GDU-Tech A4G-200A 4G Expansion Module Instruction Manual

A4G-200A 4G Expansion Module

Product Specifications

  • Voltage: DC14.4V
  • Communication Interface: USB 2.0
  • Static Power Consumption: 4.788W
  • Maximum Power Consumption: 5W
  • IP Rating: IP43
  • Operating Temperature: -20°C to +50°C
  • Dimensions: 95g
  • Weight: 95g

Installation Steps

  1. Lift the rubber USB cover on the top of the aircraft and
    connect the Type-C port.
  2. Tighten the two thumb screws clockwise on the top.
  3. Loosen side brackets, rotate to diagram position, and tighten
    clockwise into fuselage screw holes.

Any changes or modifications not expressly approved by the
party responsible for compliance could void the user’s authority to
operate the equipment.

This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause
undesired operation.

This equipment complies with FCC radiation exposure limits set
forth for an uncontrolled environment. This equipment should be
installed and operated with a minimum distance of 20cm between the
radiator and your body.

Frequently Asked Questions (FAQ)

Q: What is the purpose of the 4G Expansion Module?

A: The 4G Expansion Module provides enhanced communication
capabilities for the aircraft.

Q: Is the 4G Expansion Module waterproof?

A: The 4G Expansion Module has an IP Rating of IP43, indicating
partial protection against water ingress.

Q: Can the 4G Expansion Module be used in extreme
temperatures?

A: The operating temperature range of the 4G Expansion Module is
from -20°C to +50°C, allowing for use in varied temperature
conditions.

“`

4G Expansion Module
The 4G expansion module is a net-connected airborne terminal that eliminates remote controller distance limitations, networked remote control, real-time transmission, cloud synchronization, and real-time data acquisition and processing. The wireless digital transmission terminal utilizes the mature LTE network, offering broader coverage, higher transmission speed, and lower latency. It is designed to provide high-quality wireless connectivity services for various IoT industry applications. This device has a fixed matching product (FCC ID: 2A8WC-S220PRO).

Technical Indicators

Vo l t a g e

DC14.4V

Communication interface USB 2.0

Static pow er consumption 4.788W

Maximum pow er co n su m p t i o n

5W

IP Rating

IP43

Operating Temperature -20 ~+50

Di m en si o n s

144mm×252mm×50mm(±2mm)

Wei g h t

95g

Installation Steps
1. Lift the rubber USB cover on the top of the aircraft and connect the Type-C port.
2. Tighten the two thumb screws clockwise on the top.

3. Loosen side brackets, rotate to diagram position, and tighten clockwise into fuselage screw holes.

Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: –Reorient or relocate the receiving antenna. –Increase the separation between the equipment and receiver. –Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. –Consult the dealer or an experienced radio/TV technician for help.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator& your body.

Documents / Resources

GDU-Tech A4G-200A 4G Expansion Module [pdf] Instruction Manual
A4G-S200A, A4G-200A 4G Expansion Module, A4G-200A, 4G Expansion Module, Expansion Module, Module

References

Leave a comment

Your email address will not be published. Required fields are marked *