EseeCloud JTY1 Low Power Battery Camera
Product Information
- Product: Low Power Battery Camera
- Compliance: Part 15 of FCC rules
- Conditions: Must not cause harmful interference and must accept any received interference
Product Usage Instructions
Installation
- Insert the batteries into the camera.
- Position the camera in the desired location for monitoring.
- Ensure the camera is securely mounted or placed to avoid movement.
Operation
- Turn on the camera using the designated power button.
- Adjust the camera settings as needed for your monitoring requirements.
- Monitor the camera feed either through a connected device or a designated monitor.
Setup and installation
Boot up
When remote view by connecting to the router and direct connection method, please boot the device after insertting the SD card. When using by pairing to the wireless NVR, please make sure the memory(SD card, HDD etc.) of the wireless NVR is ready.
App Installation
APP Download and Installation
- Use your mobile phone to scan the below QR code to download and install “EseeCloud”, and follow the APP prompts to complete user registration.
- Note: For iOS system, it requires iOS 9.0 version or above.
- For Android, Android 5.1 or above.
Adding method 1: Scanning directly the QR code on the camera when the battery camera is used by connecting the network and local direct way.
- Put both of your mobile phone and camera near the router,and the distance should be 30-100cm.
- After the battery camera is powered on,there is a voice prompt “start match code” and the red LED light flashes. (Otherwise please press the RESET button on the camera for 8 seconds, it will be available after the voice prompt “reset successfully”).
Add Camera to Mobile App
Method 1 – By WIFI Connection
Please full charge camera for 12 hours at the first time use.
- Turn on the camera
- Click “Add camera” on your mobile app.
- Please turn on wireless connect to WIFI–Enable
- Waiting for configuring successfully (100%) ,then you can name your camera.
- The connection is successful and you can use your camera.
Troubleshooting
FAQ
Why does the battery run out quickly?
The App will count the daily recording time when playback video. Please check if there are more videos every day. If there are many false triggers, please try to lower the trigger sensitivity setting. Check if the WiFi signal between the camera and the wireless NVR or router is weak. You can try to change the WiFi channel of the wireless NVR or router; or adjust the position of the wireless NVR, router or camera to improve the signal transmission.
How to confirm that the network connection between the camera and the router or wireless NVR is normal?
A: Actively trigger PIR in front of the camera and wait for about 10s. If the camera flashes red, it means that the camera cannot connect to the router or wireless NVR smoothly. If it is connected to a wireless NVR, you can click play from the corresponding channel of the NVR touch screen. If the video can be played, the connection is normal Whether the indicator of the corresponding channel on the base station is always on. The blinking of the indicator indicates that the base station and the battery camera have been disconnected.
When do wiless NVR NVR touchable monitor basree station and battery camera need to be paired?
Matching code is to make the camera wif connect to the wireless NVR automatically. The devices purchased in the entire package is already matched code in the factory, and no match code operation is required. You need to match code when a new battery camera need to be added to the wireless NVR; The battery camera needs to be code matched after being reset to factory settings; The wireless NVR needs to be code matched after being restored to the factory settings; After deleting the paired cameras on the wireless NVR channel through the App, you need to match code again.
Q: What should I do if the camera stops working suddenly?
Check the battery levels and replace them if needed. Ensure there is no physical damage to the camera.
FCC STATEMENT
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions,may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
FCC NOTICE
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference; and
- this device must accept any interference received, including interference that may cause undesired operation.
FCC CAUTION
Caution the user that changes or modifications not expressly approved by the party responsiblefor compliance could void the user’s authority to operate the equipment.）
Please read the Quick Start Guide carefully before using the product and keep it properly.
Documents / Resources
 |
EseeCloud JTY1 Low Power Battery Camera [pdf] User Guide 2BMU3-JTY1, 2BMU3JTY1, JTY1 Low Power Battery Camera, JTY1, Low Power Battery Camera, Battery Camera, Camera |
