FSP Power Solution FP Series Line Interactive UPS
Package Contents
You should have received the following items inside of package:
- UPS Unit
- Quick Guide
- Power cable (only for the IEC-type input model)
Product Overview
Front View:
- Power Switch
- AC Mode: green lighting
- Battery Mode: yellow flashing
- Fault LED: red lighting
Back View: 
- Output receptacles
- AC input
- Circuit breaker
- USB port
- Modem/phone/network surge protection
Installation and Initial Startup
NOTE: Before installation, please inspect the unit. Be sure that nothing inside the package is damaged.
Placement & Storage Conditions
Install the UPS in a protected area that is free of excessive dust and has adequate air flow. Please place the UPS away from other units at least 20 cm to avoid interference. Do NOT operate the UPS where the temperature and humidity is outside the specific limits. (Please check the specs for the limitations.)
Connect to Utility and Charging
Plug in the AC input cord to the wall outlet. For the best results, suggest to charge the battery at least 6 hours before initial use. The unit charges its battery while connecting to the utility. 
Connect the Loads
Plug in the loads to output receptacles on the rear panel of the UPS. Simply turn on the power switch of UPS unit, then devices connected to the UPS will be protected by UPS unit.
CAUTION: NEVER connect a laser printer or scanner to the UPS unit. This may cause the damage of the unit.
Turn On/Off the Unit
Turn on the UPS unit by pressing the power switch. Turn off the UPS unit by pressing again the power switch. 
Important Safety
Important Safety Warning (SAVE THESE INSTRUCTIONS)
- CAUTION! To prevent the risk of fire or electric shock, install in a temperature and humidity controlled indoor area free of conductive contaminants. (See the specifications for the acceptable temperature and humidity range.)
- CAUTION! To reduce the risk of overheating the UPS, do not cover the UPS’ cooling vents and avoid exposing the unit to direct sunlight or installing the unit near heat emitting appliances such as space heaters or furnaces.
- CAUTION! Do not attach non-computer-related items, such as medical equipment, life-support equipment, microwave ovens, or vacuum cleaners to UPS.
- CAUTION! Do not plug the UPS input into its own output.
- CAUTION! Do not allow liquids or any foreign object to enter the UPS. Do not place beverages or any other liquid-containing vessels on or near the unit.
- CAUTION! In the event of an emergency, press the OFF button and disconnect the power cord from the AC power supply to properly disable the UPS.
- CAUTION! Do not attach a power strip or surge suppressor to the UPS.
- CAUTION! If the UPS is with metal chassis, for safety purpose, grounding is a must during UPS installation in order to reduce leakage current below 3.5mA.
- Attention: hazardous through electric shock. Also with disconnection of this unit from the mains, hazardous voltage still may be accessible through supply from battery. The battery supply should be therefore disconnected in the plus and minus pole at the quick connectors of the battery when maintenance or service work inside the UPS is necessary.
- CAUTION! Servicing of batteries should be performed or supervised by personnel knowledgeable of batteries and the required precautions. Keep unauthorized personnel away from batteries.
- CAUTION! When replacing the batteries, use the same number and type of batteries. CAUTION! Internal battery voltage is 12VDC. Sealed, lead-acid, 6-cell battery.
CAUTION! Unplug the UPS prior to cleaning and do not use liquid or spray detergent. CAUTION! A battery can present a risk of electric shock and high short circuit current. The following precaution should be observed before replacing batteries:
- Remove watches, rings, or other metal objects.
- Use tools with insulated handles.
- Wear rubber gloves and boots.
- Do not lay tools or metal parts on top of batteries.
- Disconnect charging source prior to connecting or disconnecting batteries terminal.
TroubleShooting
Use the table below to solve minor problems.
| Problem | Possible Cause | Solutions |
| LED display on the front panel does not work. | Low battery | Charge the UPS at least 6 hours. |
| Battery fault | Replace the battery with the same type of battery. | |
| The UPS is not turned on. | Press the power switch again to turn on the UPS. | |
| Alarm continuously sounds when the mains is normal. | The UPS is overload. | Remove some loads first. Before reconnecting equipment, please verify that the load matches the UPS capability specified in the specs. |
| When power fails, back-up time is shorten. | The UPS is overload. | Remove some critical load. |
| Battery voltage is too low. | Charge the UPS at least 6 hours. | |
| Battery defect. It might be due to high temperature operation environment, or improper operation to battery. | Replace the battery with the same type of battery. | |
| The mains is normal Bu the unit is on battery mode. | Power cord is loose. | Reconnect the power cord properly. |
Specifications
| Model | FP 1000 | FP 1500 | FP 2000 |
| CAPACITY | 1000 VA / 600 W | 1500 VA / 900 W | 2000 VA / 1200 W |
| INPUT | |||
| Voltage | 220/230/240 VAC | ||
| Voltage Range | 162-290 VAC | ||
| OUTPUT | |||
| Voltage Regulation | +/-10% | ||
| Transfer Time | Typical 2-6 ms, 10 ms max. | ||
| Waveform | Simulated Sine Wave | ||
| BATTERY | |||
| Type & Number | 12 V/7 AH x 2 | 12 V/9 AH x 2 | 12 V/9 AH x 2 |
| Charging Time | 4-6 hours recover to 90% capacity | ||
| PHYSICAL | |||
| Dimension (DxWxH) | 320 x 130 x 182 mm | ||
| Net Weight (kgs) | 8.2 | 10.4 | 11.0 |
| Environment | |||
| Humidity | 0-90 % RH @ 0-40° C (non-condensing) | ||
| Noise Level | Less than 40 dB | ||
Frequently Asked Questions
Can I connect a laser printer or scanner to the UPS?
No, it is not recommended to connect a laser printer or scanner to the UPS as it may cause damage to the unit.
How long should I charge the UPS battery before initial use?
It is suggested to charge the battery for at least 6 hours before initial use for best results.
Documents / Resources
 |
FSP Power Solution FP Series Line Interactive UPS [pdf] User Guide FP 1000, FP 1500, FP 2000, FP Series Line Interactive UPS, FP Series, Line Interactive UPS, Interactive UPS, UPS |