EMOS ZS2313W LED Floodlight Plus PIR Sensor
Product Specifications
| Type | Input Voltage | Max. Power | Life Span | Luminous Flux | Dimensions | Beam angle |
| ZS2313W | 220–240 V AC
50 Hz |
10 W | 25 000 h | 1 000 lm | 85 × 141 × 52 mm | 120° |
| ZS2323W | 20 W | 25 000 h | 2 000 lm | 114 × 156 × 52 mm | 120° | |
| ZS2333W | 30 W | 25 000 h | 3 000 lm | 143 × 175 × 52 mm | 120° |
Product Usage Instructions
Postion of Light
LED Floodlight is designed for indoor and outdoor use to be mounted on a firm ground. Ingress Protection: IP44 – for outdoor use
PIR sensor – specification
Time-delay: min.. 10 s ±5 s – max. 7 min ±1 min
Detection angle: 120°
Ambient light: 10 lux –> 2 000 lux (adjustable)
Detection distance: max. 8 m
Detection motion speed: 0.6–1.5 m/s
PIR sensor setting: Detection field is possible to be set by moving the motion sensor switch to the left and to the right.
Detection range
The distance at which the sensor responds to movement can be set using the control A – SENS (see picture no.. 4).
Time-delay
You can set the time-delay of the lamp by a button B – TIME (see picture no. 4).
Adjustment of the ambient light (sensitivity)
You can choose at what luminosity will the sensor go on by a button C – LUX (see picture no. 4).
Mounting
Mount the floodlight firmly onto a solid basis, for example, a wall (fig. 1, 2, 3).
Installation height 1.8–2.5 m.
Connect a power cable for connection to a 220–240 V~ power network.
The cable must not be plugged into the power network during the installation of the spotlight.
Direct the floodlight as shown in fig. 1 and 2.
L – brown – live wire
G – green & yellow – earth wire (ground)
N – blue – neutral wire
Maintenance instructions:
- Before maintenance, switch off the floodlight and wait until it has cooled.
- Clean it with a soft, moistened cloth.
- Never submerge the floodlight in water or other liquids. During maintenance, observe general rules for occupational safety and be very careful.
WARNING
- The floodlight is designed entirely for firm mounting.
- Before connecting to the 220–240 V~, make sure that the connecting wire is not under voltage. This operation can be carried out only by an authorized person.
- Respect a minimum distance of 1 m between the appli-ance and the object or surface that you wish to lighten.
- If you place the Floodlight below the roof, keep a minimum of 0.2 m measured from the upside of the Floodlight to the bottom of the roof.
- Do not use the Floodlight without the protection glass.
- The protection from dangerous contact voltage is ensured by „earthing“.
- The external flexible cable or cord of this luminaire cannot be replaced; if the cord is damaged, the luminaire shall be destroyed.
- The lights source of this luminaire is not replaceable; when the light source reaches its end of life the whole luminaire shall be replaced.
- The terminal block is not included. Installation may require advice from a qualified person.
- Terminal block for connection of power supply: 3 termi-nals screw-less type, rated for cross-section range in-cluding 1 mm2 and voltage min 230 V. Type Z attachment.
- Caution: risk of electric shock.
Declaration of Conformity
EMOS spol. s r.o. declares that the ZS2313W, ZS2323W, ZS2333W is in compliance with the essential requirements and other relevant provisions of Directive. The device can be freely operated in the EU. The Declaration of Conformity can be found at http://www.emos.eu/download.
www.emos.eu
FAQs
- Q: How should I clean the floodlight?
Clean the floodlight with a soft, moistened cloth. Do not submerge it in water or other liquids. - Q: What is the lifespan of the product?
The lifespan of the ZS2313W, ZS2323W, and ZS2333W is 25,000 hours. - Q: Can the floodlight be used in the EU?
- Yes, the floodlight can be freely operated in the EU as it complies with essential requirements and relevant provisions.
Documents / Resources
 |
EMOS ZS2313W LED Floodlight Plus PIR Sensor [pdf] Instruction Manual ZS2313W, ZS2323W, ZS2333W, ZS2313W LED Floodlight Plus PIR Sensor, ZS2313W, LED Floodlight Plus PIR Sensor, Floodlight Plus PIR Sensor, PIR Sensor |