Fluance HFHTB Signature Hi-Fi Surround Sound USER GUIDE

MIDRANGE: 5 Inch Woven Glass Fiber Butyl Rubber Surrounds Separate Enclosures
WOOFER: Dual 8 Inch Polypropylene Butyl Rubber Surrounds Separate Enclosures

POWER HANDLING: 90 – 200 Watts
FREQUENCY RESPONSE: 35hz – 20khz

SENSITIVITY: 89 Db @ 2.83v / 1m
CROSSOVER FREQUENCY: 530/2600 Hz – Pcb

MOUNTED CIRCUITRY IMPEDANCE: 8 Ohm Compatible
ENCLOSURE: Tuned Rear Port Bass Reflex Tower Design Dampened

DIMENSIONS:24 x 10.9 x 15.4 Inch
SPEAKER WEIGHT:4 Pounds/Speaker

SERIES: Signature

SIGNATURE HIFI 2-WAY BOOKSHELF SURROUND SOUND SPEAKERS SPECIFICATIONS

SPEAKER CONFIGURATION: 2 Way – 2 Driver Surround Speaker (Wall Mountable)

TWEETER: 1 Inch Neodymium Balanced Silk Dome Ferrofluid Cooled
WOOFER: 5 Inch Glass Fiber Treated Butyl Rubber Surrounds

POWER HANDLING: 30 – 120 Watts
FREQUENCY RESPONSE: 60hz – 20khz

SENSITIVITY: 85 Db @ 2.83v / 1m
CROSSOVER FREQUENCY: 2300hz Phase Coherent

IMPEDANCE: 8 Ohm Compatible
ENCLOSURE: Dual Tuned Front Port Bass Reflex Design

DIMENSIONS:8 x 7.87 x 8.22 Inch Speaker
WEIGHT:7 Pounds/Speaker

SERIES: Signature
SPEAKER TYPE: Bookshelf

SIGNATURE HIFI 2-WAY CENTER CHANNEL SPEAKER SPECIFICATIONS

SPEAKER CONFIGURATION: 2 Way – 3 Driver Center Speaker (Wall Mountable)
TWEETER: 1 Inch Neodymium Balanced Silk Dome Ferrofluid Cooled

WOOFER: Dual 5 Inch Glass Fiber Treated Butyl Rubber Surrounds
POWER HANDLING: 40 – 120 Watts

FREQUENCY RESPONSE: 60hz – 20khz
SENSITIVITY: 92db @ 2.83v / 1m
CROSSOVER FREQUENCY: 2300 Hz Phase Coherent
IMPEDANCE: 8 Ohm Compatible
ENCLOSURE: Dual Tuned Rear Port Bass Reflex Design
DIMENSIONS:28 x 18.9 x 10.6 Inch
SPEAKER WEIGHT:3 Pounds/Speaker
SERIES: Signature

Grab the drinks and popcorn, and then take a seat. The film is about to start. Dark, silent room eventually comes to life as lights lower. The words “watch out!” are shouted. Your heart starts to beat rapidly as you hear gunshots behind you and see a plane flying overhead. When the moment is through, you relax, glance around, and smile as you cling to the chair’s arm in anticipation. It is your house.

Introduction

Thank you for your purchase of your Fluance product. We hope you enjoy your experience. If you have any questions please visit us at: www.fluance.com/support

Fluance believes everyone should experience audio in its truest form, recreating the performance the way the artist intended. Utilizing only superior components and expert audio engineering, their products are a testament to the performance that can be achieved when a passion for music takes center stage. The perfect complement to any audiophile’s lifestyle, you’ll be enjoying live performances in your home for years to come.

Online Resources

For videos on the full setup and configuration of your speakers visit us at: www.fluance.com/resources

Speaker Basics

Surround Sound Speaker Setup

Speaker placement is the most important part of any Home Theater setup. The proper placement will optimize surround sound and performance of your Fluance speaker system.

Surround System

Five audio channels: Front Left, Front Right, Center, Left Surround, Right Surround and the Subwoofer.

