Cube Acid Pro 80 Bicycle Lighting Set

1. Johdanto

Thank you for choosing the Cube Acid Pro 80 Bicycle Lighting Set. This set, comprising the Acid Pro 80 front light and the Acid Pro rear light, is designed to enhance your visibility and safety during cycling. Both lights are StVZO approved, ensuring compliance with German road traffic regulations, and are splash-proof for reliable performance in various weather conditions. The integrated rechargeable batteries offer convenience, and the tool-free mounting system allows for quick and easy installation.

2. Pakkauksen sisältö

Varmista, että pakkauksessasi on kaikki tarvittavat osat:

• Acid Pro 80 Front Light
• Acid Pro Rear Light
• Micro USB latauskaapeli

Image: The complete Cube Acid Pro 80 Bicycle Lighting Set, featuring the front and rear lights.

3. Asennus ja asennus

3.1. Front Light Installation

The Acid Pro 80 front light features an asymmetrical design and a rod holder with a Slide-Lock attachment system, allowing for central positioning on your handlebars for a clean look. The silicone strap ensures a secure, tool-free mount.

1. Open the silicone strap on the front light's mounting bracket.
2. Position the light centrally on your bicycle handlebars.
3. Wrap the silicone strap around the handlebar and secure it to the hook on the bracket. Ensure the light is firmly attached and does not wobble.
4. Adjust the angle of the light to illuminate the road ahead effectively, without dazzling oncoming traffic.

Kuva: Sivu view of the Acid Pro 80 front light securely mounted on bicycle handlebars.

Kuva: Yläosa view of the Acid Pro 80 front light, demonstrating its central mounting position on the handlebars.

3.2. Rear Light Installation

The Acid Pro rear light also uses a flexible silicone strap for easy and tool-free attachment to your seat post or other suitable bicycle frame parts.

1. Open the silicone strap on the rear light.
2. Place the light on your bicycle's seat post, ensuring it faces directly backward.
3. Wrap the silicone strap around the seat post and secure it to the hook on the light. Ensure it is tight and stable.

Image: Close-up of the Acid Pro rear light, highlighting its red lens and reflector design.

4. Käyttö

4.1. Valojen lataaminen

Both the front and rear lights are rechargeable via the included micro USB cable. It is recommended to fully charge the lights before first use.

• Locate the micro USB port on each light. For the rear light, it is typically on the side or bottom, protected by a rubber flap.
• Connect the micro USB cable to the light's port and the other end to a USB power source (e.g., computer USB port, USB wall adapter).
• An indicator light (usually red during charging, green when fully charged) will show the charging status.
• Latausaika voi vaihdella, mutta täyteen lataaminen kestää yleensä muutaman tunnin.

Image: Close-up of the Acid Pro rear light, showing the micro USB charging port with its protective cover.

4.2. Kytkeminen päälle/pois

Each light has a power button, usually located on the top or side.

• Valon kytkemiseksi päälle ON, press and hold the power button for approximately 1-2 seconds.
• Valon kytkemiseksi päälle POIS, press and hold the power button again for approximately 1-2 seconds.
• Some models may have multiple light modes (e.g., steady, flashing). Briefly press the power button to cycle through available modes.

5. Huolto

Proper maintenance will extend the lifespan of your lighting set:

• Puhdistus: Pyyhi valot pehmeällä, d:lläamp liinaa. Älä käytä hankaavia puhdistusaineita tai liuottimia, sillä ne voivat vahingoittaa laitetta.asing tai objektiivi.
• Akun hoito: Recharge the batteries regularly, even if the lights are not used frequently, to maintain battery health. Avoid completely draining the battery before recharging.
• Varastointi: Store the lights in a cool, dry place when not in use. If storing for an extended period, ensure the batteries are partially charged (around 50%) to prevent deep discharge.
• Vedenkestävyys: While splash-proof (IP44 rated), avoid submerging the lights in water. Ensure the USB port cover is securely closed to maintain water resistance.

6. Vianmääritys

If you encounter issues with your lighting set, try the following:

• Valo ei syty: Ensure the battery is charged. Connect the light to a USB power source and check the charging indicator.
• Valo on himmeä: Akun varaus saattaa olla vähissä. Lataa valo täyteen.
• Valo välkkyy: Check the mounting to ensure it is secure. If the issue persists, recharge the battery.
• Latausongelma: Try a different micro USB cable or USB power source. Ensure the cable is fully inserted into the port.

If these steps do not resolve the issue, please contact Cube customer support or your retailer for further assistance.

7. Tekniset tiedot

8. Takuu ja tuki

For warranty information and customer support, please refer to the documentation provided with your purchase or visit the official Cube websivusto. Säilytä ostokuittisi mahdollisten takuuvaatimusten varalta.