FT1206YG Remote Control Transmitter
Product Information
Specifications
- Name: FT1206YG Remote Control Transmitter
- LED Indicator: Yes
- Power Source: 12V/23A battery
- Buttons: Fan ON/OFF, Fan Speed Up, Fan Speed Down, Fan
Forward/Reverse, Light ON/OFF, Color switching - Standby Function: Yes
Product Usage Instructions
Operation Instructions
- LED Indicator: Indicates power status and
operation mode. - Fan ON/OFF (Pairing Button): Used to turn the
fan on or off and for pairing purposes. - Fan Speed Up: Increases the fan speed.
- Fan Speed Down: Decreases the fan speed.
- Fan Forward/Reverse: Changes the direction of
the fan rotation. - Light ON/OFF: Controls the lighting
feature. - Color Switching: Changes the color settings if
applicable. - BATTERY: Requires a 12V/23A battery. Ensure
proper installation and replace when low. - Standby: Puts the transmitter in standby mode
when not in use.
Use Precautions
- If the LED indicator does not illuminate when pressing a key,
check the battery installation. - If the LED indicator flashes when pressing a key, replace the
battery with a new one due to low voltage. - Remove the battery from the transmitter if not in use for an
extended period.
FAQ
Frequently Asked Questions
- Q: What should I do if the LED indicator doesn’t turn on?
- A: Check the battery installation and ensure it is properly
inserted. - Q: How do I know when to replace the battery?
- A: If the LED indicator flashes when pressing a key, it
indicates low battery voltage, and you should replace it with a new
one. - Q: What is the FCC ID for this transmitter?
- A: The FCC ID for the FT1206YG Remote Control Transmitter is
2ABUP-FT1206YG.
USER MANUAL FOR FT1206YG REMOTE CONTROL TRANSMITTER
I. Operation Instructions
1 LED Indicator 2 Fan ON/OFF(Pairing Button) 3 Fan Speed Up 4 Fan Speed Down 5 Fan Forward/Reverse 6 Light ON/OFF 7 Color switching 8 BATTERY: 12V/23Ax1 9 Standby
II. Use precautions
1. When press the key of transmitter, the LED indicator doesn’t on, please inspect the battery installation. 2. When press the key of transmitter, the LED indicator flashing, that means the battery get low voltage, please
replace a new one. 3. Please pull out of the battery from the transmitter when leaving unused for a long time.
FCC Instructions
This product has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This product generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If the product does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
— Reorient or relocate the receiving antenna. — Increase the separation between the product and receiver. — Connect the product into an outlet on a circuit different from that to which the receiver is connected. — Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device m not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause Undesired operation. Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the product.
FCC ID: 2ABUP-FT1206YG
Documents / Resources
 |
FUNPOWER FT1206YG Remote Control Transmitter [pdf] User Manual 2ABUP-FT1206YG, 2ABUPFT1206YG, FT1206YG Remote Control Transmitter, FT1206YG, Remote Control Transmitter, Control Transmitter, Transmitter |