Surround System

Seven audio channels: Front Left, Front Right, Center, Left Surround, Right Surround, Back Left & Right Speakers, and the Subwoofer.

Wiring Guide

Setting up a home theater system requires proper wiring and wire manage-ment. Depending on the system you set up, the size of the wires and the prop-er type of wiring you need may vary. Fluance recommends 18 gauge or better wire for optimal sound quality.

Standard Method

Cut insulation of lead wire to reveal 0.39 – 0.78 inches (1-2cm) of exposed wire on both ends.

Rotate the positive and negative terminal on the back of the speaker counter clockwise to unlock.
Insert positive/negative end of exposed wire into unlocked positive/negative terminal of speaker.
Rotate positive and negative terminals clockwise to lock exposed wire into terminal.

Insert positive/negative exposed wire of other end into positive/negative terminal of receiver amplifier.

Banana Plug Method

Cut insulation of lead wire to reveal 0.39 – 0.78 inches (1-2cm) of exposed wire on both ends.
Rotate the positive and negative ends on the back of banana plug counter clockwise to unlock.

Insert positive/negative end of exposed wire into now unlocked middle bracket of banana plug and rotate clockwise to lock.
Insert positive/negative front ends of banana plug into positive/negative speaker terminals.
Insert positive/negative exposed wire of other end into positive/negative terminal of receiver amplifier.

Bi-Amp Connection

Bi-amping

Bi-amping involves the use of two separate amplifier channels per speaker, one to connect to each pair of binding posts. It is only possible when speakers have two or more sets of binding posts. Benefits include: transients are less likely to cause amplifier overload (clipping) and/or speaker damage, reduced distortion, and better matching of the power amplifier to speaker drivers.

Here are the steps to connect speakers in the bi-amplification mode:

Ensure that your system is powered OFF.
Remove the bi-wire bridges from each speaker (this separates the low pass filter & high pass filter crossovers).
Connect each amplifier channel to its respective speaker section as shown.

Set the level controls on the amplifiers such that the signal will arrive at all speaker terminals at the same power-volume level. If your amplifiers are identical, it is usually sufficient to set all the amplifier level controls the same. The speaker’s built-in crossovers are designed to match the efficiency of all the individual drivers (tweeters, midranges, and woofers) When using the bi-amplifier connection you must directly deal with some of these issues by adjusting levels according to your listening preference.

Bi-Wire Connection

Bi-wiring

In bi-wiring, each loudspeaker has two pairs of connectors and two cables are run from the same amplifier output to the speaker cabinet – one for the high frequency or tweeter driver and one for the low frequency driver (through two separated crossover filters). The purported advantage of this split is that it reduces magnetic interaction in the cable, resulting in a better soundstage.

How to connect speakers in the bi-wire mode

Ensure that your system is powered OFF.
Remove the bi-wire bridges from each speaker (this separates the low pass filter & high pass filter crossovers).

Connect each amplifier channel to its respective speaker section as shown.

Take care to maintain the correct polarity when connecting (+ or RED) to (+ or RED) and (- or BLACK) to (- or BLACK). Before attempting the connection make sure that your amplifier’s speaker wire connectors will accept a second set of cables and that the equipment is turned OFF while you make the connections.

Turntable and Passive Speaker Setup

To connect passive speakers to a turntable additional electronics are needed. The standard configuration includes the turntable, a phono preamplifier, an amplifier, and a pair of passive speakers.

Amplifier

An amplifier is the most important electronic when using passive speakers. The amplifier provides the power to drive the speakers. Some integrated amplifiers have a Phono input that uses a built-in preamplifier. An AV Receiver, with a built-in amplifier, can also be used.

Phono Preamplifier

A preamplifier boosts a small electrical signal to a normal line level, preparing the signal for further amplification. A phono preamplifier is specifically designed to amplify the signal from a turntable.

Turntable

The connected turntable may feature an internal preamplifier. The built-in preamplifier should be disabled or bypassed if using an external preamplifier or a receiver with a built-in preamplifier.

