EVENT LIGHTING APRO4-IP DMX Controller

For your safety, please read this user manual carefully before use.
Event Lighting reserves the right to revise the manual at any time. Information and specifications within this manual are subject to change without notice. Event Lighting assumes no liability or responsibility for any errors or omissions. Please consult Event Lighting for any clarification or information regarding this item.

FEATURES

• DMX 512, RDM, Artnet and sACN support
• Remote configuration via internal webpage
• Update firmware on Webpage
• DMX output isolation
• RJ45 Ethernet B input with POE（DC12V 2A）
• LCD Display
• Gigabit network, 100/1000mbps port speed
• IP65 Rating

PANEL OVERVIEW

1. Ethernet port RJ45
2. Ethernet port RJ45
3. Power in/out True1
4. 2xDMX5pin connectors
5. 2xDMX5pin connectors
6. Fuse holder
7. LCD Display protection cover

MENUS
Below is controller Menus map

MainMenu	Sub Menu 1	Sub Menu 2	Value/Option	Default
Network	IP Mode		DHCP	Static
			Static
	IP Address		2.xx.xx.xx	2.xx.xx.xx
	Subnet Mask		255.0.0.0	255.0.0.0
DMX Port	Protocol	Artnet		Artnet
		sACN
	Start Net		000‐127	000
	Start Universe		000‐255	000
	Port 1	Mode	Off	On
			On
		NET	000‐127	000
		Universe	000‐255	000
	Port 2	Mode	Off	On
			On
		NET	000‐127	000
		Universe	000‐255	001
	Port 3	Mode	Off	On
			On
		NET	000‐127	000
		Universe	000‐255	002
	Port 4	Mode	Off	On
			On
		NET	000‐128	000
		Universe	000‐255	003
			Disable
Settings	DMX Rate		20Hz	30Hz
			25Hz
			30Hz
			35Hz
			40Hz
	RDM	Disable		Disable
		Enable
	Display On	Always		1Min
		30Sec
		1Min
		5Min
	Signal Loss	Hold DMX		Hold DMX
		Stop Output
	Merge Mode	HTP		HTP
		LTP
	Factory Reset	No		No
		Yes

WEB configuration

NET device network IP mode can set to DHCP mode or Static mode.

DHCP mode

• When APRO4‐IP is set to DHCP mode, you need to set the computer to DHCP also. And use a router for linking computer and APRO4‐IP device. The controller will show IP address like below:
• Enter IP address in your web browser, then you can login webpage to configure the parameter of controller.

Enter password: admin

Static mode

• When APRO4‐IP device is set to Static mode, you need to set computer to be Static mode also. APRO4‐IP device will show IP address as below:
• Then set the IP address of computer is in the same IP range manually. For example: IP address must start with 2 according to APRO4‐IP address. And netmask is same with 255.0.0.0.
• Input static IP address of APRO4‐IP device in your browser, then you can login to configure the parameter of device.

Enter password: admin

• When log on NET Config web, the first page show the information about APRO4‐IP.
• Following  is  for  Network  setting,  you  can  set  IP  mode  to  be  Static  or  DHCP,  IP  Address,and Subnet Mask. After setting, click Save button .
• For DMX Port page , it is used for DMX Port setting. You can select Protocol to be Artnet or sACN, and set each port as input or output.
• On the page of Setting , you can set DMX Rate, RDM , Display On and Signal Loss. After setting, click Save to store the setting.
• DMX  Rate:  You  can  set  20Hz,  25Hz,  30Hz,  35Hz,  40Hz,  30Hz  is default setting.
• RDM: You can set RDM to be Disable or Enable.
• There is 4 options for Display On mode: Always, 30Sec, 1Min, 5Min.
• Signal Loss: Can set as Hold DMX or Stop Output.
• You can return to factory setting by click Factory Reset button.
• On Update page, you can update software of fixture by selecting the update software file of APRO4‐IP.
• On the last page, you can reset password.

SPECIFICATION

• Power in: AC 100‐240V,50/60Hz
• Power consumption: AC240V 50HZ 0.05A
• Size: 215.3×150.5x42mm 4.2W
• Weight: 1.43Kg
• POE 802.3af
• IP65

DIMENSIONS

Warranty

Please refer to your local dealer or contact Event Lighting. www.event‐lighting.com.au

Frequently Asked Questions

How do I reset the APRO4-IP device to factory settings?

To perform a factory reset on the APRO4-IP device, access the Factory Reset option in the Main Menu under Settings. Confirm the reset to restore the device to its default configuration.

What is the default IP address for the APRO4-IP device?

The default IP address for the APRO4-IP device is set to DHCP mode. If you switch to Static mode, you can set a specific IP address within the range provided in the user manual.

Documents / Resources

EVENT LIGHTING APRO4-IP DMX Controller [pdf] User Manual APRO4-IP, APRO4-IP DMX Controller, DMX Controller, Controller

References

• User Manual