Fevos FL01 Flya Way Lamp
Product Usage Instructions:
Charging Instructions:
We recommend fully charging the battery before first use. The initial full charge via USB C takes about 3 hours.
LED Indicator Information (Charging):
- Charge using a USB C cable.
- LED Light Status:
- Red: Charging in progress
- Blinking Red: Low battery
- Green: Fully charged
Operating Instructions:
Setting Up the Sleep Light Speaker:
The light function can be controlled by the top touch button.
- To turn the light on, click the top touch button.
- To switch light colors or lighting modes:
- Single Click: Switch between 9 colors.
- Double Click: Switch between cold white + warm white and RGB modes.
- To switch breathing light mode, tap the top button three times.
- To adjust brightness, long-press the top touch button to reach the desired level and release it.
- To turn off the light, wait 3 seconds and click the top touch button.
Box contents One DreamWave
- USB Type C charging cable
- This user manual
Product Overview
- Touch area (lighting function)
- 360° rotating light
- White noise button
- Switch button
- Volume button
- Timing button
- Setting button
- LED indicator (Bluetooth and charging)
- USB Type C charging port
Feature
- Built-in eight kinds of white noise
- 360° rotating LED light design
- Memory system dimmable LED light
- LED indicator is available in 9 colors (warm white, cold white, blue, yellow, green, red, purple, light pink and light blue)
- Two machines can be TWS paired to synchronize LED lights and white noise
- for outdoor use (IPX4)
- USB Type-C charging
Charging
- We recommend that you fully charge the battery before using it for the first time The first full charge via USB C takes about 3 hours.
LED indicator information (Charaina)
| Charge using a USB C cable | LED Light Status (Red) |
| charge | The LED indicator continues to light up |
| in use | LED indicator light off |
| low battery | The LED indicator blinks red |
| Fully charged | The LED indicator is green |
Charging with a USB C cable
- Connect the attached USB C-type cable to the charging port.
- Plug the USB port of the cable into any USB charger.
operating instructions
Set up a sleep light speaker
| The function of the light is controlled by the top touch button | |
| turn the light on | Click the top touch button |
| Switch light colors | Click the top touch button to switch between the 9 colors |
| Switch lighting mode | Double click the top touch button to switch between cold white + warm white and RGB lighting modes |
| Switch breathing light mode | Three touch the top button to switch the breathing light mode |
| adjust brightness | Long press the top touch button to reach the desired brightness and release it |
| douse the glim | Wait 3 seconds and click the top touch button |
| The next time you use it, the light will use the light color and light effect set last time. | |
| Startup & Shutdown | Tap and hold  key |
| volume adjustment | Short press key Turn up the volume Short press key volume down |
| White noise play | Short press  key Play corresponding white noise (Each key can control 2 pieces) |
| Turn off white noise | Tap and hold key Turn off corresponding white noise |
| timing | Short press  key Turn on and off the corresponding timing period (minutes) |
| mode setting command | Short press key Switch Bluetooth/Music mode |
Two sleep light speakers synchronized (TWS Interconnect)
- Short press key Switch to Bluetooth mode and the LED indicator flashes blue
- Double click Enable Bluetooth TWS pairing. After the pairing is successful, the host is steady blue and the secondary blinks blue.
- Double click Cancel the Bluetooth TWS pairing, the LED indicator flashes blue after the cancellation is successful When the two TWS are interconnected, light effects, white noise playback, and timing can be synchronized
LED indicator information (Bluetooth)
| operator schema | LED Light Status (blue) |
| Bluetooth mode | Fast blinking indicator light |
| Bluetooth connection successful | The main indicator is steady on, and the secondary indicator is blinking |
safety precautions
- IPX4 waterproof, rainproof, splashproof proof and sprayproof.
- Do not put the device into water to avoid internal short circuit, overheating, fire, deformation, or even internal battery explosion.
- do not store the equipment in extremely hot or cold areas.
Recommended for use at room temperature. - Do not attempt to repair, repair or modify the device by yourself.
- Ensure that you comply with the technical specifications for charging and do not use a power adapter whose output voltage exceeds the specified value to avoid any irreversible damage to the internal circuit (DC input voltage: 5V).
product standard
- Material: Plastic (Plastic)
- Weight :190 g/0.42 lbs
- Size: 121.5*89.8*79.6mm
- Max lumen output:50 Im Temperature:
- Warm white: 3000K
- Cold White: 5800K
Battery voltage: 3.7V - Operating temperature: 0℃-45℃
- Bluetooth®(Bluetooth) connection range: 8m
- Frequency range: 2402 MHz- 2480 MHz
Input interface: USB C - Battery type: Lithium polymer
- Battery capacity: 1200 mAh
- Charging system: USB Type C interface
- Charging time (USBC type) : about 3 hours
- Normal battery life: up to 8h* (brightness 75%)
- International Protection: 1 year
Varies according to use, set light intensity, and selected light color
FCC warning
This device complies with Part 15 of the FCC Rules.
Operation meets the following two conditions :
- This equipment does not produce harmful interference, and
- This equipment must accept any interference received, including interference that may cause unintended operation.
Any change or modification without the express approval of the responsible party for compliance may give the user no right to operate the equipment.
Note: This device has been tested to comply with the restrictions on Class B digital devices in Part 15 of the FCC Rules. These restrictions are intended to provide reasonable protection against harmful disturbances in residential installations.The device produces uses and can radiate RF energy, which, if not installed and used according to instructions, may cause harmful interference with radio communications. However, there is no guarantee that interference will not occur in a particular installation.If this device does cause harmful interference with radio or television reception (which can be determined by turning off and lifting the device), users are advised to try to correct the interference by one or more of the following measures:
- Readjust or place the receiving antenna.
- Increase the distance between the device and the receiver.
- Connect the device to a circuit socket different from the circuit connected to the receiver.
- Consult a dealer or an experienced radio/TV technician for help
The device has been evaluated to meet the general RF exposure requirements. The device can be used in portable exposure conditions without restriction
FAQS
Q: What do the different LED light colors indicate?
A: The LED indicator shows different colors to indicate charging status – Red for charging, Blinking Red for low battery, and Green for fully charged.
Q: How do I know when the Bluetooth connection is successful?
A: In Bluetooth mode, a fast blinking blue indicator light signifies a successful connection.
Documents / Resources
 |
Fevos FL01 Flya Way Lamp [pdf] Instruction Manual FL01 Flya Way Lamp, FL01, Flya Way Lamp, Way Lamp, Lamp |