REV.: 20250317
GUIDE # 111631
EVO ALL All In one Data Bypass and Interface Module
THAR-SUB4 THARNESS STAND ALONE INSTALLATION
ADDENDUM – SUGGESTED WIRING CONFIGURATION
VEHICLE
YEARS
2023-2024
SUBARU
Ascent
Push-to-Start
Vehicle functions supported in this diagram (functional if equipped)
- Immobilizer bypass
- Lock
- Unlock
- Arm
- Disarm
- Trunk (open)
- Parking Lights
- Heated Seats
AUX.1: - Rear Defrost
- RAP Shutdown
- Tachometer
- Door Status
- Trunk Status
- Hand-Brake Status
- Foot-Brake Status
- Secure Take Over
COMPATIBLE MODULE REQUIRED:
QR CODE
ON THE LABEL MANUFACTURED AFTER: 2019
FIRMWARE VERSION
93.[01]
MINIMUM
To add the firmware version and the options, use the FLASH LINK UPDATER or FLASH LINK MOBILE tool, sold separately.
Program bypass option:
| UNIT OPTION | DESCRIPTION |
| C1 | OEM Remote status (Lock/Unlock) monitoring |
| D6 | Push-to-Start |
IF THE VEHICLE IS NOT EQUIPPED WITH FUNCTIONAL HOOD PIN:
A11  |
Hood trigger (Output Status). |
Program bypass option
(For RAP shutdown):
| D5 | Lock after start |
NOTES
MAKE SURE THE KEY IS NOT INSIDE THE CAR WHENREMOTE STARTING.
Parts required (Not included)
1X RF KIT
MANDATORY INSTALL
HOOD STATUS : THE HOOD PIN SWITCH MUST BE INSTALLED IF THE VEHICLE CAN BE REMOTE STARTED WITH THE HOOD OPEN, SET FUNCTION A11 TO OFF.
A11
Notice: the installation of safety elements are mandatory. The hood pin is an essential security element and must be installed.
THIS MODULE MUST BE INSTALLED BY A QUALIFIED TECHNICIAN. A WRONG CONNECTION CAN CAUSE PERMANENT DAMAGE TO THE VEHICLE.
PARTS REQUIRED (NOT INCLUDED)
STAND ALONE CONFIGURATION
Program bypass option with oem remote:
| UNIT OPTION | DESCRIPTION |
| C1 | OEM Remote Monitoring |
Program bypass option with RF KIT antenna:
| UNIT OPTION | DESCRIPTION |
| H1 to H6 | Supported RF Kits and select RF Kit |
REMOTE STARTER FUNCTIONNALITY
The 3x LOCK remote start function with the OEM remote control is not recommended, the original vehicle remote control will not be functional while the engine is running.
RF KIT required (sold separately)
REMOTE STARTER DIAGNOSTICS
MODULE RED LED
x2 flash : Brake ON
x3 flash : No tach
x4 flash : Ignition before start
x5 flash : Hood Open
REMOTE STARTER WARNING CARD
CUT THIS WARNING CARD AND STICK IT ON A VISIBLE PLACE: or use the package RSPB, Sold separately.
WARNING
REMOTE STARTER
THE VEHICLE CAN BE STARTED BY EITHER: PRESSING THE LOCK BUTTON ON THE OEM REMOTE 3 TIMES CONSECUTIVELY OR BY A SMARTPHONE. TURN ON THE SAFETY SWITCH LOCATED UNDER THE DASHBOARD BEFORE WORKING ON THE VEHICLE.
AUTOMATIC TRANSMISSION WIRING CONNECTION
KEY BYPASS PROGRAMMING PROCEDURE 1/3
Keep the other OEM remotes away from the vehicle. Minimum 3 meters (10 feet).
- Press and hold the programming button: the 4-Pin (Data-Link) connector. Insert
The Blue, Red, Yellow and Blue & Red LEDs will alternatively illuminate.
- Release the programming button when the LED is BLUE.
If the LED is not solid BLUE disconnect the 4-Pin connector (Data-Link) and go back to step 1.
- Insert the required remaining connectors.
- Do not press the brake pedal.
Press the START/STOP button twice to turn ON the ignition.
- Press and release the programming button once (1x).
- Press the START/STOP button once to turn OFF the ignition.
- Remove the battery from 1 OEM remote.
Keep the other OEM remotes away from the vehicle. Minimum 3 meters (10 feet).
- Place the OEM remote (no battery) close to the front of START/STOP button as shown.
- Press the footbrake pedal.
Release the pedal. - Press the START/STOP button once to turn OFF the ignition.
- Place the OEM remote (no battery) close to the front of START/STOP button as shown.
- Press the footbrake pedal.
The vehicle ignition will turn ON.
The YELLOW LED will turn ON.
The RED LED will turn OFF.
Release the pedal. - Press the START/STOP button once to turn OFF the ignition.
The RED and YELLOW LEDs will alternated.
- Disconnect all the connectors and after the Data-Link (4-pins) connector.
- Use the tool:
FLASH LINK UPDATER or FLASH LINK MOBILE to visit the DCryptor menu.
*Parts required (not included)
- AFTER DCRYPTOR PROGRAMMING COMPLETED
Go back to the vehicle and reconnect the 4-Pin (Data-Link) connector and after, all the remaining connector.
The module is now programmed.
REMOTE STARTER / ALARM VERIFICATION PROCEDURE
FUNCTIONS
The engine will shutdown when a door is opened if the vehicle is not Unlocked.
Module label
Notice: Updated Firmware and Installation Guides
Updated firmware and installation guides are posted on our web site on a regular basis. We recommend that you update this module to the latest firmware and download the latest installation guide(s) prior to the installation of this product.
WARNING
The information on this sheet is provided on an (as is) basis with no representation or warranty of accuracy whatsoever.
It is the sole responsibility of the installer to check and verify any circuit before connecting to it. Only a computer safe logic probe or digital multimeter should be used. FORTIN ELECTRONIC SYSTEMS assumes absolutely no liability or responsibility whatsoever pertaining to the accuracy or currency of the information supplied. The installation in every case is the sole responsibility of the installer performing the work and FORTIN ELECTRONIC SYSTEMS assumes no liability or responsibility whatsoever resulting from any type of installation, whether performed properly, improperly or any other way. Neither the manufacturer or distributor of this module is responsible of damages of any kind indirectly or directly caused by this module, except for the replacement of this module in case of manufacturing defects. This module must be installed by qualifi ed technician. The information supplied is a guide only. This instruction guide may change without notice. Visit www.fortinbypass.com to get the latest version.
This guide may change without notice. See www.fortin.ca for latest version.
TECH SUPPORT
Tél: 514-255-HELP (4357)
1-877-336-7797
ADDENDUM GUIDE
www.fortinbypass.com
WEB UPDATE
Documents / Resources
 |
FORTIN EVO ALL All In one Data Bypass and Interface Module [pdf] Installation Guide THAR-SUB4, EVO-ALL, Subaru Ascent 2023, EVO ALL All In one Data Bypass and Interface Module, EVO ALL, All In one Data Bypass and Interface Module, one Data Bypass and Interface Module, Interface Module, Module |