARGADI!
Wannan samfurin abu ne mai inganci kuma abin dubawa sau biyu. Yi amfani da allo na asali na McWill kawai da allon sauti tare da McWill GG FULL MOD. Hakanan, yi amfani da batir LiPo masu inganci kawai tare da da'irar kariya. In ba haka ba, McWill GG FULL MOD na iya lalacewa.
Labarai da Sabuntawa
Da fatan za a ziyarci nawa website don sabon hardware da bayanai: www.mcwill-retro.com
FAQ
Tambaya: Zan iya amfani da wasu allunan wutar lantarki da allon sauti tare da McWill GG FULL MOD?
A: Ana ba da shawarar yin amfani da allunan wutar lantarki na McWill na asali kawai da allon sauti don tabbatar da dacewa da kuma guje wa yuwuwar lalacewa ga McWill GG FULL MOD.
Tambaya: Wane irin batura zan yi amfani da su tare da McWill GG FULL MOD?
A: Ya kamata a yi amfani da batirin LiPo masu inganci tare da da'irar kariya don hana lalacewa ga McWill GG FULL MOD.
Tambaya: Ana buƙatar ƙwarewar siyarwa don cirewa da siyarwar ASICs?
A: Ee, cirewa da siyar da ASICs na buƙatar ɗan gogewa na siyarwar. Yana da mahimmanci a ci gaba da taka tsantsan kuma cikin haɗarin ku.
Takardu / Albarkatu
 |
McWill 2ASIC GameGear Cikakken Mod [pdf] Jagorar mai amfani 2ASIC GameGear Cikakken Mod, 2ASIC, GameGear Cikakken Mod, Cikakken Mod |
