Johdanto
The SUNLU S1 Plus Filament Dryer is designed to remove moisture from 3D printer filaments, which can absorb humidity from the air. Drying filament helps prevent common printing issues such as stringing, clogging, and poor adhesion, leading to improved print quality and smoother model surfaces. This manual provides detailed instructions for the proper use and maintenance of your S1 Plus Filament Dryer.
Tuote loppuview
The SUNLU S1 Plus features a built-in circulation fan for uniform heating, a 2-inch LCD screen for displaying temperature and time, and two control buttons for easy operation. It is compatible with various filament types and diameters.
Figure 1: The SUNLU S1 Plus Filament Dryer, showing the clear lid and control panel.
Tärkeimmät ominaisuudet:
- 360° Hot-air Circulation: Ensures uniform heating and effective moisture removal.
- Helppo käyttö: Two-button control with a clear LCD screen for temperature and time settings.
- Säädettävät asetukset: Customizable drying time (0-24 hours) and temperature (35°C-55°C).
- Laaja yhteensopivuus: Supports 1.75mm, 2.85mm, and 3.00mm filament diameters.
- Hiljainen toiminta: Operates quietly, less than 10dB.
- Print While Drying: Designed with rollers to allow filament to be used directly from the dryer during printing.
Asennusohjeet
- Pura kuivausrumpu pakkauksesta: Carefully remove the SUNLU S1 Plus Filament Dryer and all accessories from its packaging. Ensure all components are present: the dryer unit, power adapter, and user guide.
- Liitä virta: Insert the power adapter cable into the power port located at the back of the dryer unit. Plug the power adapter into a standard electrical outlet.
- Lataa filamentti: Open the transparent lid of the dryer. Place a spool of 3D printer filament onto the rollers inside the dryer. Ensure the filament unwinds smoothly.
- Sulje kansi: Sulje läpinäkyvä kansi kunnolla.
Figure 2: Visual guide for initial setup and operation steps.
Käyttöohjeet
The S1 Plus features a simple two-button interface for setting drying parameters.
Figure 3: Control panel layout with LCD screen and buttons.
- Virta päälle: Press the left button to turn on the device. The LCD screen will illuminate, displaying the current temperature and default drying time.
- Aseta lämpötila:
- Press and hold the left button to enter temperature setting mode. The temperature value will flash.
- Use the left and right buttons to adjust the desired drying temperature between 35°C and 55°C.
- Press the left button again to confirm the temperature setting.
- Aseta kuivumisaika:
- Press and hold the right button to enter time setting mode. The time value will flash.
- Use the left and right buttons to adjust the desired drying time between 0 and 24 hours.
- Press the right button again to confirm the time setting.
- Aloita kuivaus: Once temperature and time are set, the dryer will begin the drying process automatically. The LCD will display the current temperature and remaining time.
- Stop Drying: To stop the drying process before the timer expires, press and hold the left button until the display turns off.
Recommended Drying Temperatures and Times:
The following table provides general recommendations. Optimal settings may vary based on filament brand, age, and ambient humidity.
Figure 4: Recommended drying settings for common filament types.
| Materiaali | Kuivauslämpötila | Kuivumisaika |
|---|---|---|
| PLA | 45-50 °C | 3-6 tuntia |
| PLA Plus | 45-50 °C | 3-6 tuntia |
| PUU | 45-50 °C | 3-6 tuntia |
| PVB | 45-50 °C | 3-6 tuntia |
| ABS | 50-55 °C | 3-6 tuntia |
| ASA | 50-55 °C | 3-6 tuntia |
| LANTIAT | 50-55 °C | 3-6 tuntia |
| PC | 50-55 °C | 3-6 tuntia |
| PETG | 48-52 °C | 3-6 tuntia |
| TPU | 48-52 °C | 3-6 tuntia |
Huolto
- Puhdistus: Ensure the device is unplugged before cleaning. Wipe the exterior with a soft, dry cloth. Do not use abrasive cleaners or immerse the unit in water.
- Varastointi: When not in use for extended periods, store the dryer in a cool, dry place away from direct sunlight.
- Filamentin säilytys: For best results, store dried filament in airtight containers with desiccant packs to prevent re-absorption of moisture.
Vianetsintä
- Problem: Dryer does not power on.
- Ratkaisu: Check if the power adapter is securely connected to both the dryer and the electrical outlet. Ensure the outlet is functioning correctly.
- Problem: Filament is still wet after drying.
- Ratkaisu:
- Verify that the correct temperature and drying time were set for the specific filament type. Refer to the "Recommended Drying Temperatures and Times" table.
- Increase the drying time or temperature within the recommended range.
- Ensure the lid is properly closed to maintain the internal environment.
- Problem: Display is not working correctly.
- Ratkaisu: Try unplugging the dryer, waiting for 30 seconds, and then plugging it back in to reset the device.
Tekniset tiedot
| Ominaisuus | Yksityiskohta |
|---|---|
| Malli | S1 Plus |
| Merkki | SUNLU |
| Tuotteen paino | 2.2 paunaa (noin 1 kg) |
| Pakkauksen mitat | 11.54 x 10.98 x 4.29 tuumaa |
| Filament Diameter Compatibility | 1.75mm, 2.85mm, 3.00mm |
| Lämpötilan asetusalue | 35–55 °C |
| Ajan asetusalue | 0–24 tuntia |
| Toimiva melu | <10dB |
| Suurin käyttövirta | 1.8A |
| Suurin työteho | 48W |
Takuu ja tuki
The SUNLU S1 Plus Filament Dryer comes with a one-year warranty period. For professional technical support, after-sales service, or any questions regarding your SUNLU Filament Dehydrator Box, please contact SUNLU customer service. They aim to reply to emails quickly during working hours.
Please refer to the official SUNLU webKatso ajantasaisimmat yhteystiedot ja yksityiskohtaiset takuuehdot verkkosivustolta tai ostodokumentaatiosta.
