FORTINET EVO-ALL Immobilizer Bypass Module

Vehicle functions

supported in this diagram (functional if equipped)

NOTES

THIS MODULE MUST BE INSTALLED BY A QUALIFIED TECHNICIAN.

• Parts required (Not included)
  • 1X 10 AMP Fuse

MANDATORY INSTALL

• HOOD PIN
  • HOOD STATUS : THE HOOD PIN SWITCH MUST BE INSTALLED IF THE VEHICLE CAN BE REMOTE STARTED WITH THE HOOD OPEN,\ SET FUNCTION A11 TO OFF.

Notice: the installation of safety elements are mandatory. The hood pin is an essential security element and must be installed.

• THIS MODULE MUST BE INSTALLED BY A QUALIFIED TECHNICIAN. A WRONG\ CONNECTION CAN CAUSE PERMANENT DAMAGE TO THE VEHICLE.

DESCRIPTION

Under steering column, START-STOP unit.

ATTENTION

Before disconnecting a module, a computer or a control unit from a vehicle: Always disconnect the negative terminal from the vehicle’s battery.In these vehicles, the factory keyless entry module is sensitive to interference and may cease to operate if some precautions are not taken. Disconnect the (-) terminal of the battery prior to disconnecting the connectors at the smartkey module below the steering wheel to avoid damage to the smartkey entry module.

1. Disconnect the (-) terminal of the battery.
2. 
   1. Unscrew
      • Under the Steering Column
   2. Unscrew
      • Under the Steering Column
   3. Onclip
      • Left of Steering Column
   4. Onclip
      • Right of the Steering Column
   5. Gently pull up the cover of the steering column.
3. Make the following connections.

WIRING CONNECTION

AUTOMATIC TRANSMISSION WIRING CONNECTION

MANUAL TRANSMISSION WIRING CONNECTION

Reconnect the (-) terminal of the battery.

DCRYPTOR PROGRAMMING PROCEDURE

BEFORE PROGRAMMING

BEFORE PROGRAMMING, SET THE UNIT OPTIONS AND SAVE

1. Press and hold the programming button: Connect the 4-PIN Data-link harness (Black connector).
   • The Blue, Red, Yellow and Blue & Red LEDs will alternatively illuminate.
2. Release the programming button when the Blue LED is ON.
   • If the LED are not solid BLUE, disconnect the 4-PIN Data-link harness (Black connector) and go back to step1.
3. Connect the required remaining harnesses.
4. Do not press the brake pedal. Press the Push-to-Start button twice to turn ON the ignition.
   • The Blue, Red and Yellow LEDs will alternatively illuminate.
     wait,
   • The BLUE LED will flash rapidly.
5. Press the Push-to-Start button once to turn off the ignition.
   • The BLUE LED will turn off.
   • The RED and YELLOW LEDs will alternate.

KEY BYPASS PROGRAMMING PROCEDURE 2/2

REMOTE STARTER FUNCTIONALITY

Notice: Updated Firmware and Installation Guides

Updated firmware and installation guides are posted on our website on a regular basis. We recommend that you update this module to the latest firmware and download the latest installation guide(s) prior to the installation of this product.

Module label

WARNING

The information on this sheet is provided on an (as is) basis with no representation or warranty of accuracy whatsoever. It is the sole responsibility of the installer to check and verify any circuit before connecting to it. Only a computer-safe logic probe or digital multimeter should be used. FORTIN ELECTRONIC SYSTEMS assumes absolutely no liability or responsibility whatsoever pertaining to the accuracy or currency of the information supplied. The installation in every case is the sole responsibility of the installer performing the work, and FORTIN ELECTRONIC SYSTEMS assumes no liability or responsibility whatsoever resulting from any type of installation, whether performed properly, improperly or any other way. Neither the manufacturer nor the distributor of this module is responsible of damages of any kind directly or indirectly caused by this module, except for the replacement of this module in case of manufacturing defects. This module must be installed by a qualified technician. The information supplied is a guide only. This instruction guide may change without notice. Visit www.fortinbypass.com to get the latest version.

TECH SUPPORT

• Tél: 514-255-HELP (4357)
• 1-877-336-7797
• www.fortinbypass.com

This guide may change without notice. See www.fortin.ca for the latest version

FAQ

• Q: Is it necessary to install the hood pin switch?
  • A: Yes, if the vehicle is not equipped with a functional hood pin, it is mandatory to install the hood pin switch for proper operation and security.
• Q: Can I program the bypass option myself?
  • A: It is recommended to have a qualified technician program the bypass option to avoid any incorrect configurations that may cause damage to the vehicle.
• Q: What precautions should I take when disconnecting components?
  • A: Always disconnect the negative terminal from the battery before disconnecting any modules or control units from the vehicle to prevent interference or damage to sensitive components like the factory keyless entry module.

Documents / Resources

FORTINET EVO-ALL Immobilizer Bypass Module [pdf] Installation Guide 63511, AR35, EVO-ALL Immobilizer Bypass Module, EVO-ALL, Immobilizer Bypass Module, Bypass Module

References

• User Manual