IMPORTANT! Only one preamplifier should be used in a turntable setup. If your turntable/amp features an internal preamplifier you must not use a second preamplifier. Using more than one preamplifier can damage any connected devices.

Grounding

All components in a turntable setup should be properly grounded. Connect a ground wire from your turntable to your preamplifier and then to your amplifier. This will prevent unwanted interference or humming during playback.

Placement

Incorrect speaker placement can cause unwanted feedback on turntable setups. To avoid feedback follow the below recommendations:

Bookshelf speakers should not be on the same surface as the turntable.
The speakers can also be placed on speaker stands or speaker isolation pads.
The turntable should be on a solid and sturdy surface.

Wall Mounting Recommendations

Whether you are mounting a TV, speaker, or on-wall shelving, it’s always best to anchor into a stud. Drywall anchors can work well, but you never really know the quality of drywall. There may be cracks hidden under paint and texture. There may have been water damage, or it may simply pull off the wall if poorly installed. Because of these potential problems, it’s safest to hit a stud.

Stud Finding Tips

Most homes are built with 16″ on-center studs, which means there should be a stud every 16″. If you have trouble finding studs on a wall, verify how far apart they are in the home by locating and measuring them on another wall.
When using a stud finder, use painters’ tape to mark out at least three studs in a row, then measure the distances between the studs. If the studs are equidistant apart, you can be sure the stud finder actually marked studs, as opposed to some other object in the wall.

Care & Maintenance

Refrain from touching the tweeter dome; if the tweeter is pushed in the sound quality will be affected tremendously. The dispersion and response of the tweeter is dependent on its shape.

Ensure positive/negative speaker wire does not touch; this can lead to blowing a fuse or shorting out your amplifier/home theater receiver.
Refrain from dragging floor-standing speakers across the floor when floor spikes are attached as it is possible that surfaces can be scratched and/or damaged.
Clean your speakers regularly with a dry microfiber cloth and do not use any liquid cleaners or they might cause damage to the amplifiers.

Do not keep speakers on metals conducive to magnetism; you can use wooden materials to stand them on, or any non-magnetic one. Do not keep it near any magnetic source or the built-in electromagnet may be damaged.
Static electricity is one of the hazards that can affect your electrical systems. Please take necessary steps to avoid your speakers coming into contact with static electricity.
Keep speakers away from direct sun rays.

If there is a port/vent on the speaker, avoid blocking the ventilation.
It is recommended to keep the speakers 2-3 feet away from any obstructions.
It is recommended that the amplifier is connected to a functional clean power outlet or surge protector.

Avoid running speaker wire parallel to electrical lines to avoid interference.

Troubleshooting

Audio Distorted

Too much or too little power from amplifier/receiver.

Lower the volume and adjust equalizer settings to avoid excessive bass.

Buzzing/Crackling

Check cable connections at the receiver and speaker binding posts.

Plug the receiver directly into a wall. Where possible use a different outlet.
Try different audio sources (TV, Smartphone, Gaming Console, Blu-ray/DVD player).

Muddy/Muffled Bass

Speakers are not broken in. Allow a minimum 10 hours of regular use for proper break-in.
Speakers/Subwoofer too close to walls. Allow 2-3 feet behind speakers for proper airflow.
Adjust equalizer settings on the receiver.

No or Limited Bass

Check cable connections at the receiver and speaker binding posts.
Tower speakers with two sets of binding posts use bridge pins or plates to connect the top and bottom posts when you are not bi-amping. If these are missing, only one set of drivers will work.

Change channel settings on the receiver. If a subwoofer is enabled on the receiver without one connected, the bass frequencies will not come through the front speakers.

General Speaker Troubleshooting

Confirm the speaker wires are connected to the matching binding posts (Black to Black, Red to Red).

Check that the speaker wire is in good condition.
Speaker wire should be 18 AWG (American Wire Gauge) or better.
Ensure the binding posts are fully tightened.

If using speakers with multiple binding posts on back, confirm the metal bridge pins/plates are in place.
Compare the amplifier power output to the speaker power handling to ensure they match.
Eliminate any audio equalizers or filters that may affect audio output.

