GO Power GP-MPPT-PRO-BT-1 Bluetooth Dongle
Product Instructions
The GP-MPPT-PRO-BT-1 is compatible with Go Power!’s Bluetooth ready solar controllers and can work seamlessly with the Go Power! Connect mobile app giving you the ability to wirelessly monitor you controller’s parameters setting and data view.
Main Features
1. Convenient wireless monitoring of your solar controller
2. Supports the Go Power! Connect mobile app allowing for simple set-up and plug & play functionality
3. The use of high performance, low power consumption of the bluetooth special chip
4. Adopt bluetooth 4.0 and BLE technology, has the characteristics of rapid communication and strong
anti-jamming capability
5. Without external power supply, power supply directly by the communication port
6. Communication distance of up to 15 meters
LED Status
| Indicator Light | State | Explanation |
| Link Indicator Light | Blink | Connected |
| OFF | Idle State |
Applicable Type
| Communication | Controller Port |
| RS232 | RJ12 |
Product Features
Product Dimensions
System Wiring Diagram
Note: Cable using the standard network cable (parallel line) connect.
Specifications
| Type GP-MPPT-PRO-BT-1 | |
| Input voltage | 5V-12V |
| Stand-by power consumption | 0.04W |
| Run power consumption | 0.05W |
| Communication distance | ≤15m |
| Serial port baud rate | Fixed baud rate 9600bps |
| Communication methods | RS232 |
| Interface type | RJ12 |
| Connecting line | Standard network cable (parallel line) |
| Size | 66.3 x 51 x 15mm |
| Installation dimension | 57.5 x 15mm |
| Fixed holes dia | φ3.5 |
| Operating temperature | -20℃-75℃ |
| Level of protection | IP67 |
| Net weight | 120g |
Support: https://gpelectric.com/support/battery-monitor-support/
Connectivity Instructions
Welcome to the Go Power! ConnectTM Manual. You can use the Connect app to configure, monitor and diagnose all our products which have built-in Bluetooth capability or are equipped with a Go Power! direct port.
For a complete list of products compatible with Go Power! Connect, please visit gpelectric.com
Go Power ConnectTM can be used on devices running Android or iOS.
- Download and Installation
Go Power ConnectTM is available to users of iOS and Android phones, as well as tablets. Visit get.gpelectric.com/connect to download the app suitable for your device. - Bluetooth Dongle – Pairing and Connecting
- Open Go Power! ConnectTM
- On your Phone or Tablet: pull down the screen to initiate a scan for available devices.
- The first time you attempt to connect the phone will ask to ‘pair’ with the device. Enter the pin code. The default pin code is 000000.
- Connection is complete.
If connection was not successful please refer to section 9. Troubleshooting below.
Note: Always connect from within the Go Power! ConnectTM app. Do not connect from the device’s system menu because the app will not find your Go Power! product.
Changing the Bluetooth PIN code
To prevent unauthorised connections to your device we recommended you change the PIN code. Avoid using obvious PIN codes such as 111111 or 123456.
To change the PIN code: First complete your connection; then go to the Product Info page. To access that page, click the button on the upper right. For some products it will be the settings icon: .
After opening that menu press , and click Product Info.
For other products you’ll find the button on the upper right, which takes you straight to the Product Info page.
Compatibility notes on phones and tablets
Android Devices
The minimum required Android version to run the Go Power ConnectTM app is 4.1.
The minimum required Android version to connect to the Go Power! ConnectTM via Bluetooth is 4.3.
Access to location services required?
Android 6 and later requires access permission for the Connectivity app to access location services. Otherwise it can not scan for the Bluetooth devices.
Besides permitting access to its data, the location services also needs to be enabled in many (but not all) cases.
Note that after enabling location services, the GPS itself can be switched off again: the Android location services are more than GPS. Bluetooth and WiFi- scan results can technically also be used to approximate the devices location; hence these requirements.
Despite the text above, you can be sure that the Connectivity app is not interested in, nor tracking your location.
Apple iOS iPhones and iPads
The Connectivity app works on the following iPhones and iPads, which have Bluetooth 4.0 (BT LE) and iOS 8 or later, which is required:
• Phone 4S and later (due to Bluetooth Low Energy support)
• iPad 3rd generation and later
Unfortunately Apple iPhone/iPad doesn’t support USB OTG.
Documents / Resources
 |
GO Power GP-MPPT-PRO-BT-1 Bluetooth Dongle [pdf] Owner's Manual GP-MPPT-PRO-BT-1, Bluetooth Dongle |
