FLYSKY FS-G7P+ Surface Radio with Receiver User Guide

FS-G7P+ Surface Radio with Receiver

Specifications

  • Product Model: FS-G7P+
  • Manufacturer: Flysky
  • Website: www.flysky-cn.com
  • Battery Requirement: 4 AA batteries or 2S lithium battery
  • Ports: USB Type-C Port, JST Port

Product Usage Instructions

Precautions

When using the product, please adhere to the following
precautions:

  • Avoid operating near radio control activity areas, people,
    roads, passenger boats, power lines, or communication
    antennas.
  • Avoid touching hot engine parts immediately after use to
    prevent burns.

Transmitter Overview

The transmitter features various components including keys,
switches, display, steering wheel, knobs, and ports. Familiarize
yourself with the functions of each component.

Basic Operations of the Transmitter

  1. Installing Batteries:
  2. For AA Batteries:

    1. Open the battery compartment cover and insert 4 AA batteries
      following the polarity markings.
    2. Replace the cover securely.

    For Lipo Batteries:

    1. Open the battery compartment cover and insert 2S lithium
      batteries with correct polarity.
    2. Connect the battery cables to the JST Jack and replace the
      cover.
  3. Power On:
  4. To power on the transmitter, ensure batteries are installed
    correctly and toggle the Power Switch to ON. LED indicator will
    light up.

  5. Binding:
  6. If rebinding is required, follow the steps to put the
    transmitter into bind state and connect the power cable to the
    receiver’s BVD/VCC connector for binding.

Frequently Asked Questions (FAQ)

Q: Can I use rechargeable AA batteries with this
transmitter?

A: Yes, you can use rechargeable AA batteries as long as they
are fully charged and compatible with the transmitter.

Q: How do I know if the transmitter is properly bound to the
receiver?

A: When successfully bound, the receiver LED will flash slowly.
Ensure proper connection during binding process.

“`

Quick Start Guide

FS-G7P+

www.flysky-cn.com Copyright © 2025 Flysky Technology Co., Ltd.

Thank you for purchasing the products of Flysky! To find out more about our products, visit our website at www.flysky-cn.com. If you encounter any problems during using, please refer to the manual first. If the problem is still not resolved, contact your local dealer directly or contact the customer service staff via Flysky official website.
Precautions
Read the safety messages listed below before operation! · Do not use the product at night or during bad weather conditions, like
rain or thunderstorms. It can cause erratic operation or loss of control. · Do not use the product when visibility is limited. · Do not expose the product to rain or snow. Any exposure to moisture
(water or snow) may cause erratic operation or loss of control. · Interference may cause loss of control. To ensure the safety of you and
others, do not operate in the following places:

Near any sites where other radio control activity may occur

Near people or roads

On any pond/ lake when passenger boats are present

Near power lines or communication broadcasting antennas

· Do not use this product when you are tired, uncomfortable, or under the influence of alcohol or drugs. Doing so may cause serious injury to yourself or others.
· The 2.4GHz radio band is limited to line of sight. Always keep your model in sight as a large can block the RF signal and lead to loss of control.
· Never grip the transmitter antenna during operation. It significantly degrades signal quality and strength and may cause loss of control.
· Do not touch any part of the model that may generate heat during

operation, or immediately after use. The engine, motor, may be very hot and can cause serious burns.
· Misuse of this product may lead to serious injury or death. To ensure the safety of you and your equipment, read this manual and follow the instructions carefully.
· Make sure the product is properly installed in your model. Failure to do so may result in serious injury.
· Make sure that the receiver’s battery is disconnected before turning off the transmitter. Failure to do so may lead to unintended operation and cause an accident.
· Ensure that all servos operate in the correct direction. If not, adjust the direction first.
· Make sure that the model stays within range in order to prevent loss of control.
CAUTION!
· RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS.

Transmitter Overview

SW1 Key

VR1 Konb

TR (Five-way switch): TR_X: Left and right, and trim of preset direction; TR_Y: Front and rear, and trim of preset throttle; TR_Z: Press operation, reserved switch- key;

Display

CH1 (Steering Wheel) Ambient LED

Five-way switch (Menu Navigation Button): Upward (UP); Downward (DOWN); Right (ENTER); Left (BACK); Middle (OK)

VR2 (Three-position knob) Power supply switch
SW3 (Three-position toggle switch) TR1 (Function adjustment) SW2 (Tact switch/key)
Fixed port for the holder of a mobile phone

CH2 (Throttle trigger)
Battery box: four AA batteries, compatible with the placement of lithium batteries.
USB Type-C Port: Firmware upgrade, USB emulator, and system power supply

JST Port: For power supply through 2s lithium battery.