Videos

Fluance creates videos on many subjects related to our products. If you wish to learn more about choosing a home audio receiver or setting up your home theatre speakers, you can watch these videos and more at: www.fluance.com/videos

Knowledge

Fluance’s Support Center is designed with you in mind. These tips and articles have been written by Fluance industry experts to help you optimize your home theater system.

Visit us online to learn more: blog.fluance.com/knowledge

The Ultimate Guide to Home Theater Setup

Achieving great sound in a home entertainment system is inherently more complex than with stereo systems, because there are six to twelve (or more) speakers to set up, rather than just two. No matter what speaker configuration you choose, our guide to home theater surround sound setup will help you place and configure your speakers for the best possible sound.

Guide: blog.fluance.com/home-theater-setup-guide

How to Set the Phase and Crossover Frequency on Your Subwoofer

Setting your bass management on processors, receivers, and the subwoofer is critical if you hope to get the best performance out of your audio system. Check out our guide on configuring your subwoofer for the best performance.

Guide: blog.fluance.com/set-phase-crossover-frequency-on-subwoofer

Matching Speaker and Receiver Power

It is best to have an amplifier that slightly exceeds the power of the speakers that are connected to it. For example, a 30-watt RMS rated amplifier at high volume will cause clipping and distortion when connected to a speaker with 100 watt RMS. This will produce harmful electronic signals that will potentially damage your speakers. It is also important that your amplifier not be too much higher than the power of the speakers. Use the guide below to learn more about power ratings, impedance, and sensitivity.

Guide: blog.fluance.com/matching-speaker-and-receiver-power

Medium-density fibreboard (MDF) vs Natural Wood

Have you ever heard of the expression “no two snowflakes are alike”? Well the same can be said for natural wood speakers. Natural wood often has organic characteristics like knots, rings and lines which can affect the way a speaker system looks and sounds. There are 3 main benefits of MDF wood:

Producing great sound in solid construction
Speakers designed with beautiful finishes
A lower cost in construction that saves you money

Warranty Information

Fluance gives the following warranty to the original customer of each new Fluance product purchased from a dealer authorized by Fluance. Fluance warrants that each new product, under normal use, is free from defects, subject to the terms and conditions set forth. If a defect should occur within the warranty period, repairs will be made free of charge for parts and labor when such defects are determined by us to be attributable to faulty materials or workmanship at time of manufacture.

Warranty Period

The Fluance products listed below are warranted for parts and labor for the stated period from the date of original purchase and are subject to the terms and conditions of the warranty.

Home Audio Passive Speakers: Lifetime Warranty

Active/Powered Speakers: 2 Year Warranty

HiFi Turntables: 2 Year Warranty

Warranty Exclusions

Products purchased from a dealer not authorized by Fluance.
Products with the serial number defaced, altered or missing.

Defects resulting from disaster, accident, abuse, misuse, lightning, power surges, neglect, unauthorized modification or water damage.
Defects or damage as a result of repairs performed by a person or party not authorized by Fluance.
Defects or damage occurring during shipping (claims should be made with the shipping company).

Defect or damage as a result of connecting a product to an outlet with the incorrect voltage. Voltage converters must be used where applicable.

To Obtain Warranty Service

Should your Fluance product require warranty service, please contact your Fluance Authorized Dealer and send your product fully insured and freight prepaid to the nearest Fluance authorized service center. Before sending to Fluance, you will be required to get a Return Authorization Number from your dealer.

Products shipped without a valid Return Authorization Number will be refused. To avoid possible shipping damage, make sure the product is properly packaged and well protected. Include a copy of your original bill of sale as proof of warranty along with your name, home and/or work telephone number(s), a complete return address and a detailed description of the faults.

Products repaired within warranty will be returned freight prepaid. This warranty in itself is not considered a valid proof of purchase. When applying for warranty repairs, you must present the original copy of your bill of sale as proof of warranty.

FREQUENTLY ASKED QUESTIONS

What is the break-in period for Fluance speakers?

