Apuro Blender Instruction Manual

Safety Instructions

Telephone Helpline: 1300225960 (AU) / 0800 222 700 (NZ)

• Position on a flat, stable surface.
• A service agent/qualified technician should carry out installation and any repairs if required. Do not remove any components on this product.
• Consult Local and National Standards to comply with the following:
  • Health and Safety at Work Legislation
  • Fire Precautions
  • Wiring Regulations
  • Building Regulations
• DO NOT use jet/pressure washers to clean the appliance.
• DO NOT immerse the appliance in water.
• This appliance is only used for blending food. Do not use the appliance for anything other than its intended use.
• Always switch off and disconnect the power supply to the appliance when not in use.
• Not suitable for outdoor use.
• Keep all packaging away from children. Dispose of the packaging in accordance to the regulations of local authorities.
• If the power cord is damaged, it must be replaced by an Apuro agent or a recommended qualified technician in order to avoid a hazard.
• This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning the use of the appliance by a person responsible for their safety.
• Children should be supervised to ensure that they do not play with the appliance.

Introduction

Please take a few moments to carefully read through this manual. Correct maintenance and operation of this machine will provide the best possible performance from your Apuro product.

Product Description

• CY140-A - Apuro Blender with Touch Control - 2.5Ltr Jug
• CY141-A - Apuro Blender with Touch Control - 2.5Ltr Jug - with Sound Enclosure

Pack Contents

• Apuro Blender
• Blender Jug, lid and lid plug
• Food pusher
• Instruction manual

Apuro prides itself on quality and service, ensuring that at the time of unpacking the contents are supplied fully functional and free of damage.

Should you find any damage as a result of transit, please contact your Apuro dealer immediately.

Operation

Model: CY140-A

Model: CY141-A

Diagram Description: The document shows two blender models. The CY140-A is a jug blender with a base unit containing controls. The CY141-A is similar but includes a 'Sound Enclosure' covering the jug. Key components labeled include: Lid plug, Lid, Jug, Sound Enclosure (for CY141-A), Food pusher. The base unit features a digital display and control buttons labeled: On/Off key [Power Button], Pulse key (P) [Pulse Button], Time selection keys [Timer Buttons], Speed selection keys [Speed Buttons].

Before Use:

• Disconnect the blender from power supply.
• Clean all removable parts thoroughly.

Blending Steps:

1. Plug in Blender.
2. Place ingredients into jug.
3. Secure the lid and lid plug (Note: Always operate with the lid secured).
4. Locate jug on to body of blender. The On/Off key [Power Button] lights up.
5. Press the On/Off key [Power Button] to enter standby. Press again to start blending with the default speed setting (2).
6. Pulse function: Press and hold the Pulse key [Pulse Button] to start. Release to stop.
7. After use, press the On/Off key [Power Button] to switch off blender.

Using the Timer Function

To use the timer function during blending:

1. Press the desired time key [Timer Button]. Then press the speed key [Speed Button] or On/Off key [Power Button].
2. The blender starts while the timer counts down on the display.
3. When the set time expires, the blender switches off automatically.

During use, you can press the time/speed key [Timer/Speed Button] to pause operation. Press again to continue.

Cleaning, Care & Maintenance

• Always disconnect from power supply before cleaning.
• Always allow to cool before cleaning.
• Let the motor come to a complete stop before removing the jug.
• The jug is NOT dishwasher proof!
• Do not leave jug to soak.
• Use warm, soapy water and a damp cloth to clean the jug.
• Dry thoroughly after cleaning.

⚠️ Warning: Blade is sharp - handle with care.

⚠️ Warning: Do not allow any water to spill into the body of the appliance when cleaning.

Troubleshooting

A qualified technician must carry out repairs if required.

Technical Specifications

Note: Due to our continuous improvement process, the product specifications are subject to change without notice.

Electrical Wiring

The plug is to be connected to a suitable mains socket.

This appliance is wired as follows:

• Live wire (coloured brown) to terminal marked L
• Neutral wire (coloured blue) to terminal marked N
• Earth wire (coloured green/yellow) to terminal marked E

This appliance must be earthed. ⏚ [Earth Symbol]

If in doubt consult a qualified electrician.

Electrical isolation points must be kept clear of any obstructions. In the event of any emergency disconnection being required they must be readily accessible.

Compliance

The product must not be disposed of as household waste. To help prevent possible harm to human health and/or the environment, the product must be disposed of in an approved and environmentally safe recycling process. For further information on how to dispose of this product correctly, contact the product supplier, or the local authority responsible for waste disposal in your area.

Apuro parts have undergone strict product testing in order to comply with regulatory standards and specifications set by international, independent, and federal authorities.

Apuro products have been approved to carry the following symbol: ✅ [Compliance Symbol]

Declaration of Conformity

This section declares that the specified equipment conforms to relevant Territory Legislation, Directives, and Standards.

Manufacturer: Apuro

Equipment Types Declared:

• Blender with touch control - 2.5Ltr Jug
• Blender with touch control - 2.5Ltr Jug - with Sound Enclosure
• Blender - 2.5Ltr Jug
• Blender - 2.5Ltr Jug - with Sound Enclosure

Applicable Legislation & Directives:

• Electrical Safety: EN 60204-1:2018, EN 12852:2001+A1:2010, EN ISO 12100:2010
• Electro-Magnetic Compatibility (EMC): EN IEC 55014-1:2021, EN IEC 55014-2:2021, EN IEC 61000-3-2:2019+A1:2021, EN 61000-3-3:2013+A1:2019+A2:2021

Declaration Details:

Date: 15th Oct 2024

Signed by:

• Ashley Hooper, Group Head of Product Quality & Compliance (Address: Fourth Way, Avonmouth, Bristol, BS11 8TB, United Kingdom)
• Brendan Denmeade, Commercial Manager/ Responsible Supplier (Address: 15 Badgally Road, Campbelltown NSW 2560)