Basic Operations of the Transmitter
Install the AA Battery Follow the steps below to install the AA batteries: 1. Open the battery compartment cover as
illustrated. 2. Insert 4 fully-charged AA batteries
into the compartment. Make sure that the batteries are well set according to the polarities marked on the battery compartment. 3. Replace battery compartment cover.
Install the Lipo Battery Follow the steps below to install the lithium batteries: 1. Open the battery compartment cover. 2. Insert 2S fully-charged lithium batteries
into the compartment. 3. Plug the cables of lithium batteries into
the JST Jack.Make sure to connect correctly according to the polarities marked on the battery compartment. 4. Replace battery compartment cover.

Press to slide the cover as illusrtated. Then remove the cover.
1. Don’t overcharge or over discharge the lithium battery.
2. Read the instruction of the lithium battery carefully before using.
For safety, power on the transmitter first, then the receiver.

Power on
Follow the steps below to turn on the transmitter: 1. Check to make sure that the batteries are fully charged and installed
correctly. 2. Toggle the Power Switch to the ON position. The LED indicator will
turn light.
Binding
The transmitter and the receiver have been pre-bound before delivery. If you are going to use another receiver, follow the steps below to rebind. The transmitter supports two-way binding and one-way binding. And the default is ONE WAY binding, the steps are as below:
1. Power on the transmitter, then select RX SET > BIND SET > STRAT to put the transmitter into bind state.
2. Connect the power cable to the BVD/VCC connector on the receiver. At this time, the receiver LED flashes slowly.
3. Press and hold the BIND button on the receiver for more than 3 seconds or press and hold the BIND key on the receiver for power-on.
4. After the receiver LED becomes slow flashing, then manually put the transmitter to exit the binding state. At this time, the receiver LED is solid on indicating the binding is successful.
5. Verify that the transmitter and receiver are working properly. If you need to re-bind, repeat the above steps.
Notes:
1. If TWO WAY mode is selected at the transmitter side, when the receiver LED status changes from fast-flashing to solid-on, the binding is successful.
2. The procedure is applicable to the bind between only FS-G7P+ transmitter and FS-R11P receiver. The bind methods vary with receivers. For details about the operations, you can visit the FLYSKY official website to obtain the receiver manual or other related information.

Stick Calibration
The calibration is required in case of data offset of the transmitter due to physical wear in long-term operations. At this time, we need to calibrate the output data and neutral angle of the traversing steering wheel, throttle trigger, VR1 and VR2.
The transmitter has been calibrated at the factory. If you need to recalibrate it, please follow the steps below to perform the settings:
1. Power on the transmitter, enter the system menu, and select the stick calibration function. Follow the prompts to press the Start key for calibration.
2. Swing the steering wheel and trigger to the maximum and minimum travel in each direction respectively and then release them. Turn VR1 to its maximum and minimum travel and then back to the neutral position. Toggle the VR2 left and right repeatedly to the maximum extent for two or three times. Finally, toggle the VR2 back to the neutral position.
3. Press the return key to exit the calibration interface. The calibration is complete.
· If the pop-up window indicates that the calibration has failed, it means that the control to be calibrated has not reached the maximum and minimum travel, or VR1 and VR2 has not been toggled to the middle position. The re-calibration is required.

Failsafe
The failsafe function is used when the receiver loses radio signal and is out-of -control. The receiver performs channel output according to the set failsafe value to protect the safety of the model and personnel.
RESPONSE TIME
Used to set the failsafe judgment time, the setting range is from 250ms to 1000ms. The default is 300ms.
Function settings: Press the OK key to enter the edit state, then set the failsafe judgment time by pressing the UP/DOWN key. After the settings are completed, just press the back key.
For i-BUS/PPM/PWM signal. It can be set to Not Set, OFF or ON.
Not Set: The failsafe has not been set, and there is no output in case of out-of-control.
OFF: It is no output for i-BUS/PPM/PWM channel.
ON: i-BUS/PPM/PWM channel output respectively the set value. Namely, you can set a value respectively for each channel from 1 to 10. By default, this value is the reading of current channel output value.
Function settings:
1. In the FAILSAFE menu, select [I-BUS/PPM/PWM: NOT SET] by pressing the UP/DOWN key;
2. Press the OK key to enter the edit state, then select [ON], the system will pop up a prompt interface, then adjust the corresponding controls to the desired positions and hold them if needed. Select [OK] on the pop-up prompt interface, all channel failsafe value settings have been completed.
3. To set an individual channel, select the channel to be set, press the OK key to enter the edit state.
4. Select the appropriate value or adjust the corresponding control to the desired position and hold it, just press the back key.

