ECS Electronics logoECS Electronics SZ-019-DL Towbar Wiring Kits

SZ-019-DL Towbar Wiring Kits

ECS Electronics SZ-019-DL Towbar Wiring Kits - figure 1Fitting instructions electric wiring kit tow bar with 13-P socket up to DIN/ISO Norm 11446.
– We would expressly point out that assembly not carried out properly by a competent installer will result in cancellation of any right to damage compensation, in particular those arising by virtue of the product liability act.
– Contents of these kits and their fitting manuals are subject to alteration without notice, please ensure that these instructions are read and fully understood before commencing installation.
– Do not overload circuits; the maximum loads per connection are detailed in this manual.

Part List

ECS Electronics SZ-019-DL Towbar Wiring Kits - figure 2ECS Electronics SZ-019-DL Towbar Wiring Kits - figure 3 ECS Electronics SZ-019-DL Towbar Wiring Kits - figure 4 ECS Electronics SZ-019-DL Towbar Wiring Kits - figure 5 ECS Electronics SZ-019-DL Towbar Wiring Kits - figure 6 ECS Electronics SZ-019-DL Towbar Wiring Kits - figure 7 ECS Electronics SZ-019-DL Towbar Wiring Kits - figure 8 ECS Electronics SZ-019-DL Towbar Wiring Kits - figure 9 13-pole wiring-harness kit with C2-module.In this wiring-harness kit, the C2 module is used instead of a flasher relay with a C2 light failure sensor. A defective indicator of the car or/and caravan/trailer is stated by a quicker flashing of the other indicator lights (Following the European directive 76/756/EEC §4.5.8. and StVZO §54).This wiring kit recognizes when a trailer/caravan is connected with the connection Nr. 12 of the 13 pole socket. In the plug of the trailer/caravan, this connection has to be connected with the earth (connection Nr. 3).- In order to avoid an overload of the C2 module, a maximum of 21W in indicator lights can be connected on each side. The functioning of the C2-module can be tested by connecting the trailer/caravan (or a test-box with 21W lamps) and switching on the indicator lights with a removed indicator light. The other indicator lights will flash quicker. (ATTENTION: a test-box on which only LED’s are being used, can not be used in this case).ECS Electronics SZ-019-DL Towbar Wiring Kits - figure 10

Socket connection

DIN/ISO
11446
ECS Electronics SZ-019-DL Towbar Wiring Kits - symbol 1 ECS Electronics SZ-019-DL Towbar Wiring Kits - symbol 2 ECS Electronics SZ-019-DL Towbar Wiring Kits - symbol 3 ECS Electronics SZ-019-DL Towbar Wiring Kits - symbol 4 ECS Electronics SZ-019-DL Towbar Wiring Kits - symbol 5 ECS Electronics SZ-019-DL Towbar Wiring Kits - symbol 6 ECS Electronics SZ-019-DL Towbar Wiring Kits - symbol 5 ECS Electronics SZ-019-DL Towbar Wiring Kits - symbol 7 ECS Electronics SZ-019-DL Towbar Wiring Kits - symbol 8 ECS Electronics SZ-019-DL Towbar Wiring Kits - symbol 9 ECS Electronics SZ-019-DL Towbar Wiring Kits - symbol 10 ECS Electronics SZ-019-DL Towbar Wiring Kits - symbol 11 ECS Electronics SZ-019-DL Towbar Wiring Kits - symbol 12
1 / L 2 3/31 4/R 5/58-R 6/54 7/58-L 8 9 10 11 12 13
Pmax 21W 2x21W 21W 52W 3x21W 52W 2x21W 180W/15Amp. 180W/15Amp.
Yellow Blue White Green Brown Red (1,00m m²) Black Black/Red Brown/White Red(2,50 mm² ) White Red/Blue White

ECS Electronics logo

Documents / Resources

ECS Electronics SZ-019-DL Towbar Wiring Kits [pdf] Instruction Manual
SZ-019-DL, SZ-019-DL Towbar Wiring Kits, SZ-019-DL, Towbar Wiring Kits, Wiring Kits, Kits

References

Leave a comment

Your email address will not be published. Required fields are marked *