80S ENGINEERING OBC v2.0 On-Board Computer Replica

Sònrachaidhean

• Taisbeanadh uair is ceann-latha
• Astar GPS le inneal-rabhaidh thar-luath
• Timers 0-60 agus 1/4 mìle
• Uaireadair lap
• Caitheamh, raon, connadh a tha air fhàgail, agus odometer turas
• Stad-uaireadair
• Voltmeter, cuideam ola, teòthachd le inneal-rabhaidh ro theth
• Teòthachd a-muigh, altimeter, ceann, agus g-sensor
• OBC v2.0 Setting/Resetting and On/Off

Stiùireadh airson cleachdadh bathar

Uair agus ceann-latha.

Astar GPS agus inneal-rabhaidh thar-luath.

Timers 0-60 agus 1/4 mìle.

Uaireadair lap.

Consumption, range, remaining fuel, and trip odometer.

Stad-uaireadair.

Voltmeter, oil pressure and temperature, with overheat alarm.

Teòthachd a-muigh, altimeter, ceann, agus g-sensor.

Suidhich / ath-shuidheachadh agus air / dheth.

: A-mhàin airson rèiteachaidhean co-fhreagarrach

UAIR/Ceann-latha:
Press the designated button to display the current time. Press again to switch to the date view. Adjust the time and date by pressing the appropriate buttons.

Luas GPS:
Brùth gu view the current GPS speed.d Press to display the current GPS speed. The overspeed alarm can be activated using . Press once to set the limit speed using the numerical buttons, and press again to activate the alarm (‘ON’ will be displayed). Repeat the operation to deactivate the alarm. In case of an overspeed, ‘LIMIT’ will blink on the screen until you slow down. You can ignore the alarm by pressing .0-60 agus 1/4 MILE TIMER: 

Brùth to display the 0-62 timer. ‘READY’ will be displayed once at full stop. The 0-62 timer will start right when an acceleration is detected and will stop once you reach 62mph (100km/h). Press again to display the 1/4 mile timer, which operates the same.

LAP TIMER: 

Brùth to display the lap timer. Press to set the starting line to your current position. A running timer will then get displayed, until you cross the starting line, which will display the elapsed lap time. Your fastest lap and delay with it will also get displayed on the following laps.
Brùth to end the lap timing. Your fastest lap and total number of laps will be displayed.

MPG, raon, connadh air fhàgail, AGUS ODOMETER TRIP: 

Brùth gu leantainneach to display your hourly fuel consumption, mileage, range, remaining fuel (if compatible), and trip odometer. Those values are computed from variables (injector size, engine type, etc) that need to be set up. Please refer to page 12. The tripp odometer can be/reset using

TIMER: 

Brùth to display the stopwatch. It can be started and stopped with. Once stopped, preas to reset. The stopwatch features a split function allowing for the timing of a second interval, which can be activated by
A' bruthadh when the stopwatch is running

SGEULACHDAN: 

Brùth gu leantainneach to display the oil pressure, oil temperature (if equipped), and voltage. An overheat alarm can be activated by pressing , which will display an alert message if your temperature exceeds a pre-selected value, which can be ignored by pressing

 FIOSRACHADH. Brùth gu leantainneach to display outdoor temperature (if equipped), accelerometer, current heading, and altimeter.

SET / RESET:
Brùth agus cum to power on/off the onboard computer. The OBC will automatically power off if left inactive for an extended period

Digisean

As mentioned earlier, some functions may take numerical values. These values can be entered using the dig buttons. Example: Pre ss + + + to enter 112.  You can also enter negative numbers by pressing and holding the corresponding buttons.

Suidhichidhean

Faodar faighinn gu roghainnean le bhith a’ putadh aig an aon àm agus . Tha gach suidheachadh co-cheangailte ri àireamh fhreagarrach, mar a tha air a mhìneachadh sa chlàr a leanas:

Wifi UPDATES. 

• New software updates will frequently be released to fix potential bugs and add features.
• To install them, please navigate to the setting “SET 3”.
• For one minute, the OBC will try to connect to a known Wi-Fi hotspot to download the latest version of the software.
• If no known WiFi hotspot is available, or if none has ever been registered, the device will become an access point, waiting for you to connect to it.
• Using either your phone or your computer, please look up the “E30 OBC” WiFI hotspot.
• Once connected to it, you will get redirected to obc-80s.engineering.
• There, please type in an available WiFi hotspot SSID and password.
• Once registered, the OBC will use those WiFi credentials to attempt to connect to the internet, where it will download the latest software. (from https://github.com/80sEngineering/OBC)

Tuilleadh fiosrachaidh

• SIGNAL’implies that the GPS module is searching for a satellite signal. It will be displayed if the car is underground or if the
• OBC has not been used in some time. It should disappear in about 30 seconds with good visibility of the sky.
• Feartan dealain:
  • Solarachadh voltage: 7-25V
  • Maximum operating consumption: ~180mA
  • Current consumption when off: <0.3mA (essentially nothing)

Any iissues:
Please reach me at contact @80s.engineering or on Instagram @80s.engineering for a faster answer.
Thanks for your support and bonne route!

Ceistean Cumanta

C: Ciamar a shuidhicheas mi na caochladairean airson fiosrachadh co-cheangailte ri connadh?
A: Please refer to page 12 of the manual for instructions on setting up variables such as injector size and engine type.

C: Ciamar a bheir mi seachad inneal-rabhaidh air a bhrosnachadh le cus teas?
A: You can ignore the overheat alarm by pressing the designated button, as mentioned in the manual.

C: Dè thachras ma dh'fhàgas mi an OBC neo-ghnìomhach airson ùine mhòr?
A: The OBC will automatically power off if left inactive for an extended period to conserve energy.

Sgrìobhainnean/Goireasan

80S ENGINEERING OBC v2.0 Mac-samhail Coimpiutair air bòrd [pdfLeabhar-stiùiridh OBC v2.0, OBC v2.0 Mac-samhail coimpiutair air bòrd, mac-samhail coimpiutair air bòrd, mac-samhail coimpiutair

Iomraidhean

• Leabhar-làimhe cleachdaiche