FlySpark F4 V1 Stack Flight Controller User Manual

FlySpark F4 V1 Stack Flight Controller

Specifications

• Product Name:
  FlySpark F4 V1 BLS 60A Stack
• AI Features:
  Sensor Fusion, PID Autotuning, Adaptive Filtering
• Software Support:
  Betaflight, INAV, Ardupilot, EMU-flight, SkyBrush
• ESC Communication:
  BLHeli_S Bluetooth & USB-C
• Connectivity:
  3-6S LiPo
• Dimension:
  47.8mm(L) x 47.5mm(W) x 18.3mm(H)
• Mounting:
  30.5 x 30.5mm with 4mm hole size
• Weight:
  34g

Product Usage Instructions

FlySpark F4 V1 Flight Controller

Layout:
Refer to the user manual for the layout of the flight controller.

Peripheral Connection:
Connect peripherals as per the provided diagram.

App & FC Configuration:
Use the recommended apps and follow the configuration instructions.

FC Firmware Update:
Connect the flight controller to a PC via USB for firmware updates.

FLYSPARK BLS 60A 4-IN-1 ESC

Layout:
Check the layout guide in the manual for proper installation.

Connection with Motors & Power Cable:
Connect motors and power cables securely.

ESC Configuration:
Use the FlySpark app for ESC configuration settings.

ESC Firmware Update:
Follow the provided steps to update the firmware for ESC.

FlySpark F4 V1 BLS 60A Stack

Specs Overview

Package

• FlySpark F4 V1 Flight Controller x 1
• FlySpark BLS 60A 4-in-1 ESC x 1
• 35V 1000uF Low ESR Capacitor x 1
• M3 Nylon Nut x 4
• SH 1.0mm 25mm-length 8pin Cable(for FC-ESC connection) x 1 SH 1.0mm 75mm-length 6pin Cable* x 1
• M3*30mm Iner-hexagon Screws x 4
• DJI 6pin Cable(80mm) x 1
• XT60 Power Cable(100mm) x 1

FC Connection diagram

Guide to FC & ESC Connections

Method 1:

• Using 8.Pin JST Cable

Method 2:

Direct Soldering

• Solder 8 wires to the 8 pads on each end, following the pad definitions below

Flight controller specs

• Use 6-pin cable comes with the O3 Air Unit
• Use 6-pin cable comes with the FlySpark F4 V1 BLS 60A Stack

F C Firmware  update
To update the firmware for your FlySpark F4 VI flight controller, please follow these steps:
Connect the Flight Controller to Your PC:

• Use a USB cable to connect the FlySpark F4 VI flight controller to your PC

Open Betaflight I INAV Configurator.

• . Launch the Betaflight Configurator or INAV Configurator on your PC. For this guide, we’ll use Betaflight Configurator as an example.

Navigate to Firmware Flashing:

• In the Betaflight Configurator, navigate to the ‘Firmware Flashing’ page.

Select Target and Flash Firmware:

•  Choose the target firmware for ‘Flyspark F4 VI’ from the dropdown menu.
• Initiate the firmware flashing process.

Note:
The Flyspark F4 VI flight controller does not support wireless firmware flashing. It must be  performed using a USB connection to your PC.

Flyspark BLS 60A 4-in-l ESC

Connection with Motors & Power Cable

ESC Specs FlySpark F4 V1 BLS 60A Stack

ESC Firmware Update
This 8-bit 50A ESC comes pre-loaded with BLHeliS firmware but can also be flashed to Bluejay firmware, offering RPM filtering and Bi-directional Dshot support. Follow these steps to update the firmware:

1. Prepare Your Drone:
   Remove all propellers from your drone for safety.
2. Connect ESC to Flight Controller:
   Ensure the flight controller is properly connected to the ESC, then power up the drone. This step ensures the ESC initializes correctly.
3. Connect to PC:
   Use a USB Type-C cable to connect the flight controller to your computer.
4. Access Firmware Configuration:
   Open the Chrome browser and visit: www.esc-configurator.com
5. Flashing Steps:
   Follow the firmware flashing steps displayed on the configurator website. Ensure you select the appropriate options for flashing to Bluejay firmware.

CAUTIONS:

• PROPELLERS OFF: REMOVE ALL PROPELLERS.
• SECURE CONNECTION: ENSURE SECURE ESC CONNECTION.
• FOLLOW STEPS: FOLLOW FLASHING INSTRUCTIONS CAREFULLY.
• STABLE POWER: ENSURE STABLE POWER SUPPLY.
• www.FlySpark.in

FAQs