Johdanto
This manual provides detailed instructions for the proper use, setup, operation, and maintenance of your FOXWELL NT630 Plus OBD2 Scanner. This device is designed to assist in diagnosing issues within your vehicle's Anti-lock Braking System (ABS), Supplemental Restraint System (SRS), and On-Board Diagnostics II (OBD2) systems. Please read this manual thoroughly before operating the device.
Tuotteen ominaisuudet
- ABS Auto Bleed Function: Assists in bleeding air from the ABS braking system to restore proper brake pedal function.
- Comprehensive Diagnostic Capabilities: Diagnoses ABS, SRS, and OBD2 systems. Includes reading and clearing trouble codes, viewing live data streams, and turning off indicator lights.
- Useita nollaustoimintoja: Features ABS Bleed, SRS Reset, SAS Calibration, Oil Light Reset, and Electronic Parking Brake (EPB) Reset.
- Kaksisuuntainen ohjaus: Allows active testing for ABS and SRS systems, including motor tests, actuator tests, and auto bleed tests.
- Automaattinen VIN-skannaus: Automatically identifies vehicle information for quicker diagnostics. Manual VIN entry is also supported.
- OBD II 16-Pin Extension Cable: A 1-meter (39-inch) male-to-female diagnostic extension cable for convenient connection to the vehicle's OBDII port.
Asennus
- Paikanna OBDII-portti: The OBDII port is typically located under the dashboard on the driver's side of the vehicle.
- Skannerin kytkeminen:
Plug the male end of the 16-pin extension cable into the vehicle's OBDII port. Then, connect the female end of the extension cable to the FOXWELL NT630 Plus scanner.
Image: The 16-pin OBD2 extension cable, showing both male and female connectors for connecting the scanner to the vehicle's diagnostic port.
Kuva: Lähikuva view of the male OBD2 connector, which plugs into the vehicle's diagnostic port.
Kuva: Lähikuva view of the female OBD2 connector, where the diagnostic tool is connected.
- Virta päälle: Skanneri käynnistyy automaattisesti, kun se on kytketty ajoneuvon OBDII-porttiin.
- Alkukokoonpano: Follow the on-screen prompts to select language, time zone, and other initial settings.
Käyttöohjeet
General Diagnostics (ABS, SRS, OBD2)
- Select Diagnostic Mode: From the main menu, select the desired diagnostic mode (e.g., "ABS", "SRS", or "OBDII").
- Ajoneuvon tunnistus: The scanner will attempt to automatically identify the vehicle's VIN. If unsuccessful, you may need to enter it manually.
- Lue koodit: Select "Read Codes" to retrieve Diagnostic Trouble Codes (DTCs) from the selected system.
Image: A visual representation of the scanner's interface, highlighting options such as "Read Codes", "Clear Codes", "Freeze Frame", "Live Data", and "Auto VIN" for comprehensive diagnostics.
- Tyhjennä koodit: After addressing the underlying issue, select "Clear Codes" to erase the DTCs and turn off associated warning lights.
- View Live-tiedot: Valitse "Live-tiedot" view real-time sensor data, which can help in diagnosing intermittent issues.
- Pysäytyskehystiedot: Access "Freeze Frame" data to see a snapshot of sensor readings at the moment a DTC was set.
ABS Auto Bleed Function
The ABS Auto Bleed function helps remove air from the brake system, which can cause a soft or sinking brake pedal. This function is vehicle-specific; consult your vehicle's service manual for compatibility and specific procedures.
- Valmistelu: Ensure the vehicle is on a level surface, the ignition is on, and the brake fluid reservoir is at the correct level.
- Access Function: From the ABS menu, select "ABS Auto Bleed" or a similar option.
- Noudata näytön ohjeita: The scanner will guide you through the bleeding process, which typically involves opening and closing bleed screws on the calipers in a specific sequence while the scanner activates the ABS pump.
Image: An illustration detailing the ABS auto bleed process, showing the internal components of a car's braking system and steps for bleeding after replacing the ABS pump or brake oil.
Reset Functions (SAS, Oil, EPB, SRS)
The NT630 Plus offers several reset functions to maintain vehicle systems after repairs or component replacements.
- SAS-kalibrointi: Calibrates the Steering Angle Sensor after replacement or alignment.
Image: An illustration demonstrating SAS (Steering Angle Sensor) calibration, along with icons for Oil/Service Light Reset and EPB (Electronic Parking Brake) Reset functions.
- Öljyvalon nollaus: Nollaa öljynvaihtovalon öljynvaihdon jälkeen.
- EPB-nollaus: Nollaa sähköisen seisontajarrujärjestelmän jarrupalojen vaihdon jälkeen.
- SRS-nollaus: Reads and clears airbag system fault codes. Note: This function cannot clear airbag crash data.
Kaksisuuntainen ohjaus (aktiivinen testi)
Bi-directional control allows the scanner to send commands to vehicle components to test their functionality. This is useful for verifying repairs or diagnosing specific component failures.
- Saatavilla olevat testit: Includes ABS motor test, actuator tests, and auto bleed tests for ABS and SRS systems.
- Toimenpide: Select "Bi-directional Control" from the main menu, then choose the specific test. Follow on-screen instructions carefully.
Image: The FOXWELL NT630 Plus scanner showing its main menu with options for bidirectional control, including "ABS Manual Control Test", "Auto Bleed Test", "ABS Motor Test", and "Actuator Test".
Huolto
- Ohjelmistopäivitykset: Regularly check for software updates on the FOXWELL official website to ensure compatibility with the latest vehicle models and diagnostic protocols.
- Puhdistus: Clean the scanner's screen and casing pehmeällä, damp kangas. Vältä hankaavien puhdistusaineiden tai liuottimien käyttöä.
- Varastointi: Säilytä laitetta kuivassa, viileässä paikassa, poissa suorasta auringonvalosta ja äärimmäisistä lämpötiloista.
- Kaapelihuolto: Inspect the OBDII extension cable for any signs of wear or damage before each use. Replace if necessary.
Vianetsintä
| Ongelma | Mahdollinen syy | Ratkaisu |
|---|---|---|
| Skanneri ei käynnisty. | Loose connection to OBDII port; vehicle ignition off; vehicle battery low. | Ensure secure connection; turn ignition on; check vehicle battery. |
| Viestintävirhe ajoneuvon kanssa. | Incorrect protocol selected; faulty OBDII port; damaged cable. | Verify vehicle compatibility; try another vehicle if possible; inspect cable for damage. |
| Koodien tyhjentäminen ei onnistu. | Perusvika on edelleen olemassa; sytytysvirta ei ole päällä. | Repair the fault first; ensure ignition is on (engine off). |
| ABS Auto Bleed not working. | Vehicle not supported; incorrect procedure followed. | Check vehicle compatibility list; review vehicle service manual for specific steps. |
Tekniset tiedot
- Merkki: FOXWELL
- Malli: NT630 Plus
- PC Operating System (for updates): Windows XP (or later compatible versions)
- Liitettävyys: OBDII 16-Pin
- Toiminnot: ABS, SRS, OBD2 Diagnostics, ABS Auto Bleed, SAS, Oil, EPB, SRS Resets, Bi-directional Control.
Takuu ja tuki
For warranty information and technical support, please refer to the official FOXWELL websivustolta tai ota yhteyttä suoraan heidän asiakaspalveluunsa. Säilytä ostokuitti ostotodistuksena.
Verkkoresurssit: www.foxwelltech.com
