Tchibo Shoe Bench with Seat and Pull-Out Step
Assembly Instructions
Important Information
Please read these instructions carefully before assembly and keep them for future reference. If you pass on the item, also hand over these assembly instructions.
Safety Precautions:
- Danger to children: Keep packaging material away from children. Bags and films are not toys. Ensure children do not pull them over their heads or swallow parts. Risk of suffocation!
- The product contains small parts that can be life-threatening if swallowed. Keep children away during assembly.
- Keep infants away from the product as they may try to pull themselves up on it or climb onto it.
- Caution - Risk of injury and material damage:
- Always place the product on a level, non-sloping surface.
- Never stand on the product; it could fall over or be damaged.
- Do not place the product freely in a room or against a wall without fastening. For optimal stability, it must be fastened to a suitable wall.
- Mounting material (screws and wallplugs) is provided for wall mounting. This material is suitable for standard, solid masonry. Before mounting, ascertain the correct mounting material for your wall and ensure there are no pipes or electrical wiring behind the drilling location.
- Assemble the product on a soft and even surface, using the transport cardboard underneath to avoid scratching or damaging surfaces.
- Regularly check all screw connections and retighten if necessary.
- Use the product only for its intended purpose and do not overload it.
Intended Use
This product is suitable for indoor use. Protect it from moisture. It is designed for home use and is not suitable for commercial purposes.
Care Instructions
This product is manufactured from oiled eucalyptus wood.
- Do not use abrasive or caustic cleaning agents or hard brushes for cleaning.
- Clean the surfaces with a slightly damp cloth and wipe them off with a dry cloth.
- If used intensively, you can re-oil the wood with a suitable oil. Consult a specialist shop for advice if needed.
- Warning - Risk of fire! Never leave oil-soaked cloths crumpled up to dry, as they may self-ignite. Immediately after use, spread the cloth out and hang it on a clothesline with pegs to dry.
- Wood is a natural product. Fine cracks may appear with continuous periods of hot temperatures and dry conditions. These do not impair the product's quality or function.
Unpacking and Disposal
Carefully remove all packaging material and dispose of it properly. Ensure you do not accidentally discard any assembly materials.
Parts List
The following replacement parts can be ordered:
| Item | Part Number | Item | Part Number | Item | Part Number |
|---|---|---|---|---|---|
| 1 | 5068229 | A | 5068289 | S1 | 5068294 |
| 2 | 5068280 | B | 5068290 | S2 | 5068295 |
| 3 | 5068281 | C | 5068291 | S3 | 5068296 |
| 4 | 5068282 | D | 5068292 | S4 | 5068297 |
| 5 | 5068283 | E | 5068293 | S5 | 5068298 |
| 6 | 5068284 | ||||
| 7 | 5068285 | ||||
| 8 | 5068286 | ||||
| 9 | 5068287 | ||||
| 10 | 5068288 |
Assembly Steps
Step 1: Attach side panels (5) to the back panel (3) using screws (S2). Attach the top support (6) to the side panels (5) using screws (S2).
Step 2: Attach the other side panel (3) to the back panel (3) using screws (S2). Attach the top support (6) to the side panels (3) using screws (S2).
Step 3: Connect the two assembled side sections using the back panel (2). Secure with screws (S2).
Step 4: Attach the top supports (6 and 7) to the assembled side sections using screws (S2).
Step 5: Attach the top panel (1) to the assembled structure using screws (S3). Attach the lower shelf supports (8) and (9) using screws (S3).
Step 6: Attach the leg supports (10) to the lower shelf supports (8 and 9) using screws (S3).
Step 7: Assemble the pull-out step. Insert the step supports (A) through the holes in the side panels of the bench. Use washers (B) and (C) and secure with screws (S1).
Step 8: Place the top slats onto the assembled bench structure.
Step 9: For wall mounting, use screws (S5) and wall anchors (D) as shown. Ensure the wall is suitable for mounting and that there are no pipes or wires behind the drilling location. Drill holes at the indicated positions (8 mm diameter).
Weight Limits
The maximum weight capacity for each part is indicated:
- Top surface: 130 kg
- Lower shelves: 30 kg each
- Pull-out step: 130 kg
Service and Contact Information
For product information, accessories, replacement parts, or service inquiries, please contact Tchibo customer service. Please provide the article number and order number for replacement parts.
Germany: 040 60 02 79 00 | www.tchibo.de/service | www.tchibo.de/contact
Austria: 0800 400 235 | www.tchibo.at/service | www.tchibo.at/contact
Switzerland: 043 88 33 099 | www.tchibo.ch/service | www.tchibo.ch/contact
Article Number: 691 121
