1. Tuote ohiview
This HURI replacement kit provides essential components for the fuel system of various outdoor power tools. It includes primer bulbs and fuel line tubing designed to restore proper fuel delivery and engine starting functionality.
1.1 Pakkauksen sisältö
- 5 x pohjustelamppua
- 2 feet x Fuel Line
1.2 Yhteensopivat mallit
This kit is compatible with a range of Stihl and McCulloch models, including but not limited to:
- Stihl: MS211, MS211C, MS192T, MS192TC, MS210, MS230, MS250, HT250, FS36, FS40, FS44, FS120, FS120R, FS250, FS250R
- McCulloch: Eager Beaver 282, 287, 28, 297, 327bc, 32bcs, 285, 282 Silver Eagle 28, 32, 2818, 4600, 5000, 3020, 4700, 2012, 3200, 3210, 3214, 3216, 3200, 3205, 3336, Mac 17, 19, 22, 2816, 328, 28, 282, 3227, 327b, 32bc, 2817
2. Turvallisuustiedot
Always prioritize safety when working with fuel systems and power tools. Failure to follow safety precautions can result in injury or damage.
- Ensure the engine is pois ja viileä before beginning any work.
- Irrota sytytystulpan johto tahattoman käynnistymisen estämiseksi.
- Työskentele hyvin ilmastoidussa tilassa välttääksesi polttoainehöyryjen hengittämistä.
- Käytä asianmukaisia henkilönsuojaimia, kuten käsineitä ja silmäsuojaimia.
- Pidä sammutin helposti saatavilla.
- Hävitä vanha polttoaine ja osat vastuullisesti paikallisten määräysten mukaisesti.
3. Tarvittavat työkalut
Asennukseen saatetaan tarvita seuraavia työkaluja:
- Pihdit
- Pieni litteäpäinen ruuvimeisseli
- Utility knife or sharp scissors (for fuel line trimming)
- Hair dryer or heat gun (optional, for softening fuel lines)
- Puhtaat rievut
4. Asennusohjeet
Follow these steps to replace the primer bulb and fuel lines. Specific procedures may vary slightly depending on your tool model.
4.1 Replacing the Primer Bulb
- Paikanna imukuppi: Identify the existing primer bulb on your carburetor or engine housing.
- Irrota polttoaineletkut: Carefully pull off the fuel lines connected to the old primer bulb. Note which line connects to which nipple (typically one shorter, one longer). If lines are stiff, a hair dryer can be used to gently warm them for easier removal.
- Poista vanha polttimo: The primer bulb is usually held in place by two clasps. Gently pry these clasps to release the old bulb.
- Asenna uusi lamppu: Insert the new HURI primer bulb into the opening, ensuring the clasps snap securely into place.
- Polttoaineletkujen kytkeminen uudelleen: Attach the fuel lines to the corresponding nipples on the new primer bulb. The shorter nipple typically connects to the fuel tank, and the longer nipple connects to the carburetor. If the fuel lines are difficult to attach, gently warm them with a hair dryer to make them more pliable.
4.2 Replacing Fuel Lines
If your existing fuel lines are cracked, brittle, or leaking, they should also be replaced.
- Identify Lines: Trace the fuel lines from the primer bulb/carburetor to the fuel tank. Note their routing and connections.
- Remove Old Lines: Carefully disconnect the old fuel lines from all connection points (primer bulb, carburetor, fuel filter in tank).
- Cut New Lines: Using the old lines as a guide, cut the new HURI fuel line tubing to the appropriate lengths. Ensure clean, straight cuts.
- Install New Lines: Route the new fuel lines in the same manner as the old ones. Connect them securely to the primer bulb, carburetor, and fuel filter. Ensure all connections are snug to prevent leaks.
Image 1: HURI Primer Bulb and Fuel Line Kit. This image displays multiple clear primer bulbs with black bases and a coiled length of yellow translucent fuel line tubing, illustrating the components included in the replacement kit.
5. Operating Instructions (After Installation)
After replacing the primer bulb and fuel lines, it is crucial to prime the fuel system before attempting to start the engine.
- Polttoainesäiliön täyttö: Ensure the fuel tank contains fresh, appropriate fuel for your power tool.
- Järjestelmän pohjustus: Press the primer bulb repeatedly (typically 5-10 times) until you see fuel flowing into the bulb and returning to the fuel tank. The bulb should feel firm.
- Käynnistä moottori: Follow your power tool's specific starting procedure.
6. Huolto
Regular inspection and maintenance can extend the life of your fuel system components.
- Tarkista säännöllisesti: Periodically check the primer bulb and fuel lines for cracks, hardening, or signs of leakage.
- Puhdas: Keep the area around the primer bulb and fuel lines free of dirt and debris.
- Oikea polttoaine: Always use the correct fuel mixture (if applicable) and fresh fuel to prevent damage to fuel system components.
- Varastointi: When storing your tool for extended periods, drain the fuel system or use a fuel stabilizer to prevent fuel degradation.
7. Vianmääritys
Jos asennuksen jälkeen ilmenee ongelmia, harkitse seuraavia yleisiä ongelmia ja ratkaisuja:
| Ongelma | Mahdollinen syy | Ratkaisu |
|---|---|---|
| Engine won't start / No fuel in primer bulb | Clogged fuel filter, kinked fuel line, incorrect fuel line connection, air leak. | Check fuel filter for clogs and replace if necessary. Ensure fuel lines are not kinked and are connected correctly. Verify all connections are tight. |
| Fuel leak around primer bulb or lines | Loose connections, damaged primer bulb, cracked fuel line. | Tighten all fuel line connections. Inspect primer bulb for cracks; replace if damaged. Inspect fuel lines for cracks; replace if damaged. |
| Primer bulb does not return to original shape | Damaged primer bulb. | Vaihda imukuppi. |
8. Tekniset tiedot
| Ominaisuus | Yksityiskohta |
|---|---|
| Merkki | HURI |
| Materiaali | Muovi |
| Primer Bulb Height | 31.4 mm (1.236 tuumaa) |
| Primer Bulb Width | 21.4 mm (0.842 tuumaa) |
| Fuel Line Length | 2 jalkaa |
| Tuotteen paino | 40 grammaa |
9. Takuu ja tuki
HURI provides a manufacturer warranty for this product.
- Takuuaika: 2 kuukautta ostopäivästä.
- Tukea: For warranty claims or technical assistance, please contact the seller, HURIPARTS, through the platform where the purchase was made.