Notes:
1. Because the S.BUS signal information contains failsafe flag bits, the failsafe information can be transmitted to the subsequent devices by the failsafe flag bits ruther than by no output state. The subsequent devices gives response according to the analysed information for the failsafe flag bits.
2. For the signal PWM/PPM/i-BUS without failsafe flag bits, it supports the setting of the output signal to OFF in case of failsafe, transmitting the failsafe information to the subsequent devices by no output state.
3. It is No Set by default, then the receiver will not output when RC signal is lost.
Power Off
Follow the steps below to turn off the transmitter:
1. Turn off the receiver first.
2. Toggle the transmitter’s Power Switch to the OFF position to turn off the transmitter.
Make sure to disconnect the receiver power before turning off the transmitter. Failure to do so can result out of control. Unreasonable setting of the Failsafe may cause accidents.

Firmware Update
To put the transmitter into updating state. In case of updating the firmware of the transmitter, use this function to put the transmitter into updating mode first, then upgrade the transmitter’s firmware.

Warning

· Do not unplug the USB Type-C cable while the firmware is updating.

This firmware can be updated via the following two ways.
· The firmware of this transmitter can be updated through the Flysky Assistant (The firmware of Flysky Assistant is available on the Flysky official website www.flysky-cn.com).
· Or update it by following the steps below:
1. Download and open the latest official firmware.
2. Connect the transmitter to the computer via the USB Type-C cable.
3. Go to Home > Main Menu > SYSTEM SET, and select TX Firmware Update, then short press the Middle button of the Five-way switch, a prompt screen will pop up, then select OK, and short press the Middle button to enter updating state.
4. After completing the above steps, click Update in firmware window on the computer to start the update.
5. The transmitter will power on again when the updating process is finished. Then remove the USB Type-C cable and close the firmware.

· After a firmware update the receiver may not be

Attention

connected. If this is the case the receiver firmware

needs to be updated.

Receiver Overview

[16] [8] [15] [7] [14] [6] [17] [13] [12] [5] [4] [11] [3] [18] [10] [2] [9] [1] [19][20] [21] [1] CH1/P(PWM/PPM) [2] CH2 [3] CH3 [4] CH4 [5] CH5 [6] CH6 [7] BIND Connector [8] VCC/BVD (Power Supply/
Battery Voltage Connector) [9] CH7
[10] CH8
[11] CH9 [12] CH10 [13] CH11 [14] SENS Connector [15] SERVO Connector [16] LED [17] Antenna [18] BIND Button [19] Signal Pin
[20] “+” (Connect to Battery Anode)
[21] “-” (Connect to Battery Cathode)

Receiver Firmware Update The FS-R11P receiver firmware update should be done through FlySkyAssistant (only supported by version 3.0 and later, FlySkyAssistant firmware can be got from the official website www.flysky-cn.com). This receiver fimware can be updated via the following two ways: Mode : After the binding between the transmitter and the receiver (the LED of the receiver is solid on), connect the transmitter to the computer, then open the FlyskyAssistant on the computer to update the firmware. Mode : Connect the transmitter to the computer. Then put the receiver to enter the forced update mode by referring to the following three ways (The LED of the receiver operates in three-flash-one-off manner repeatedly). Afterwards, open the FlyskyAssistant on the computer to update the firmware. There are three ways to put the receiver into the forced update state: · Power on the receiver while pressing and holding the BIND button for
more than ten seconds, until the LED of the receiver operates in threeflash-one-off manner repeatedly, then release the BIND button. · Power on the receiver first, then press and hold the BIND button for more than ten seconds, when the LED of the receiver operates in threeflash-one-off manner repeatedly, then release the BIND button. · Connect the signal pins of the CH5 and BIND by using the binding cable, then power on the receiver. Note: the way of entering the forced update state may vary for the receivers. Please refer to the manual of the specific receiver.
· For more information, please read the full user manual.

Specifications
The Specifications of the Transmitter
· Product Model: FS-G7P+ · Adaptive Receiver: Receivers with ANT protocol, such as FS-R11P · Adaptive Models: Cars, boats. · Number of Channels: 10 · Reception Sensitivity: -99dBm · RF: 2.4GHz ISM · Maximum Power: < 20dBm (e.i.r.p.) EU · RF Protocol: ANT · Resolution: 4096 · Low Voltage Alarm: AA battery: <4.2V/ 2S Lipo battery: <7.2V · Data Connector: USB Type-C · Antenna: Built-in single coaxial cable antenna · Input Power: 4 ~ 9V/DC · Battery: 1.5AA*4/2S Lipo · Distance: 300m (Ground distance without interference) · Display: 128*64 LCD (Black and white dot matrix screen) · Firmware Update: Supported · Temperature Range: -10 ~ +60 · Humidity Range: 20% ~ 95% · Dimensions: 136.4*111.8*197.5mm · Weight: 305g · Charging Jack: No · Certifications: CE, FCC ID: N4ZG7P00