The break-in period for our speakers is a minimum 10-12 hours of playing time at normal listening volumes. After this period the drivers will have had enough movement to perform at their peak level.

Do I need Banana Plugs for my Fluance speakers?

No, banana plugs are not required. However they can provide the following benefits: They provide a stronger connection and it is more convenient to plug and unplug a banana plug than to screw or clamp bare wire into the binding posts. Check out our Home Audio Accessories section for the banana plugs you may want in addition to your new speaker system.

Why is 18-Gauge Speaker Wire recommended?

At Fluance, we recommend that you use 18-gauge speaker wire when setting up your Home Theater System. We recommend 18-gauge because the larger amount of copper provides less resistance for electricity. A larger gauge (a thinner wire with less copper) can result in power loss, which in turn means lower sound quality and lesser performance from your Home Theater System.

What Receiver should I use with Fluance speakers?

In order to get truly Serious Performance™ from your Fluance Speakers, they must be paired up with a Home Theater Receiver capable of equally Serious Performance. With that in mind, the brand names most often used by Fluance customers are: Denon, Marantz, Onkyo, Yamaha.

What are Sound Isolation Floor Spikes?

Sound isolation floor spikes eliminate vibration absorption to aid in eradicating distortion. Floor spikes will isolate sound that is transmitted through the floor by reducing the speaker surface area in direct contact with the floor. In return the speakers will produce a clearer more defined sound.

What are Sound Isolation Pads?

Sound isolation pads ensure your speakers are isolated from their supported surface, decreasing unwanted vibrations and delivering a tighter bass response and increased clarity. Some isolation pads can also be used to angle the speakers to the ideal listening position.

Do I have to bi-amp or bi-wire my connections with your speakers?

Some of our models have speaker wire connections to allow for bi-amping or bi-wiring. This is for your benefit and can be used to enhance the performance of your system. Connection of a basic audio system, where there is only one connection from the amplifier, is very simple and bi-amp or bi-wire is not necessary. You can connect your speakers using the regular left and right speaker wire connections and ignore the second set of terminals. There are gold-plated bridges connecting the two sets of terminals that allow the speaker to be connected as a traditional loudspeaker. Only remove these bridges if you plan to bi-wire or bi-amp your speakers. See the Bi-Amp Connection and Bi-Wire Connection sections of this manual for more information.

How do I register my speakers?

Your warranty registration is automatic and is processed by us when you place your order directly with us (no additional paperwork required beyond a copy of your invoice). All returns require a return authorization and you will receive complete instructions with the authorization.

Does fluance make good speakers?

It truly is the ideal speaker for every event, as praised by Fluance. We can enjoy excellent sound at our cottage because I retain the original AI60 there. Due to the odd shape of our cottage, there isn’t an ideal location for a two-channel setup. However, the Ai60 functions great in our room.

Are fluance speakers made in Canada?

A Canadian firm called Fluance makes hi-fi music systems, turntables, home theatre speakers, and sound bases. We commemorated our 20th anniversary in 2019 after being founded in 1999! We are situated in Niagara Falls, Ontario, and supply products to customers throughout the world from there.

What is the recommended continuous power for this set? What level of opposition does each speaker exhibit?

Jarred, welcome and thank you for your question. The power handling capacity for these speakers is between 90 and 200 W RMS. We advise contacting us directly through our website, where you may choose between using Live Chat or filling out the online contact form, if you have any more technical questions.

Is an amplifier required for it to play?

Yes, you would need to connect these passive speakers to a home theatre receiver since they are passive speakers.

What are Fluance speakers?

MDF wood is carefully used in the precise construction of Fluance tower speakers to create a warmer, more organic sound. Through two or three way driver configuration, tweeter height alignment, and optimal cabinet design, a broad range of sound is produced.

View Fullscreen

References

User Manual

Fluance HFHTB Signature Hi-Fi Surround Sound

SIGNATURE HI-FI 3-WAY FLOORSTANDING TOWER SPEAKERS SPECIFICATIONS