Hansgrohe Ecostat S Thermostatic Mixer User Manual

Tuote loppuview

The Hansgrohe Ecostat S Thermostatic Mixer is a wall-mounted unit designed for precise temperature control in your bathroom. It features a safety stop at 40°C to prevent scalding and ensures a consistent water temperature. This mixer is engineered for durability and user-friendliness, reflecting Hansgrohe's commitment to quality and innovation in bathroom fixtures.

Kuva 1: Etuosa view of the Hansgrohe Ecostat S Thermostatic Mixer.

Mukana olevat komponentit

The following components are typically included with your Hansgrohe Ecostat S Thermostatic Mixer:

• Termostaattiyksikkö
• Kokoamisohje
• Sekoitusyksikkö
• Asennusmateriaali

Please note that a separate BASIC set and shut-off valve are not included and may be required for complete installation.

Asennus ja asennus

The Hansgrohe Ecostat S Thermostatic Mixer is designed for wall-mount installation. Professional installation is recommended to ensure proper function and compliance with local plumbing codes.

Asennusta edeltävät tarkastukset:

• Varmista, että vedensyöttö on katkaistu ennen asennuksen aloittamista.
• Varmista, että kaikki mukana tulevat osat ovat mukana.
• Confirm that the operating pressure in your system is within the recommended range of min 1 bar to max 10 bar.

Asennusohjeet:

Refer to the detailed assembly instructions provided with the product for specific mounting steps. The mixer requires a wall-mount setup. Ensure adequate space and proper pipe connections for hot and cold water lines.

Figure 2: Dimensional drawing of the Hansgrohe Ecostat S Thermostatic Mixer. All measurements are in millimeters.

Käyttöohjeet

The Ecostat S Thermostatic Mixer provides precise control over water temperature.

Lämpötilan säätö:

• Rotate the temperature handle to adjust the water temperature.
• The integrated safety stop is set at 40 °C (104 °F) to prevent accidental scalding. To exceed this temperature, you must consciously override the safety stop by pressing a button or turning the handle past the stop point (refer to the specific product diagram for your model).

Virtausnopeus:

The flow rate of the mixer is dependent on the water pressure. This model is designed for a flow rate of up to 37 liters per minute (l/min) at 3 bar paine.

Figure 3: Flow rate diagram illustrating the relationship between pressure (MPa/bar) and flow (l/min) for the thermostatic mixer.

Huolto ja hoito

To ensure the longevity and optimal performance of your Hansgrohe Ecostat S Thermostatic Mixer, follow these maintenance guidelines:

• Puhdistus: Clean the chrome and silver surfaces regularly with a soft cloth and mild soap or a non-abrasive cleaner specifically designed for bathroom fixtures. Avoid harsh chemicals, abrasive pads, or cleaners containing alcohol, ammonia, or bleach, as these can damage the finish.
• Lämpötilan kalibrointi: If the water temperature is not consistent with the dial setting, the thermostatic cartridge may need recalibration. Refer to the detailed assembly instructions for steps on how to recalibrate the thermostat.
• Suodattimen huolto: Periodically check and clean any integrated filters to prevent debris buildup, which can affect flow rate and temperature stability.

Vianetsintä

Tässä osiossa käsitellään yleisiä ongelmia, joita saatat kohdata termostaattisen sekoittimen kanssa.

If the issue persists after attempting these solutions, it is recommended to contact a qualified plumber or Hansgrohe customer support for further assistance.

Tekniset tiedot

Takuu ja tuki

Specific warranty details for the Hansgrohe Ecostat S Thermostatic Mixer are typically provided with the product packaging or can be found on the official Hansgrohe websivusto. On suositeltavaa säilyttää ostokuitti takuuvaatimuksia varten.

For technical support, spare parts, or service inquiries, please visit the official Hansgrohe website or contact their customer service department. Contact information can usually be found in the product documentation or on the manufacturer's websivusto.