Certifications
FCC Compliance Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Warning: changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: — Reorient or relocate the receiving antenna. — Increase the separation between the equipment and receiver. — Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. — Consult the dealer or an experienced radio/TV technician for help.
EU DoC Declaration
Hereby, [ShenZhen FLYSKY Technology Co., Ltd.] declares that the radio equipment type [FS-G7P+] is in compliance with Directive 2014/53/EU.

The full text of the EU DoC is available at the following internet address: www.flyskytech.com/info_detail/10.html
RF Exposure Compliance
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 centimeters between the radiator and your body.
Environmentally Friendly Disposal
Old electrical appliances must not be disposed of together with the residual waste, but have to be disposed of separately. The disposal at the communal collecting point via private persons is for free. The owner of old appliances is responsible to bring the appliances to these collecting points or to similar collection points. With this little personal effort, you contribute to recycle valuable raw materials and the treatment of toxic substances.
CAUTION RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS
FCC ID: N4ZG7P00

www. flyskytech.com.

·
· ·
·

·
· 2.4GHz
·

·
·
· ·
· ·

SW1

VR1

TR TR_X TR_Y TR_Z–

CH1 LED

UPDOWNENTER; BACKOK

VR2
SW3 TR1
SW2 /

CH2
AA
USB Type-C USB

JST 2S

AA AA 1. 2. 4
3.
Lipo 1. 2. 2S 3. JST
4.

1.
2.

1. 2. [ON] LED

1.
2. BVD/VCC 3. BIND 3 BIND
LED 4. LED LED
5.
1. LED
2. FS-G7P+ FS-R11P
FLYSKY

VR1 VR2
1.
2. VR1 VR2 VR2
3.

VR1 VR2

250ms~1000ms 300ms
UP/DOWN
i-BUS/PPM/PWM [ ][ ] [ ] [ ] [ ] i-BUS/PPM/PWM [ ] i-BUS/PPM/PWM 1~10
1. UP/DOWN [I-BUS/PPM/PWM ] 2. UP/DOWN [ ] [ ] 3.
4.
1. S.BUS ”
” [ ] 2. PWM/PPM/i-BUS [ ] [ ] “” ; 3. [ ]

1. 2. [OFF]

·

USB Type-C

· “” www. flyskytech.com

·

1.
2. USB Type-C
3. > >[ ] [ ] [ ] 4. [Update] 5. USB Type-C

·

,

FS-R11P

[16] [8] [15] [7] [14] [6] [17] [13] [5] [12] [4] [11] [3] [18] [10] [2] [9] [1] [19][20] [21] [1] CH1/P(PWM/PPM) [12] CH10 [2] CH2 [13] CH11 [3] CH3 [14] SENS [4] CH4 [15] SERVO [5] CH5 [16] LED [6] CH6 [17] [7] [18] [8] VCC/BVD( [19] S / ) [9] CH7 [20] “+” [10] CH8 [21] “-” [11] CH9

FS-R11P FlySkyAssistant 3.0 www.flyskytech.com LED LED · LED
· LED
· BIND CH5

· FS-G7P+

· FS-G7P+ · ANT FS-R11P · · 10 · -99dBm · 2.4GHz ISM · < 20dBm · ANT · 4096 · AA : <4.2V: 2S Lipo : <7.2V · 1.5AA*4 2S Lipo JST · USB Type-C · · · 4~9V/DC · LCD 128*64 · · 300m( ) · -10 +60 · 20% 95 · 136.4*111.8*197.5mm · 305g · CEFCC ID: : N4ZG7P00
Figures and illustrations in this manual are provided for reference only and may differ from actual product appearance. Product design and specificatiions may be changed without notice.

FCC ID: N4ZG7P00
Http://www.flysky-cn.com Copyright © 2025 Flysky Technology Co., Ltd.
Release Date: 2025-03-12
Manufacturer: FLYSKY Tech Co.,Ltd Address: 16F Huafeng Building, Futian District, Shenzhen, China.

Documents / Resources

FLYSKY FS-G7P+ Surface Radio with Receiver [pdf] User Guide
G7P00, N4ZG7P00, FS-G7P Surface Radio with Receiver, FS-G7P, FS-G7P Radio with Receiver, Surface Radio with Receiver, Radio with Receiver, Radio, Receiver

References

Leave a comment

Your email address will not be published. Required fields are marked *